Hunza Wdl/hp User manual

Aug 2023 V2 Hunza-High-Power-Wall-Mount_Installation-Instructions-USA HUNZATM

PURE LED

IMPORTANT! TO MEET HUNZA’S BLACK LABEL WARRANTY,* PLEASE READ BEFORE INSTALLING THE FIXTURE.

PLEASE NOTE: THESE INSTRUCTIONS MUST NOT CONTRAVENE YOUR LOCAL ELECTRICAL AUTHORITY REGULATIONS,

WITH WHICH ALL INSTRUCTIONS HEREIN MUST COMPLY. PLEASE KEEP INSTRUCTIONS FOR FUTURE REFERENCE.

WARNING: DO NOT connect the secondary side (output) of a live driver to

the fixture, this will cause a spike in voltage that can damage the LED. When

connecting or disconnecting the fitting always insure the 120/240V power supply

is disconnected.

WARNING:When using a photocell and/or timer we recommend using devices

with relay outputs as opposed to electronic. The high frequency of electronic

devices can lead to failure of the LED driver.

WARNING: If the mounting surface is to be “acid washed” the fixtures must be

removed prior to the process to avoid damage to the fixture and its fittings.

WATERPROOFING FIXTURES: Ensure the fixture is fixed in place and ensure a

waterproof seal is made between the fixture and surface. Ensure that installation

on exteriors meets local authority regulations.

WATERPROOFING CONNECTIONS: Make sure to waterproof connections to the

luminaire, input cables and/or dimming cable. A non waterproof connection will

allow water to ingress into the power supply and/or fixture head which can lead

to failure.

*T&C’s apply. See website for details: hunzalighting.com/warranty

USA

WDL/HP PIL/HP WS/HP

Installation Guide

Step 1: Mount the Back Plate

• Apply sufficient silicone sealant to the groove on the back of the mounting plate, to seal against the wall.

• Fit cables through 25mm hole (If mounted on porous material e.g. mortar or if there is any possibility of water leaking down the cable track, the cable must be sealed

around the 25mm hole in the backplate to stop water building up in the Driver housing). Mount the back plate onto the wall. (See Fig. 1)

Step 2: Make Wire Connections

• Make a waterproof join between the cable tail and the output cable from the power supply. Make waterproof connections, please refer to wiring guide.

Step 3: Replace Fixture Onto Base

• Once connections have been made fix the luminaire onto the mounting plate (check that the backplate gasket is in place) and use screws provided to secure luminaire.

• Make sure to use the washers supplied are fitted under the mounting screws to stop water leaking into the luminaire. If there is any possibility of water leading down

the cable track, the cable entry point must be waterproof sealed. (See Fig. 2)

Step 4:Install Glare Guard/Snoot (Optional)

• Carefully remove lens ring making sure not to drop the glass lens and cause damage to it, keeping gasket in place.

• Hold the body of luminaire tightly and screw Glare Guard/Snoot ring onto luminaire.

• Still holding the body of the luminaire tightly rotate Glare Guard/Snoot to desired position.

High Power Wall Mount - Pillar Light, Wall Spot & Wall Down Light

INSTALLATION INSTRUCTIONS

Figure 1.

Figure 2.

PURE LED

Aug 2023 V2 Hunza-High-Power-Wall-Mount_Installation-Instructions-USA HUNZATM

2. All Hunza™ luminaires must be installed according to the installation

instructions supplied with the luminaires by a certificated electrician. The

installer is solely responsible for determining the correct wiring of series or

parallel luminaires.

3. All connections within the electrical system must be waterproof.

4. The environment in which the fixture is to be installed must be considered

carefully when selecting the finish. Solid Bronze, Copper or Stainless Steel

luminaires are recommended for high-risk environments such as near salt water

or salt laden air. Aluminium luminaires may not be covered by the full warranty

in these situations.

5. Bronze, Copper and Aluminium fixtures are not recommended for installation

in areas high in geothermal activity. Warranty is not offered for these materials in

geothermal areas.

6. For aluminium fixtures, warranty on the powder coat finish is excluded for

failure due to exposure to: chemical substances in the ground, fertilizers and

water containing corrosive agents.

7. Stainless Steel requires regular cleaning with fresh water when installed in

high salinity environments. (Refer to instructions supplied with luminaire). The

warranty does not cover tea staining or surface pitting caused by inadequate

maintenance procedures.

8. Hunza™ underwater fixtures are not covered by warranty in situations where

there are chemical imbalances in the water.

9. Warranty is excluded for corrosion due to electrolytic reactions caused by the

presence of electrical current in the ground or water.

10. Warranty excludes impact damage (except for glass lenses), incorrect

installation and incorrect re-assembly.

11. Fixtures must be kept properly maintained, including replacement of gaskets

and lenses when necessary and use of approved wattage lamps.

12. Fixtures must not be pressure washed (water blasted). Please refer to IP

ratings of each fixture.

13. Hunza™, at its discretion, may replace components to remedy the fault or

supply a replacement fixture.

14. Hunza™ warranty is limited to the repair or replacement of products ONLY.

Labour charges will not be accepted.

15. Warranty on transformers is limited to 5 years, and applies only when

transformers are installed in environments at less than 40 degrees Celsius

ambient temperature.

16. Hunza™ will not be liable for any labour charges for any repair or

replacement of defective drivers. Drivers have their own manufacturer warranty

and any faults will be at the responsibility of the manufacturer.

17. Hunza™ reserves the right to limit liability on non-standard (custom

designed) luminaires and/or delivery arrangements.

18. Damage caused by lightning strikes, high voltage spikes or incorrect polarity

connection is not covered by the Black Label warranty.

19. Polycarbonate and acrylic lenses are limited to a 5 year warranty.

20. N.B. Acrylic Quartz, Cloak, TIR or Bollard lenses must NOT be cleaned with

any petrochemical substance. This will void the warranty.

21. Warranty excludes halogen lamps and lamp holders, which are consumable

items.

22. Use of 3rd party colour correction gels and filters will void the warranty if

used with PureLED products.

HUNZA™ BLACK LABEL WARRANTY

When you purchase or specify a Hunza™ luminaire, you get the benefit of

the legendary Hunza™ reputation for high quality and long life. We back this

up with our Black Label extended warranty, offering up to 25 years on body

components and 5 years on the integral PURE LED™ system. When installed

and maintained properly, Hunza™ luminaires will last a lifetime so we keep

serviceability firmly in mind when designing the components and system

construction.

Hunza™ 25 Year Warranty All Hunza™ Cast Bronze luminaires have a 25

year replacement warranty against body corrosion, subject to the standard

conditions listed below.

Hunza™ 10 Year Warranty Hunza™ stainless steel* and copper luminaires have

a 10 year replacement warranty on body components, subject to the standard

conditions listed below (*excludes underwater fixtures ).

Hunza™ 5 Year Warranty All Hunza™ aluminium luminaires with a UV stable

powder-coat finish and underwater fixtures have a 5 year replacement warranty

on body components, subject to the standard conditions listed below.

Hunza™ Lifetime Warranty All glass lenses supplied with Hunza™ luminaires

have a lifetime warranty.

Hunza™ PURE LED™ System Integral PURE LED components have a 5 year

warranty and are subject to the standard conditions listed below.

Other Hunza™ Components 5 year warranty on other Hunza™ components,

Hunza™ accessories and are subject to the standard conditions listed below.

Third Party Components Coverage on plug-in (drop-in) LED lamps, power

supplies and other 3rd-party components are limited to the manufacturer’s

warranty.

STANDARD CONDITIONS:

1. Warranty is subject to proof of purchase being provided and begins at the

date of invoicing from the factory.

DO NOT USE BLEACH, concentrated cleaners, or solvents under any circumstances. DO NOT water blast/pressure blast

fixtures. DO NOT USE ABRASIVE COMPOUNDS.

POWDER-COATED ALUMINIUM: To keep your powdercoated aluminium fixtures in the best condition, please clean

by wiping gently with a damp, soft cloth or chamois and window cleaner. Do not use metal polishing compounds like

Brasso1, Autosol2 etc. To restore the lustre of the paint finish, use a silicon spray.

Powdercoated aluminium fixtures are not recommended for installation near the sea or close to salt water.

CAST BRONZE, COPPER AND BRASS will age naturally and will patina over time, it is not necessary to clean copper

frequently. When they do require cleaning, wipe them with a damp cloth. DO NOT use polishing compounds.

HUNZA PRODUCTIONS LTD

130 Felton Mathew Ave

Saint Johns, Auckland 1072

New Zealand

Ph: +64-9-528 9471

Fax: +64-9-528 9471

E: [email protected]

Hunza™ fixtures are available from specialist outdoor lighting distributors.

Specifications, Installation, IES, CAD & Guides are available online: www.hunzalighting.com

FOR 316 MARINE GRADE STAINLESS STEEL LUMINARIES: To maintain the finish of 316 stainless steel it is

recommended to wash the luminaire with fresh water from time to time to stop salt and corrosive elements building

up. For extra protection, we recommend applying a thin film of CLEAR SILICON GREASE (Moreys© Crystal Clear Food

Machinery MP2 Grease) to the exterior of fixture between maintenance.

ELECTRO POLISHES still require regular maintenance. Even an electro polished stainless steel fixture under an eave or

roof will suffer from the build up of salt deposits as it will not be washed away by rain.

MATERIAL MAINTENANCE

Made in New Zealand

by Hunza™ Productions LTD

PURE LED REPLACEMENT

CAUTION: Make sure that the power to the luminaire is switched off before attempting to change the lamp. Beware of hot luminaire and lamp. Make absolutely sure when changing lamps that the correct wattage

lamp is installed. Incorrect wattage lamps may cause HUNZA™ transformers to overload causing them to heat up and turn the luminaires off.

LED REPLACEMENT (PLEASE PAY CLOSE ATTENTION TO THE COMPONENT ORDER): Unscrew the lens ring from the front of the fixture. Carefully remove the lens, gasket and heat sink assembly, noting which

order they are installed. Unclip the “C” spring holder from the front of the heat sink and remove the plastic optic. Unscrew the two hex head screws holding the round LED board in place and remove the board.

Put the new LED board in place and reinsert the screws, using a small amount of white heat sink compound underneath the board. Replace the plastic optic and hold in place with the “C” clip. Insert the front

lens with the step facing outwards, put the gasket around the stop and hold in place while screwing the lens ring back in place, ensuring that the gasket is not bunched up.

USA

Wiring Guide

Make water proof connections using heavy walled adhesive lined heat shrink (refer to wiring guide below). Recommendations: Run all low voltage cables in flexible