Husky ERZ782478W4 User manual

Item Number: 458-424
Model Number: ERZ782478W4
4-LEVEL WELDED STEEL STORAGE RACK
77"W x 24"D x 78"H
Items you might find helpful
GUARANTEED FOREVER. If your Husky tool or storage
unit ever fails bring it back and we will replace it for free.
This full warranty gives you specific rights which vary from
state to state. If this product is defective contact the
manufacturer for repair or replacement parts.
Warranty
Contents
Description Quantity Part Number
A: frame 2 ERF7824BLK
B: beam 8 ERB72BLKN
C: tie channel 12 ER-V4-TB
D: wire deck 4 RWD2472SF
E: plastic push clip 16 BBC.118B
Components
General Instructions
Assembly of this unit is done by fitting the brackets of the
beams into the slots of the post frames.
A rubber mallet should be used on the ledge of the beams
to properly seat the beam brackets. If a hammer is used
care should be taken to protect the beam surface to avoid
damage by using a protective cloth or block of wood.
The stepped surface of the beam ledge is the top, and
should face upwards. This is the surface that the wire deck
will rest on.
A bracket should engage and fit firmly into the tapered slot
of the post frame. This engagement is a tight swaged fit
and will apply resistance as it fully engages. A visual
inspection should be made to show that the bracket is
properly engaged in the slot.
After assembly re-check each beam for proper
engagement.
Safety Instructions
This unit should be placed on a level surface. Failure to
do so can result in poor product performance or create a
possible safety hazard.
This unit should be securely anchored to a wall or floor
with suitable fasteners, which are not included.
Do not use this unit for anything other than the
manufacture’s intended purpose.
DO NOT STAND ON ANY PART
OF THE UNIT, OR USE IT AS A
LADDER.
Use care when working with
metal parts. Wear gloves for
protection.
Evenly distribute the weight on each level and always
keep the heavier loads on the bottom.
A: frame D: wire deck
B: beam
Rubber Mallet, Gloves
C: tie channel
E: plastic
push clip

Assembly Instructions
Wire Deck
Figure 3
• Attach the beams to the welded end frame
posts (see figure 1) starting at the bottom level
by using both end frames to establish the left
and the right sides of the units.
• After a beam has been placed in both end
frame post slots, tap the beam down at both
ends with a rubber mallet to help drive the
beam bracket tabs into the slots to secure the
beam. Continue assembling each level from
bottom to top level (front and back).
• If the beam bracket tabs become bent due to
mishandling, it may be necessary to adjust the
tabs back to their proper form.
• Place a plastic push clip into the hole of the
beam end bracket, then tap the plastic clip with
a mallet to drive it into the square hole of the
end frame post to secure the beam to the end
frame (see figure 1).
• The completed unit should have four (4) levels
evenly spaced for maximum stability.
• Although the beams are adjustable in height,
it’s recommended to evenly space them so that
the stability of the unit is not compromised.
• Install (3) tie channels in each level by inserting
the tab located on both ends of the tie channel
into the slot holes located along the inside
bottom edge of the beams (see figure 2).
• Insert wire deck on each level (figure 3).
• Assembly is now complete
• Husky Welded Storage Rack is engineered to offer maximum flexibility as well as ease and quickness of
assembly. The rack units can stand individually, or for greater stability, be joined together using the
common post.
• Individual beams can be adjusted without disturbing the beams in adjoining units.
• These instructions should be followed exactly. All parts supplied must be used as shown. Any alteration
or deviation from this instruction sheet can result in unit failure.
• After the unit is assembled, it must be placed on a level surface for safety, and optimal product
performance.
Figure 1
Beam Bracket Tabs
End Frame Post
End Frame
Post Slots
Plastic Push Clip
Beam
Figure 2
Inside Bottom
Edge of Beam
Tie
Channel
Tie Channel
Tab
Questions, problems, damage or missing part? Contact Husky’s partnered manufacturer for assistance:
Chat: www.edsal.com/chat or www.edsal.com/contact
Email: [e-mail]
Phone: [phone]
To obtain replacement parts please provide:
Model Number, Part Number & Description, Location Purchased, and Date Purchased
Edsal Manufacturing
Chicago, IL 60609
US Patents & Patents Pending
Assembled in USA
using global components
Rev: C081018_V4