Husqvarna Grass Catcher 2345 XLS Product manual

Blower Kit
48" Collection System
966004501
Operator and
Parts Manual

CONTENTS
CONGRATULATIONS on the purchase of a new
collection system. It has been designed, engineered
and manufactured to give you the best possible
dependability and performance.
Should you experience any problem you cannot
easily remedy, please contact your nearest
authorized service center/ department. They have
competent, well-trained technicians and the proper
tools for service and repairs.
Please read and retain this manual. The instructions
will enable you to assemble and maintain your
collection system properly. Always observe the
“SAFETY RULES”.
KNOW YOUR BLOWER SYSTEM
READ THIS OPERATION MANUAL AND SAFETY
RULES BEFORE ASSEMBLING OR OPERATING
YOUR BLOWER SYSTEM. Compare the
illustrations with the carton contents to familiarize
yourself with the parts before starting the assembly.
Study the operating instructions and safety
precautions thoroughly to insure proper functioning
of your Grass Catcher and to prevent injury to
yourself and others. Save this manual for future
reference.
The operation of any mower can
result in foreign objects thrown
into the eyes, which can result in
severe eye damage. ALWAYS wear
safety glasses or eye shields before
starting your mower and while
mowing. Standard safety glasses are
recommended or a wide vision safety
mask for over spectacles.
SAFETY RULES................................................. 4
GENERAL OPERATION ............................. 4
SLOPE OPERATION .................................. 4
CHILDREN.................................................. 5
SERVICE..................................................... 5
ASSEMBLY ........................................................ 8
TIPS FOR IMPROVED BAGGING............ 12
OPERATION..................................................... 13
GENERAL RECOMMENDATIONS ........... 13
STORAGE................................................. 13
REPAIR PARTS................................................ 14
WARNING!
Engine exhaust, some of its
constituents, and certain vehicle
components contain or emit
chemicals known to the State of
California to cause cancer and birth
defects or other reproductive harm.

4
SAFETY RULES
SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS
DANGER !
THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING
OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN
SERIOUS INJURY OR DEATH.
GENERAL OPERATION
• Read, understand and follow all instructions in the
manual and on the machine before starting.
• Onlyallowresponsibleadults,whoarefamiliar
with the instructions, to operate the machine.
• Cleartheareaofobjectssuchasrocks,stones,
toys,wireetc.,whichcouldbepickedupand
thrown by the blades.
• Besuretheareaisclearofallpeopleandpets
before mowing. Stop the machine if anyone enters
the area.
• Nevercarrypassengersorchildrenevenwith
blades off.
• Donotmowinreverseunlessabsolutely
necessary.Alwayslookdownandbehindbefore
andwhilebacking.
• Beawareofthemowerdischargedirectionanddo
not direct it towards anyone. Do not operate the
mower without either the entire grass catcher or
the guard in place.
• Slowdownbeforeturning.
• Neverleavethemachineunattendedwhenthe
engine is running. Always turn off the blades, set
theparkingbrake,stoptheengineandremove
thekeybeforeleavingthemachine.
• Turnoffbladeswhennotmowing.
• Stopenginebeforeremovinggrasscatcheror
unclogging chute.
• Mowonlyindaylightorgoodarticiallight.
• Donotoperatethemachinewhileunderthe
inuenceofalcoholordrugs.
• Watchoutfortrafcwhenoperatingnearor
crossing roadways.
• Useextracarewhenloadingandunloadingthe
machineontoatrailerortruck.
• Dataindicatesthatoperators,age60yearsand
above, are involved in a large percentage of riding
mower-related injuries. These operators should
evaluate their ability to operate the riding mower
safely enough to protect themselves and others
from serious injury.
• DO NOT operate mower with grass catcher,
unless the front weights are installed.
• Keep machine free of grass, leaves or other debris
buildup which can touch hot exhaust/engine parts
andburn.Donotallowthemowerdecktoplow
leaves or other debris which can cause buildup
to occur. Clean any oil or fuel spillage before
operating or storing the machine. Allow machine to
cool before storage.
SLOPE OPERATION
Slopes are a major factor related to loss-of-control
and tip-over accidents, which can result in severe
injury or death. All slopes require extra caution. If
youcannotbackuptheslopeorifyoufeeluneasy
on it, do not mow it.
DO
• Mowupanddownslopes(10°Max.),notacross.
• Removeobstaclessuchasrocks,treelimbs,etc.
• Watchforholes,ruts,orbumps.Uneventerrain
could overturn the machine. Tall grass can hide
obstacles.
• Use slow speed. Choose a low speed so that you
will not have to stop while on the slope.
• Useextracarewithgrasscatchersorother
attachments. These can change the stability of the
machine.
• Keepallmovementontheslopesslow and
gradual.Donotmakesuddenchangesinspeed
or direction.
• Avoidstartingorstoppingonaslope.Iftireslose
traction, disengage the blades and proceed slowly
straightdown the slope.

5
SAFETY RULES
SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS
DO NOT
• Donot turn on slopes unless necessary, and then,
turn slowly and gradually downhill, if possible.
• Donotmow near drop-off, ditches, or
embankments.Themowercouldsuddenlyturn
over if a wheel is over the edge of a cliff or ditch,
or if an edge caves in.
• Do notmow on wet grass. Reduced traction
could cause sliding.
• Do nottry to stabilize the machine by putting your
foot on the ground.
CHILDREN
Tragic accidents can occur if the operator is not
alert to the presence of children. Children are often
attracted to the machine and the mowing activity.
Never assume that children will remain where you
last saw them.
• NEVER allow children to operate the machine.
• Keepchildrenoutofthemowingareaandunder
the watchful care of another responsible adult.
• Bealertandturnoffthemachineifchildrenenter
the area.
• Beforeandwhenbacking,lookbehindanddown
for small children.
• Nevercarrychildren.Theymayfalloffandbe
seriously injured or interfere with safe machine
operation.
• Useextracarewhenapproachingblindcorners,
shrubs, trees, or other objects that may obscure
vision.
SERVICE
• Theoperationofanymowercanresultinforeign
objects thrown into the eyes, which can result
in severe eye damage. Always wear safety
glasses or eye shields while operating your
mower or performing any adjustments or repairs.
Werecommendawidevisionsafetymaskover
spectacles or standard safety glasses.
• Use extra care in handling gasoline and other
fuels.Theyareammableandvaporsare
explosive.
- Use only an approved container.
- Never remove gas cap or add fuel with the
engine running.
- Allow engine to cool before refueling.
 - Donotsmoke.
- Never refuel the machine indoors.
- Never store the machine or fuel container
insidewherethereisanopename,suchasa
water heater.
• Neverrunamachineinsideaclosedarea.
• Keepnutsandbolts,especiallybladeattachment
bolts,tightandkeepequipmentingoodcondition.
• Nevertamperwithsafetydevices.Checkthere
proper operation regularly.
CAUTION
In order to prevent accidental starting
when setting up, transporting,
adjusting or making repairs, always
disconnect spark plug wire and place
wire where it cannot contact spark
plug.

6
SAFETY RULES
SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS
• Keep machine free of grass, leaves, or other
debris buildup. Clean oil or fuel spillage. Allow
machine to cool before storing.
• Stopandinspecttheequipmentifyoustrikean
object. Repair, if necessary, before restarting.
• Nevermakeadjustmentsorrepairswiththe
engine running.
• Grasscatchercomponentsaresubjecttowear,
damage, and deterioration, which could expose
moving parts or allow objects to be thrown.
Frequentlycheckcomponentsandreplace
with manufacturer’s recommended parts, when
necessary.
• Mowerbladesaresharpandcancut.Wrapthe
blade(s)orweargloves,anduseextracaution
when servicing them.
• Checkbrakeoperationfrequently.Adjustand
service as shown in the Operator’s Manual.
WARNING!
DO NOT tow any trailers, etc. with
this mower. They may jackknife or
over turn causing damage to the
mower and possibly serious injury to
the operator.
WARNING!
Battery posts, terminals and related
accessories contain lead and lead
compounds, chemicals know to
the State of California to cause
cancer and birth defects or other
reproductive harm. Wash hands after
handling.

7
UNPACKING INSTRUCTIONS
• Removeallpartsandpackingmaterialsfrom
carton.
TOOLS REQUIRED
• 7/16"Wrenchorratchetandsocket
• ½"Wrenchorratchetandsocket
• 7/8"Socket
• Torque Wrench
• Phillips Head Screwdriver
• Hacksaw
• Pliers
NOTE: When right hand (R.H.) and left hand (L.H.) are mentioned in this manual, it means when
you are seated on the mower in the operator’s position.
Upper Chute
Bag Dump Indicator
Blower Housing
Middle Chute
CONTAINER CONTENTS
• BlowerAssembly • Drive Pulley
• BeltShield • Belt
• MountingBracket • Bag of Hardware
• Weight
Belt Cover
CAUTION
BEFORE ASSEMBLING GRASS CATCHER TO MOWER:
• Setparkingbrake.
• Placemotioncontrolleversin“NEUTRAL”position.
• Turnignitionkey“OFF”andremovekey.
• Makesurethebladesandallmovingpartshavecompletelystopped.
• Disconnectsparkplugandplacewirewhereitcannotcomeincontact
with plug.

8
1. Removethedischargechutefromthedeck.(Deck
congurationwillvarybysizeandmodel)
2. Lowerdecktothelowestcuttingposition.
3. Removetherighthand(dischargeside)beltcover
fromthedeck.
4. Relievethetensionfromthedeckbeltandremove
fromthecenterdeckpulley.
(SeeOperator’sManualifnecessary)
ASSEMBLY
1INSTALLING DRIVE PULLEY 2MOUNTING BLOWER ASSEMBLY
Outer Pulley Cover Pin
Hairpin Cotter
RearMountBracket
Contact Area
5. Removethenutsecuringtherighthanddeck
pulley to the spindle.
6. Installdrivepulleyincludedincollectionsystemkit
ontopofthecurrentdeckpulley.
7. Reinstall the nut on the spindle and torque to 55-
75 ft/lbs.
8. Reinstallthedeckbelt.
DeckHeight
Adjustment
Belt Cover
Discharge Chute
Drive Pulley
1. Position blower over the discharge tabs on the
deckandsetblowerontothedeck.
2. Besuretheblowerissittingushagainstthe
outsideofthedeck.
3. Installthefrontmountbrackettothedeckwiththe
pinandhairpincottersuppliedwiththekit.

9
ASSEMBLY
1. Makesurethetensionreleaseleverisforwardor
disengaged.
2. Placethebeltoverthepulleyonthedeck.Referto
illustration for proper routing.
3. Move the tension release arm to the rear and
engage in the latch.
3INSTALLING DRIVE BELT
RearOfDeck Idler Pulleys
Outer Pulley
Twist in Belt
Tension Release Arm
4INSTALLING BELT COVERS
1. Placethedeckbeltshieldonthedeckoverthe
drive pulley and secure with hardware removed
from steel belt shield.
2. Place retainer on the outer pulley cover.
3. Align the tab end of the belt cover into the slot on
thedeckbeltshieldandtheotherendovertheend
of the outer pulley cover.
4. Securewithknob.
Retainer
Knob
Outer Pulley Cover
DeckBeltShield
Belt Cover Tab
Middle Chute Latch
5TRIMMING MIDDLE CHUTE
1. Usingthehacksaw,trimalongthedashedline.
2. Locatethemiddlechute,atwasher,hoodlatch,
weldnut,lockwasherandmachinescrewfromkit.
3. Install in the appropriate hole at the upper end of
themiddlechute,accordingtodecksize.
Trim Line
Hood Latch
Weld Nut
Machine Screw
LockWasher
Latch Location
Flat Washer
6INSTALLING MIDDLE CHUTE
1. Place middle chute over the top end of the blower
assembly.
2. Latch middle chute to blower assembly.
Middle Chute
Blower Assembly

10
2. Install the bagger mount tube to the rear guard
with 5/16-18x3¼boltsandangenutsfromkit.
NOTE: Depending on model, rear guard hole may
need to be drilled out to 5/16"ifkithardwareistoo
large.
3. Installkitsupportstrapsontheoutsideofthe
mount tube as shown in the illustration. Using a
5/16-18 x 1¼ bolt, attach the front side of the strap
tothefendersupport.Donotaddangenutatthis
time. Place the reinforcement plate to the outside
of the fender support. Secure with additional 1¼
boltandfastenbothboltswithangenuts.Repeat
steps on opposite side.
NOTE:Thefrontsideofthekitsupportstraps
should be on the inside of the mower frame.
4. Tighten all hardware.
ASSEMBLY
1. To select the right support straps to use, measure
the mower frame just behind the casters, as
shown.
7INSTALLING BAGGER MOUNT
Reinforcement Plate
Mount Tube
Support Strap
For frames measuring 26" use support straps A,
for frames measuring 23" use support straps B.
A
B
Drill rear
guard hole to
5/16" if needed
Rear Guard

11
1. Position upper chute support against bagger inlet,
ushatouteredges.SeeIllustration.
2. Using support as a template, drill two 3/8holes into
bagger hood.
Upper Chute Support
Bagger Inlet
Nut
Bagger Hood
Flat Washers
Hex Bolt
Flex Trim
3. Secure upper chute support to hood with hex
bolts, washers and nyloc nuts.
ASSEMBLY
8INSTALLING CHUTE SUPPORT
3½ Bolt
WeightBracket
Weight Assembly
1. Boltcastweighttoweightbracketsusing3/8-16 x 3
bolts and four nuts.
2. Slidebothweightbracketsoverthefronttubeon
the frame. Be sure to position the weight assembly
in the center of the frame.
3. Secure with 3/8-16 x 3½ bolts and four nuts.
Front Tube
9INSTALLING WEIGHT KITS
3" Bolt
CAUTION
DO NOT operate mower with grass
catcher without front weights installed.
10MOUNTING COVER ASSEMBLY
NOTE: Assistance from another person may ease
mounting the cover assembly to mower.
1. Liftandrotatecovertoalignthecoverbrackets
with support assembly tubes.
2. Slide the cover down over the support tubes until
secure.

12
Remove plastic end caps from the center two bag1.
support arms. Fully insert spacer plugs into the
ends of the support tubes. It may be necessary
to tap the spacers into place with a hammer or
mallet.Replacetheplasticendcapbackoverthe
spacer. The additional extension will hold the hood
more securely when latched.
Remove center
end caps
Insert spacers
and replace caps
11INSTALLING SPACER PLUGS TIPS FOR IMPROVED BAGGING
Follow the mower operation instructions in you
mower operator’s manual.
When operating your grass catcher on a lawn where
grass and leaf bagging equipment has not been
used,youarepickingupthatchanddebristhathas
accumulated for long periods of time. The amount
collected and the total time of operation may be
greater than you will experience with regular use of
your grass catcher.
• Alwaysrunthrottleatfullspeedwhenbagging.
• Selectaspeedlowenoughtogivegoodmower
cutting performance, good quality cut and good
bagging performance.
NOTE:Itmaybenecessarytooverlapwidthof
cuttosuityourconditions.
• Ifgrassisextremelytall,itshouldbemowedtwice.
Thersttimerelativelyhigh,thesecondtimeto
desired height.
• Uselefthandsideofmowerfortrimming.
• Plastictrashbags(3.0mil,30gallon)canbe
inserted inside grass catcher containers for ease
of debris disposal. To remove the plastic trash
bags when full:
a. Disengage blades, shift into neutral, engage
theparkingbrakeandstoptheengine.
b. Unlatch and raise cover.
c. Remove one container at a time by grasping
container handles and pulling toward the rear,
off of the tube rails.
d. With the container resting on the ground, close
and secure the top of the plastic lawn bag.
 e. Tipthecontaineronitssideandslidethelled
bag from the container.
f. Install a new plastic lawn bag with the edges
of the bag draped over upper lip of the
Container(forreplacementbagsreferto
REPLACEMENTPARTS).
g. Repeat for other container.
 h. Reinstallcontainersmakingsureright
container overlaps left container at center
supports.
i. Close cover and secure latches over center
support tubes.
• Avoidcuttingwetgrassorinthemorningwhilethe
dew is still heavy. Grass clippings collected under
theseconditionstendtobestickyandadhereto
thewallsoftheowpathcausingclogging.
ASSEMBLY

13
• Ifthegrasscatcherfailstopickupcutgrass
or leaves, it is an indication that clogging has
occurred in the system or that the grass catcher
containers are full.
a. Disengage blades, place motion control levers
in neutral position.
- Unlatch and raise cover.
- Slide out containers and dispose of
clippings.
- Replace containers, close cover, and
latch.
 b. Unlatchchutesandcheckforclogging.
- Remove all debris in chute.
- Reassemble and latch chutes.
OPERATION
CAUTION
• DONOToperatemowerwith
grass catcher partially installed.
• Disengagebladesandstop
engine before leaving mower seat
to empty containers, unclogging
chutes, etc.
• Closecoverbeforestarting.
• Disengagemowerbladeswhen
crossing driveways or gravel
surfaces and other areas where
thrown objects could be a hazard.
• DONOTattempttovacuumcans
or other potentially hazardous
projectiles.
GENERAL RECOMMENDATIONS
Always observe safety rules when performing any
maintenance.
• Beforeeachusecheckforloosefasteners.
• Cleanunitthoroughlyaftereachuse.
BLADE CARE
Forbestresultsmowerbladesmustbekeptsharp.
Replace bent or damaged blades.
• SeeBLADECAREinstructionsinyourmower
operator’s manual.
STORAGE
When grass catcher is to be stored for a period
of time, clean it thoroughly, remove all dirt, grass,
leaves, etc. Store in a clean, dry place.
CAUTION
Do not leave grass in bagger
containers. Empty containers after
each use and before storing. Failure
to do so may result in spontaneous
combustion which could develop into
are.
CAUTION
Grass catcher components are
subject to wear, damage and
deterioration, which could expose
moving parts or allow objects
to be thrown. Frequently check
components and replace with
manufacturer’s recommended parts,
when necessary.
CAUTION
BEFORE PERFORMING
MAINTENANCE, SERVICE OR
ADJUSTMENTS:
• Setparkingbrake.
• Placemotioncontrolleversin
“NEUTRAL”position.
• Placeclutchcontrolin
“DISENGAGED”position.
• Turnignitionkeyto“OFF”
position.
• Makesurebladesandallmoving
parts have completely stopped.
• Disconnectsparkplugwire(s)
from spark plug(s) and place wire
where it cannot come in contact
with plug.

14
4
5
7
8
9
10
11
13
14
Torque to
30 ft/lbs
15
16
17
18
19
20
21
22
23
39
26
25
29
30
38
28
24
1
2
3
6
10
12
14
15
23
33
34
35
36
31
44
32
37
44
43
11
40
47
48
50
51
52
53
51
42
45
46
27
49
48
41
45
40
47
44
55
11
59
56
11
40
56
11
60
12
REPAIR PARTS
57
54

15
539 1019771.. .... 1.... TRACTION SPRING
539 9769522.. .... 1.... SCREW 10-24 x .625 RD
539 1044113.. .... 1.... KNOB W/STUD
539 1047634.. .... 1.... RETAINER U TYPE
539 1057855.. .... 1.... DECAL, WARNING
539 1067416.. .... 1.... DECAL, SEVERING
539 1080847.. .... 1.... WASHER, 3/16 x ¾ x 16 GA
539 1080888.. .... 1.... LATCH, HOOD
539 1080899.. .... 1.... WELD NUT, PLATED
539 10812010.. .... 2.... NUT ¼-20 HEX NYLOC
539 99071711.. .... 5.... NUT 5/16-18 HEX NYLOC
539 10873512.. .... 2.... NUT ¼-20 HEX FLANGE
539 10955213.. .... 2.... WASHER 3/16 LOCK
539 11032114.. .... 2.... BOLT, HEX 3/8-24 x 1¼ GR 8
539 11032315.. .... 2.... WASHER, HARDENED
539 11368316.. .... 1.... V-IDLER
539 11566717.. .... 1.... KEY 3/16 x ½
539 12522918.. .... 1.... KEY 3/16 x 1½
539 13029219.. .... 1.... IMPELLER
539 13029320.. .... 1.... COVER, BELT
539 13029521.. .... 1.... HUB, BEARING
539 13029622.. .... 2.... BEARING
539 13030123.. .... 2.... BUSHING
539 13030924.. .... 1.... COVER, OUTER PULLEY
539 13031325.. .... 6.... NUT 5/16-18 TEE
539 13031426.. ...11 .... NUT ¼-20 TEE
539 13031527.. .... 6.... HCS 5/16-18 x ½
539 13031628.. .... 1.... SHAFT, IMPELLER
539 13031729.. .... 1.... PIN
539 13032330.. .... 1.... SPACER
539 13032431.. .... 1.... PULLEY
ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. DESCRIPTION
539 13033532.. .... 1.... MOUNT, IDLER, UPPER
539 13033633.. .... 1.... MOUNT, IDLER, LOWER
539 13033734.. .... 1.... ARM, IDLER
539 13033835.. .... 1.... ARM, TENSION
539 13033936.. .... 1.... BRACKET, MOUNT, FRONT
539 13034037.. .... 1.... BRACKET, MOUNT, REAR
539 13034138.. .... 1.... PLATE, OUTER
539 13034639.. .... 1.... KEEPER
539 20028240.. .... 3.... NUT 3/8-16 HEX JAM NYLOC
539 91907841.. .... 1.... PULLEY, IDLER
539 97694942.. .... 1.... HCS 3/8-16 x 1¾
539 97698843.. .... 1.... HAIRPIN COTTER
539 99005544.. .. 13.... WASHER ¼ FLAT SAE
539 99030245.. .... 8.... SCREW ¼ x 3/8THRD FRM
539 10846146.. .... 3.... HCS ¼-20 x ½
539 99011847.. .... 2.... WASHER 3/8SPLT LOCK
539 99012248.. .... 2.... WASHER 3/8SAE FLT
539 99020949.. .... 1.... HCS 5/16-18 x 1
539 99031650.. .... 4.... RHSNB 5/16-18 x ¾
539 99064351.. .... 2.... HCS ¼-20 x 7/8
539 99065552.. .... 1.... HCS 3/8-16 x 1½
539 99069253.. .... 1.... WASHER 5/16 STD FLT
53954.. 130349.... 1.... DECAL, BELT ROUTING
53955.. 131085.... 1.... KEEPER, BELT, OUTER
53956.. 131087.... 2.... KEEPER, BELT, REAR
53957.. 132122.... 1.... PLATE, BACKING
53958.. 132124.... 1.... PLATE, BACKING
539 99020859.. .... 4.... RHSNB 5/16-18 x 1
539 99064560.. .... 1.... RHSNB 3/8-16 x 1
539 13034461.. .... 1.... HOUSING w/DECALS
REPAIR PARTS
NOTE: ALL FASTENERS ARE GRADE 5 UNLESS OTHERWISE SPECIFIED.

16
6
5
4
4
3
3
1
9
2
12
107
8
11
REPAIR PARTS

17
539 1080811.. .... 1.... SCREW, SPEC 10-14 x ½
539 1080822.. .... 1.... INDICATOR, BAG DUMP
539 1080833.. .... 2.... SCREW 10-24 x 11/8
539 1080844.. .... 3.... WASHER 3/16 x ¾
539 1080855.. .... 2.... SPACER, SPLIT
539 1080866.. .... 2.... NUT, ACORN 10-24
ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. DESCRIPTION
REPAIR PARTS
539 1080887.. .... 1.... LATCH, HOOD
539 1080898.. .... 1.... WELD NUT, PLATED
522 7392019.. .... 1.... CHUTE, UPPER
539 10955210.. .... 2.... WASHER 3/16 LOCK
539 13029411.. .... 1.... CHUTE, MIDDLE
539 97695212.. .... 1.... SCREW 10-24 x .625 MACH
NOTE: ALL FASTENERS ARE GRADE 5 UNLESS OTHERWISE SPECIFIED.

18
1
2
4
6
7
8
9
10
11
7
5
12
12
3
3
REPAIR PARTS

19
532 1927091.. .... 1.... SCREEN, COVER
532 1953732.. .... 1.... COVER
539 9769523.. .... 6.... SCREW #10-24 x 5/8
539 1080964.. .... 2.... HAIR PIN
539 1080975.. .... 4.... PLUG, TUBING END
532 1769906.. .... 1.... BAGGER, FRAME
532 1927867.. .... 2.... PIN, HINGE
532 1925508.. .... 1.... SEAL, COVER
532 4002269.. .... 3.... CONTAINER, SOFT BAG
532 19260310.. .... 1.... GASKET, COVER
532 13089511.. .... 2.... HANDLE, BAGGER COVER
539 97697712.. .. 14.... NUT #10-24 CROWNLOCK
NOTE: ALL FASTENERS ARE GRADE 5 UNLESS OTHERWISE SPECIFIED.
ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. DESCRIPTION
REPAIR PARTS

20
REPAIR PARTS
26
25
19
18
14
21
27
7
610
13
12
16
17
22
4
2
3
1
5
11
24
15
24
20
23 8
24 28
17
24

21
ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. DESCRIPTION
REPAIR PARTS
539 1115871.. .... 1.... WEIGHT PLATE
522 9232022.. .... 2.... WEIGHT BRACKET
521 9965013.. .... 8.... NUT 3/8-16 HEX FLANGE
539 1082714.. .... 4.... HCS 3/8-16 x 3½
539 1013415.. .... 4.... HCS 3/8-16 x 3
539 1303066.. .... 1.... SHIELD, BELT
539 1303197.. .... 1.... PULLEY
539 1057438.. .... 1.... DECAL, NO STEP
539 1303429.. .... 1.... PLATE, MOUNT
539 13034710.. .... 1.... BELT
539 10047211.. .... 2.... RHSNB 5/16-18 x 1¼
539 99071712.. .... 2.... NUT 5/16-18 HEX NYLOC
539 13109113.. .... 1.... TUBE, MOUNT
539 97693714.. .... 2.... HCS 5/16-18 x 2
539 99069215.. .... 4.... WASHER 5/16 STD FLT
539 99062716.. .... 2.... HCS 5/16-18 x 1¼
539 99018817.. .... 6.... WASHER 5/16 SAE FLAT
539 11023418.. .... 1.... SUPPORT, HOSE
539 11229419.. .... 1.... FLEX TRIM, BLACK
523 08490220.. .... 1.... STRAP, SUPPORT, RT
For 28" Frame
523 08470221.. .... 1.... STRAP, SUPPORT, LT
For 28" Frame
522 80130122.. .... 2.... SPACER PLUG
539 10152023.. .... 2.... HCS 5/16-18 x 3¼
539 11289924.. .... 8.... NUT 5/16-18 HEX FLG NYLOC
522 85440225.. .... 1.... STRAP, SUPPORT, RT
For 26" Frame
522 85450226.. .... 1.... STRAP, SUPPORT, LT
For 26" Frame
523 11280227.. ... 2.... PLATE, REINFORCEMENT
539 99020928.. .... 2.... HCS 5/16-18 x 1
NOTE: ALL FASTENERS ARE GRADE 5 UNLESS OTHERWISE SPECIFIED.