Husqvarna CG 200 User manual

English (2-15)
Français (16-29)
Deutsch (30-43)
Nederlands (44-57)
Operator's manual
Manuel d'utilisation
Bedienungsanweisung
Gebruiksaanwijzing
CG 200
Read the operator's manual carefully and make sure that you understand the instructions before
you use the product.
Lisez attentivement le manuel d'utilisation et assurez-vous que vous en comprenez le contenu
avant d’utiliser la machine.
Lesen Sie die Bedienungsanweisung sorgfältig durch und machen Sie sich mit dem Inhalt vertraut,
bevor Sie das Gerät benutzen
Lees de gebruiksaanwijzing zorgvuldig door en gebruik de machine niet voordat u de instructies
goed hebt begrepen.

Contents
Introduction..................................................................... 2
Safety..............................................................................5
Assembly........................................................................ 7
Operation........................................................................ 8
Maintenance................................................................. 10
Troubleshooting............................................................ 11
Transportation, storage and disposal........................... 12
Technical data.............................................................. 13
Service..........................................................................14
EC Declaration of Conformity....................................... 14
Introduction
Product description
To be used on concrete, asphalt, paint and other
coatings, glue and steel, and should not be used for any
other purpose than described in this manual.
Intended use
For scarifying, milling grooving, texturing, and cleaning.
2130 - 003 - 18.08.2017

Product overview
130 - 003 - 18.08.2017 3

1. Safety lever (operator presence control)
2. Steering shaft
3. Shaft adjustment knob
4. Depth adjustment knob (mm)
5. Quick raise/lower lever
6. Lifting eye
7. Engine / Motor
8. Belt tensioner
9. Chassis
10. Transmission
11. Belt guard
12. On / off switch
13. Drum guard plate
14. Drum guard fasteners
15. 200 mm wide drum
16. Drain extension
17. Dust extractor hose
18. Type plate
Symbols on the product
WARNING! The product can be a
dangerous tool if used incorrectly or
carelessly, which can cause serious or fatal
injury to the operator or others.
Please read the instructions for use prior to
operating the product for the first time.
This symbol indicates that the product is in
conformance with the applicable European
directive.
Wear personal protective equipment. See
Personal protective equipment on page 7
for instructions.
Noise emission to the environment
according to the European Community’s
Directive. The product’s emission is
specified in the Technical data chapter and
on the label.
Hot surface.
WARNING! Dust forms when cutting, this
can cause injuries if inhaled. Use an
approved breathing mask. Avoid inhaling
exhaust fumes. Always provide for good
ventilation.
Caution, risk of cutting.
Low speed.
High speed.
Choke control.
Environmental marking. Symbols on the
product or its packaging indicate that this
product cannot be handled as domestic
waste. It must instead be submitted to an
appropriate recycling station for the recovery
of electrical and electronic equipment. By
ensuring that this product is taken care of
correctly, you can help to counteract the
potential negative impact on the
environment and people that can otherwise
result through the incorrect waste
management of this product. For more
detailed information about recycling this
product, contact your municipality, your
domestic waste service or the shop from
where you purchased the product.
Other symbols/decals on the product refer to special
certification requirements for certain markets.
4130 - 003 - 18.08.2017

Type plate
CG200
HUSQVARNA AB, SE-561 82 HUSKVARNA, SWEDEN
MADE IN CHINA
S/N: YYY WWWXXXXX P/N: XXX XXX XXX
XXXkg
XXXHzXXXkWIPX3220-240V~
XXX XXX XXXrpm
1. Voltage power supply
2. Water proof
3. Nominal engine output
4. Frequency
5. Rotations per minute
6. Gross vehicle weight
7. Manufacturing date, year, week, serial number
8. Product number
Product liability
Before leaving our factory every product passes an
exacting inspection programme in which everything is
checked minutely. Following the instructions will ensure
that your product gives long service, in normal operating
conditions.
The manufacturer declines all responsibility for loss or
damage resulting from misuse or any modification,
alteration or powering that does not conform to the
manufacturer's original specifications.
The user advice and spare parts mentioned in this
document are given as an indication, and do not
constitute an undertaking. No warrantee will be granted
in the event of errors or omissions, or for damage
occurring during delivery, or caused by the design or
use of the product. We are very concerned about the
quality of our products and we reserve the right to make
any technical modifications to improve them, without
warning.
Safety
Safety definitions
Warnings, cautions and notes are used to point out
specially important parts of the operator's manual.
WARNING: Used if there is a risk of injury or
death for the operator or bystanders if the
instructions in the manual are not obeyed.
CAUTION: Used if there is a risk of damage
to the product, other materials or the
adjacent area if the instructions in the
manual are not obeyed.
Note: Used to give more information that is necessary in
a given situation.
General safety instructions
WARNING: Please read the operator’s
manual carefully and make sure you
understand the instructions before using the
product.
WARNING: Please read the engine
operation manual that is supplied with the
engine and make sure you understand the
instructions before using the product.
The product is designed to provide safe and reliable
service in operating conditions corresponding with the
instructions, but it can present dangers for the user and
risks of damage, consequently regular on site inspection
is necessary to ensure:
130 - 003 - 18.08.2017 5