Husqvarna 5521P User manual

English/French
532 44 65-63 Rev. 2
Operator’s Manual
Manuel de L’Opérateur
5521P / 961330016
Gasoline containing up to 10% ethanol (E10) is accept-
able for use in this machine. The use of any gasoline ex-
ceeding10%ethanol(E10)willvoidtheproductwarranty.
Vous pouvez utiliser de l’essence contenant jusqu’à
10 % d’éthanol (E10) avec cet appareil. L’utilisation
d’essence contenant plus de 10 % d’éthanol annulera
la garantie du produit. Please read the operator's manual carefully and make sure
you understand the instructions before using the machine.
Lisez très attentivement et soyez certain de comprende
ces instructions avant d’utiliser cette machine.

2
WARNING: Battery posts, terminals and
related accessories contain lead and lead
compounds, chemicals known to the State
of California to cause cancer and birth
defects or other reproductive harm. Wash
hands after handling.
WARNING: Engine exhaust, some of its
constituents, and certain vehicle compo-
nents contain or emit chemicals known to
the State of California to cause cancer and
birth defects or other reproductive harm.
CAUTION: Always disconnect spark plug
wire and place wire where it cannot contact
spark plug in order to prevent accidental
starting when setting up, transporting,
adjusting or making repairs.
Look for this symbol to point out im-
portant safety precautions. It means
CAUTION!!! BECOME ALERT!!! YOUR
SAFETY IS INVOLVED.
CAUTION: Muffler and other engine parts
become extremely hot during operation
and remain hot after engine has stopped.
Toavoidsevereburnsoncontact,stayaway
from these areas.
Safe Operation Practices for Walk-Behind Mowers
IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEETAND THROWING OBJECTS. FAILURE
TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
SAFETY RULES
I. GENERAL OPERATION
• Read, understand, and follow all instructions on the
machine and in the manual(s) before starting. Be thor-
oughly familiar with the controls and the proper use of
the machine before starting.
• Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
• Only allow responsible individuals, who are familiar
with the instructions, to operate the machine.
• Clear the area of objects such as rocks, toys, wire,
bones,sticks,etc., which couldbepicked upandthrown
by the blade.
• Be sure the area is clear of other people before mow-
ing. Stop machine if anyone enters the area.
• Do not operate the mower when barefoot or wearing
open sandals. Always wear substantial foot wear.
• Do not pull mower backwards unless absolutely nec-
essary. Always look down and behind before and while
moving backwards.
• Never direct discharged material toward anyone.
Avoid discharging material against a wall or obstruc-
tion. Material may richochet back toward the operator.
Stop the blade when crossing gravel surfaces.
• Do not operate the mower without proper guards,
plates, grass catcher or other safety protective devices
in place.
• See manufacturer’s instructions for proper operation
and installation of accessories. Only use accessories
approved by the manufacturer.
• Stop the blade(s) when crossing gravel drives, walks,
or roads.
• Stop the engine (motor) whenever you leave the equip-
ment, before cleaning the mower or unclogging the
chute.
• Shuttheengine(motor)offandwaituntilthebladecomes
to complete stop before removing grass catcher.
• Mow only in daylight or good artificial light.
• Do not operate the machine while under the influence
of alcohol or drugs.
• Never operate machine in wet grass. Always be sure of
your footing: keep a firm hold on the handle and walk;
never run.
• Disengagetheself-propelled mechanismordrive clutch
onmowerssoequippedbeforestartingtheengine(motor).
• If the equipment should start to vibrate abnormally,
stop the engine (motor) and check immediately for the
cause. Vibration is generally a warning of trouble.
• Always wear safety goggles or safety glasses with side
shields when operating mower.
II. SLOPE OPERATION
Slopes are a major factor related to slip and fall accidents
which can result in severe injury. All slopes require extra
caution. If you feel uneasy on a slope, do not mow it.
DO:
• Mowacrossthefaceofslopes:neverupanddown. Exer-
ciseextremecautionwhenchangingdirection onslopes.
• Remove obstacles such as rocks, tree limbs, etc.
• Watch for holes, ruts, or bumps. Tall grass can hide
obstacles.
DO NOT:
• Do not trim near drop-offs, ditches or embankments.
The operator could lose footing or balance.
• Do not trim excessively steep slopes.
• Donot mowon wetgrass. Reducedfooting couldcause
slipping.
III. CHILDREN
Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted to
the machine and the mowing activity. Never assume that
children will remain where you last saw them.
• Keep children out of the trimming area and under the
watchful care of another responsible adult.
• Be alert and turn machine off if children enter the
area.
• Before and while walking backwards, look behind and
down for small children.
• Never allow children to operate the machine.
• Useextracare whenapproachingblind corners,shrubs,
trees, or other objects that may obscure vision.
IV. SAFE HANDLING OF GASOLINE
Use extreme care in handling gasoline. Gasoline is ex-
tremely flammable and the vapors are explosive.
• Extinguishallcigarettes,cigars, pipesandothersources
of ignition.
• Use only an approved container.
• Never remove gas cap or add fuel with the engine run-
ning. Allow engine to cool before refueling.

3
CONGRATULATIONS on your purchase of a new lawn
mower. Ithasbeen designed,engineeredandmanufactured
togiveyouthe bestpossibledependabilityand performance.
Should you experience any problem you cannot easily
remedy, please contact your nearest authorized service
center. We have competent, well-trained technicians and
the proper tools to service or repair this lawn mower.
Please read and retain this manual. The instructions will
enable you to assemble and maintain your lawn mower
properly. Always observe the “SAFETY RULES”.
SERIAL
NUMBER: _________________________________
DATE OF PURCHASE: _______________________
THEMODELANDSERIALNUMBERSWILLBEFOUND
ON ADECALATTACHEDTOTHEREAROFTHE LAWN
MOWER HOUSING.
YOUSHOULD RECORDBOTH SERIALNUMBERAND
DATE OF PURCHASE AND KEEP IN A SAFE PLACE
FOR FUTURE REFERENCE.
CUSTOMER RESPONSIBILITIES
• Read and observe the safety rules.
• Follow a regular schedule in maintaining, caring for
and using your lawn mower.
• Follow the instructions under “Maintenance” and “Stor-
age” sections of this owner’s manual.
TABLE OF CONTENTS
SAFETY RULES ......................................................... 2-3
PRODUCT SPECIFICATIONS....................................... 3
CUSTOMER RESPONSIBILITIES................................. 3
ASSEMBLY.................................................................... 4
OPERATION ............................................................... 5-8
MAINTENANCE SCHEDULE ........................................ 9
MAINTENANCE........................................................ 9-11
SERVICE AND ADJUSTMENTS ................................. 12
STORAGE.................................................................... 13
TROUBLESHOOTING................................................. 14
WARRANTY............................................................15-18
• Never refuel the machine indoors.
• Never store the machine or fuel container where there
is an open flame, spark or pilot light such as a water
heater or on other appliances.
• Neverfill containersinside a vehicle,on atruck ortrailer
bed with a plastic liner. Always place containers on
the ground away from your vehicle before filling.
• Removegas-poweredequipmentfromthetruck ortrailer
and refuel it on the ground. If this is not possible, then
refuel such equipment with a portable container, rather
than from a gasoline dispenser nozzle.
• Keep the nozzle in contact with the rim of the fuel tank
orcontaineropening atalltimes until fuelingiscomplete.
Do not use a nozzle lock-open device.
• If fuel is spilled on clothing, change clothing immedi-
ately.
• Never overfill fuel tank. Replace gas cap and tighten
securely.
V. GENERAL SERVICE
• Never run a machine inside a closed area.
• Never make adjustments or repairs with the engine
(motor) running. Disconnect spark plug wire, and keep
wire away from plug to prevent accidental starting.
• Keep nuts and bolts, especially blade attachement
bolts, tight and keep equipment in good condition.
• Never tamper with safety devices. Check their proper
operation regularly.
• Keep machine free of grass, leaves, or other debris
build-up. Clean oil or fuel spillage. Allow machine to
cool before storing.
• Stop and inspect the equipment if you strike an object.
Repair, if necessary, before restarting.
• Never attempt to make wheel height adjustments while
the engine (motor) is running.
• Grass catcher components are subject to wear, dam-
age, and deterioration, which could expose moving
parts or allow objects to be thrown. Frequently check
components and replace with manufacturer’s recom-
mended parts, when necessary.
• Mower blade is sharp and can cut. Wrap the blade or
wear gloves, and use extra caution when servicing it.
• Donotchange the enginegovernorsettingor overspeed
the engine.
• Maintain or replace safety and instruction labels, as
necessary.
WARNING: This lawn mower is equipped with an internal combustion engine and should not be used on or
near any unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is
equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be
maintained in effective working order by the operator.
In the state of California the above is required by law (Section 4442 of the California Public Resources Code). Other
states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available
through your nearest authorized service center.
PRODUCT SPECIFICATIONS
Gasoline Capacity 1.6 Quarts
and Type: (Unleaded Regular Only)
Oil Type (API SG–SL): SAE 30 (above 32°F);
SAE 5W-30 (below 32°F)
Oil Capacity: 16 Ounces
Spark Plug (Gap: .030"): Champion RC12YC
Blade Bolt Torque: 35-40 ft. lbs.

4
ASSEMBLY
Read these instructions and this manual in its entirety before you attempt to assemble or operate your new lawn mower.
IMPORTANT: THIS LAWN MOWER IS SHIPPED WITHOUT OIL OR GASOLINE IN THE ENGINE.
Your new lawn mower has been assembled at the factory with the exception of those parts left unassembled for shipping
purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts
bag. To ensure safe and proper operation of your lawn mower, all parts and hardware you assemble must be tightened
securely. Use the correct tools as necessary to ensure proper tightness.
TO ASSEMBLE GRASS CATCHER
(See Fig. 2)
1. Put grass catcher frame into grass bag with rigid part
of bag on the bottom. Make sure the frame handle is
outside of the bag top.
2. Slip vinyl bindings over frame.
NOTE: Ifvinyl bindingsaretoo stiff,holdthem inwarm water
for a few minutes. If bag gets wet, let it dry before using.
TO INSTALL ATTACHMENTS
Your lawn mower was shipped ready to be used as a
mulcher. To convert mower to bagging or discharging,
see “TO CONVERT MOWER” in the Operation section of
this manual.
FIG. 1
OPERATOR
PRESENCE
CONTROL
BAR
HANDLE
KNOB
LIFT
UP
LIFT
UP
LOWER
HANDLE
MOWING
POSITION
UPPER
HANDLE
FIG. 2
FRAME
HANDLE
VINYL
BINDINGS FRAME
OPENING
TO REMOVE LAWN MOWER FROM CARTON
1. Remove loose parts included with mower.
2. Cut down two end corners of carton and lay end panel
down flat.
3. Remove all packing materials except padding between
upper and lower handle and padding holding operator
presence control bar to upper handle.
4. Roll lawn mower out of carton and check carton thor-
ougly for additional loose parts.
HOW TO SET UPYOUR LAWN MOWER
TO UNFOLD HANDLE (See Fig. 1)
IMPORTANT: UNFOLD HANDLE CAREFULLY SO AS
NOT TO PINCH OR DAMAGE CONTROL CABLES.
1. Raise handles until lower handle section locks into
place in mowing position.
2. Remove protective padding, raise upper handle sec-
tion into place on lower handle and tighten both handle
knobs.
3. Remove handle padding holding operator presence
control bar to upper handle.
Your handles may be adjusted for your mowing comfort.
Referto“ADJUSTHANDLE” in theServiceandAdjustments
section of this manual.

5
KNOW YOUR LAWN MOWER
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR LAWN MOWER.
Compare the illustrations with your lawn mower to familiarize yourself with the location of various controls and adjustments.
Save this manual for future reference.
OPERATOR PRESENCE CONTROL BAR – must be
held down to the handle to start the engine. Release to
stop the engine.
HOUSING
GRASS
CATCHER
STARTER HANDLE – used for starting the engine.
MULCHER DOOR – allows conversion to discharge or
bagging operation.
OPERATOR PRESENCE CONTROL BAR
WHEEL ADJUSTER
(ON EACH WHEEL)
STARTER
HANDLE
ENGINE OIL CAP
WITH DIPSTICK
HANDLE KNOB
GASOLINE
FILLER CAP
These symbols may appear on your lawn mower or in literature supplied with the product. Learn and understand
their meaning.
OPERATION
MUFFLER
AIR FILTER
MULCHER DOOR
SPARK
PLUG
MEETS CPSC SAFETY REQUIREMENTS
Our rotary walk-behind power lawn mowers conform to the safety standards of the American National Standards Institute
and the U.S. Consumer Product Safety Commission. WARNING: The blade turns when the engine is running.
NOTE: Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine.
The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty.
IMPORTANT: This lawn mower is shipped
WITHOUT OIL OR GASOLINE in the engine.

6
TO CONVERT MOWER
Your lawn mower was shipped ready to be used as a
mulcher. To convert to bagging or discharging:
REAR BAGGING (See Fig. 4)
• Lift rear door of the lawn mower and place the grass
catcher frame hooks onto the door pivot pins.
• To converttomulchingor dischargingoperation,remove
grass catcher and close rear door.
FIG. 4
PIVOT PINS REAR
DOOR
GRASS
CATCHER
HANDLE
CATCHER FRAME HOOK
HOW TO USE YOUR LAWN MOWER
ENGINE SPEED
The engine speed was set at the factory for optimum per-
formance. Speed is not adjustable.
ENGINE ZONE CONTROL
CAUTION: Federal regulations require
an engine control to be installed on this
lawnmowerin order tominimizethe risk
of blade contact injury. Do not under
any circumstances attempt to defeat
the function of the operator control.
The blade turns when the engine is
running.
• Yourlawn mowerisequipped withanoperator presence
control bar which requires the operator to be positioned
behind the lawn mower handle to start and operate the
lawn mower.
TO ADJUST CUTTING HEIGHT (See Fig. 3)
Raise wheels for low cut and lower wheels for high cut,
adjust cutting height to suit your requirements. Medium
position is best for most lawns.
• To changecutting height, squeezeadjusterlever toward
wheel.Movewheelupor downtosuityourrequirements.
Be sure all wheels are in the same setting.
NOTE:Adjusteris properlypositionedwhen plate tabinserts
into hole in lever.Also, 9-position adjusters (if so equipped)
allow lever to be positioned between the plate tabs.
The operation of any lawn mower can result in foreign objects thrown into the eyes, which can result in
severe eye damage. Always wear safety glasses or eye shields while operating your lawn mower or per-
forming any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask
over spectacles.
OPERATION
SIDE DISCHARGING (See Fig. 5)
• Rear door must be closed.
• Open mulcher door and install discharge deflector
under door as shown.
• Mower is now ready for discharging operation.
• To convert tomulching or bagging operation, discharge
deflector must be removed and mulcher door must be
closed.
FIG. 3
LEVER BACKWARD TO LOWER MOWER
LEVER FORWARD TO RAISE MOWER
PLATE
TAB
LEVER
FIG. 5
OPEN
MULCHER DOOR
INSTALL
DISCHARGE
DEFLECTOR

7
SIMPLE STEPS TO REMEMBER
WHEN CONVERTING YOUR LAWN MOWER:
FOR MULCHING -
1. Rear door closed.
2. Mulcher door closed.
FOR REAR BAGGING -
1. Grass catcher installed.
2. Mulcher door closed.
FOR SIDE DISCHARGING -
1. Rear door closed.
2. Discharge deflector installed.
CAUTION: Donot run yourlawn mower
without rear door closed or approved
grass catcher in place. Never attempt
to operate the lawn mower with the rear
door removed or propped open.
OPERATION
TO EMPTY GRASS CATCHER (See Fig. 6)
1. Lift up on grass catcher using the frame handle.
2. Remove grass catcher with clippings from under lawn
mower handle.
3. Empty clippings from bag.
NOTE: Do not drag the bag when emptying; it will cause
unnecessary wear.
FIG. 6
FRAME
HANDLE
MOWER IS NOW READY FOR
DISCHARGING OPERATION
FIG. 5
BEFORE STARTING ENGINE
ADD OIL (See Fig. 7)
Your lawnmower is shipped without oil in the engine. For
type and grade of oil to use, see “ENGINE” in the Mainte-
nance section of this manual.
CAUTION: DO NOT overfill engine with
oil, or it will smoke heavily from the
muffler on startup.
1. Be sure lawnmower is level.
2. Remove oil dipstick from oil fill spout.
3. You receive a container of oil with the unit. Slowly
pour the entire container down the oil fill spout into the
engine.
NOTE: Initial oil fill requires only 14 oz. due to residual oil
in engine from the manufacturers 100% quality testing.
When changing oil you may need 16 oz.
4. Insert and tighten dipstick.
IMPORTANT:
• Check oil level before each use. Add oil if needed. Fill
to full line on dipstick.
• Changethe oilafter every 25 hours ofoperation oreach
season. You may need to change the oil more often un-
derdusty, dirtyconditions. See “TOCHANGEENGINE
OIL” in the Maintenance section of this manual.
ADD GASOLINE (See Fig. 7)
• Fill fuel tank to bottom of tank filler neck. Do not over-
fill. Use fresh, clean, regular unleaded gasoline with
a minimum of 87 octane. Do not mix oil with gasoline.
Purchase fuel in quantities that can be used within 30
days to assure fuel freshness.
CAUTION: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
GASOLINE
FILLER CAP
PRIMER
ENGINE OIL CAP
FIG. 7

8
MOWING TIPS
CAUTION: Do not use de-thatcher
blade attachments on your mower.
Such attachments are hazardous, will
damage your mower and could void
your warranty.
OPERATION
Alcohol blended fuels (called gasohol
or using ethanol or methanol) can at-
tractmoisturewhichleadsto separation
and formation of acids during storage.
Acidic gas can damage the fuel sys-
tem of an engine while in storage. To
avoidengine problems,the fuelsystem
should be emptied before storage of 30
days or longer. Empty the gas tank,
start the engine and let it run until the
fuellinesand carburetorareempty. Use
fresh fuel next season. See Storage
Instructions for additional information.
Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may occur.
TO STOP ENGINE
• To stop engine, release operator presence control bar.
TO START ENGINE (See Fig. 8)
NOTE: Due to protective coatings on the engine, a small
amount of smoke may be present during the initial use of
the product and should be considered normal.
• To start a cold engine, push primer three (3) times
before trying to start. Use a firm push. This step is not
usually necessary when starting an engine which has
already run for a few minutes.
• Hold operator presence control bar down to the handle
andpull starter handlequickly. Do notallow starter rope
to snap back.
NOTE: In cooler weather it may be necessary to repeat
priming steps. In warmer weather over priming may cause
flooding and engine will not start. If you do flood engine,
wait a few minutes before attempting to start and do not
repeat priming steps.
• Under certain conditions, such as very tall grass, it
may be necessary to raise the height of cut to reduce
pushing effort and to keep from overloading the engine
and leaving clumps of grass clippings. It may also be
necessary to reduce ground speed and/or run the lawn
mower over the area a second time.
• For extremely heavy cutting, reduce the width of cut
by overlapping previously cut path and mow slowly.
• For better grass bagging and most cutting conditions,
the engine speed should be set in the fast position.
• Poresin cloth grasscatchers can becomefilled with dirt
and dust with use and catchers will collect less grass.
To prevent this, regularly hose catcher off with water
and let dry before using.
• Keep top of engine around starter clear and clean of
grass clippings and chaff. This will help engine air flow
and extend engine life.
MULCHING MOWING TIPS
IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER
HOUSING FREE OF BUILT-UP GRASS AND TRASH. SEE
“CLEANING” IN THE MAINTENANCE SECTION OF THIS
MANUAL.
• The special mulching blade will recut the grass clip-
pings many times and reduce them in size so that as
they fall onto the lawn they will disperse into the grass
and not be noticed. Also, the mulched grass will biode-
grade quickly to provide nutrients for the lawn. Always
mulch with your highest engine (blade) speed as this
will provide the best recutting action of the blades.
• Avoid cutting your lawn when it is wet. Wet grass tends
to form clumps and interferes with the mulching action.
The best time to mow your lawn is the early afternoon.
At this time the grass has dried, yet the newly cut area
will not be exposed to direct sunlight.
• For best results, adjust the lawn mower cutting height
so that the lawn mower cuts off only the top one-third
of the grass blades (See Fig. 9). If the lawn is over-
grown it will be necessary to raise the height of cut to
reduce pushing effort and to keep from overloading
the engine and leaving clumps of mulched grass. For
extremely heavy mulching, reduce your width of cut by
overlapping previously cut path and mow slowly.
• Certaintypes ofgrassand grassconditions mayrequire
that an area be mulched a second time to completely
hide the clippings. When doing a second cut, mow
across (perpendicular) to the first cut path.
• Change your cutting pattern from week to week. Mow
north to south one week then change to east to west the
next week. This will help prevent matting and graining
of the lawn.
FIG. 9
MAX 1/3
FIG. 8
PRIMER
OPERATOR
PRESENCE
CONTROL BAR
STARTER
HANDLE

9
Check for Loose Fasteners
Clean / Inspect Grass Catcher *
Check Tires
Check Drive Wheels ***
Clean Lawn Mower ****
Clean under Drive Cover ***
Check Drive Belt / Pulleys ***
Check / Sharpen / Replace Blade
Lubrication
Clean and Recharge Battery **
Check Engine Oil level
Change Engine Oil
Clean Air Filter
Inspect Muffler
Replace Spark Plug
Replace Air Filter Paper Cartridge
Empty fuel system or add Stabilizer
BEFORE
EACH
USE
AFTER
EACH
USE
EVERY
10
HOURS
EVERY
25 HOURS
OR SEASON
EVERY
100
HOURS
BEFORE
STORAGE
1- Change more often if operating under a heavy load or in high outdoor temperatures.
2- Service more often if operating in dirty or dusty conditions.
3- Replace blades more often when mowing in sandy soil.
4- Charge 48 hours at end of season.
5- And after each 5 hours of use.
(if so equipped)
Electric-Start mowers
Power-Propelled mowers
Use a scraper
to clean under deck
*
**
***
****
MAINTENANCE
LUBRICATION CHART
GENERAL RECOMMENDATIONS
The warranty on this lawn mower does not cover items that
have been subjected to operator abuse or negligence. To
receive full value from the warranty, operator must maintain
mower as instructed in this manual.
Some adjustments will need to be made periodically to
properly maintain your unit.
At least once a season, check to see if you should make
any of the adjustments described in the Service and Ad-
justments section of this manual.
• At least once a year, replace the spark plug, clean or
replace air filter element and check blade for wear. A
new spark plug and clean/new air filter element assure
proper air-fuel mixture and help your engine run better
and last longer.
• Follow the maintenance schedule in this manual.
BEFORE EACH USE
1. Check engine oil level.
2. Check for loose fasteners.
LUBRICATION
Keep unit well lubricated (See “LUBRICATION CHART”).
IMPORTANT: DO NOT OIL OR GREASE PLASTIC WHEEL
BEARINGS. VISCOUS LUBRICANTS WILL ATTRACT DUST
AND DIRT THAT WILL SHORTEN THE LIFE OF THE SELF-
LUBRICATING BEARINGS. IF YOU FEEL THEY MUST BE
LUBRICATED, USE ONLY A DRY, POWDERED GRAPHITE
TYPE LUBRICANT SPARINGLY.
➀SPRAY LUBRICANT
➁SEE “ENGINE” IN MAINTENANCE SECTION
➁ENGINE OIL
➀HANDLE BRACKET MOUNTING PINS
➀REAR DOOR HINGE
➀MULCHER
DOOR
HINGE PIN
➀WHEEL
ADJUSTER
(ON EACH
WHEEL)

10
LAWN MOWER
Always observe safety rules when performing mainte-
nance.
TIRES
• Keep tires free of gasoline, oil, or insect control chem-
icals which can harm rubber.
• Avoid stumps, stones, deep ruts, sharp objects and
other hazards that may cause tire damage.
BLADE CARE
For best results, mower blade must be kept sharp. Replace
bent or damaged blades.
CAUTION: Use only a replacement
blade approved by the manufacturer
of your mower. Using a blade not ap-
proved by the manufacturer of your
mower is hazardous, could damage
your mower and void your warranty.
TO REMOVE BLADE (See Fig. 10)
1. Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with plug.
2. Turn lawn mower on its side. Make sure air filter and
carburetor are up.
3. Use a wood block between blade and mower housing
to prevent blade from turning when removing blade
bolt.
NOTE: Protect your hands with gloves and/or wrap blade
with heavy cloth.
4. Remove blade bolt by turning counter-clockwise.
5. Remove blade and attaching hardware (bolt, lock
washer and hardened washer).
NOTE: Removethe bladeadapter andcheck the key inside
hub of blade adapter. The key must be in good condition
to work properly. Replace adapter if damaged.
TO REPLACE BLADE (See Fig. 10)
1. Position the blade adapter on the engine crankshaft.
Be sure key in adapter and crankshaft keyway are
aligned.
2. Position the blade on the blade adapter aligning the
two (2) holes in the blade with the raised lugs on the
adapter.
3. Besure thetrailing edgeof blade (opposite sharp edge)
is up toward the engine.
4. Installthe blade boltwith the lockwasher and hardened
washer into blade adapter and crankshaft.
5. Useblockof woodbetweenbladeandlawnmower hous-
ing and tighten the blade bolt, turning clockwise.
• The recommended tightening torque is 35-40 ft. lbs.
IMPORTANT: BLADEBOLTISHEATTREATED. IFBOLTNEEDS
REPLACING,REPLACE ONLYWITHAPPROVED BOLTSHOWN
IN THE REPAIR PARTS SECTION OF THIS MANUAL.
TO SHARPEN BLADE
NOTE: We do not recommend sharpening blade - but if you
do, be sure the blade is balanced. An unbalanced blade
will cause eventual damage to lawn mower or engine.
MAINTENANCE
FIG. 10
BLADE
BOLT HARDENED
WASHER
LOCK
WASHER
BLADE ADAPTER KEY
BLADE
TRAILING EDGE
CRANKSHAFT
KEYWAY
CRANKSHAFT
• The blade can be sharpened with a file or on a grind-
ing wheel. Do not attempt to sharpen while on the
mower.
• To check blade balance, drive a nail into a beam or
wall. Leave about one inch of the straight nail exposed.
Place center hole of blade over the head of the nail.
If blade is balanced, it should remain in a horizontal
position. If either end of the blade moves downward,
sharpen the heavy end until the blade is balanced.
GRASS CATCHER
• The grass catcher may be hosed with water, but must
be dry when used.
• Check your grass catcher often for damage or dete-
rioration. Through normal use it will wear. If catcher
needs replacing, replace only with approved replace-
ment catcher shown in the Repair Parts section of this
manual. Give the mower model number when order-
ing.
ENGINE
LUBRICATION
Use only high quality detergent oil rated with API service
classification SG–SL. Select the oil's SAE viscosity grade
according to your expected operating temperature.
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)
improve starting in cold weather, these multi-viscosity oils
will result in increased oil consumption when used above
32°F. Check your engine oil level more frequently to avoid
possible engine damage from running low on oil.
Change the oil after every 25 hours of operation or at least
once a year if the lawn mower is not used for 25 hours in
one year.
Check the crankcase oil level before starting the engine
and after each five (5) hours of continuous use. Tighten oil
plug securely each time you check the oil level.
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
SAE VISCOSITY GRADES
-20 0 30 40 80 100
-30 -20 0 20 30 40
F
C
32
-10 10
60
5W-30
SAE 30

11
MAINTENANCE
TO CHANGE ENGINE OIL (See Fig. 11)
NOTE: Before tipping lawn mower to drain oil, empty fuel
tank by running engine until fuel tank is empty.
1. Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with plug.
2. Remove engine oil cap; lay aside on a clean surface.
3. Tip lawn mower on its side as shown and drain oil into
a suitable container. Rock lawn mower back and forth
to remove any oil trapped inside of engine.
CONTAINER
FIG. 11
4. Wipe off any spilled oil from lawn mower or side of
engine.
5. Slowly pour oil down the oil fill spout, stopping every
few ounces to check the oil level with the dipstick.
6. Stop adding oil when you reach the FULL mark on the
dipstick. Wait a minute to allow oil to settle.
7. Continue adding small amounts of oil, rechecking the
dipstick until oil level settles at FULL. DO NOT over-
fill, or engine will smoke heavily from the muffler on
startup.
8. Always be sure to retighten oil dipstick before starting
engine.
9. Reconnect spark plug wire to spark plug.
AIR FILTER (See Fig. 12)
Your engine will not run properly and may be damaged by
usinga dirtyair filter. Replacethe airfilter every100 hours of
operation or every season, whichever occurs first. Service
air cleaner more often under dusty conditions.
TO CLEAN AIR FILTER
1. Remove cover.
2. Carefully remove cartridge.
3. Clean by gently tapping on a flat surface. If very dirty,
replace cartridge.
CAUTION: Petroleumsolvents,such as
kerosene, are not to be used to clean
cartridge.Theymaycause deterioration
of the cartridge. Do not oil cartridge.
Do not use pressurized air to clean or
dry cartridge.
4. Install cartridge, then replace cover.
MUFFLER
Inspect and replace corroded muffler as it could create a
fire hazard and/or damage.
SPARK PLUG
Replacespark plug atthe beginningofeach mowingseason
or after every 100 hours of operation, whichever occurs
first. Spark plug type and gap setting are shown in the
“PRODUCT SPECIFICATIONS” section of this manual.
CLEANING
IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER
HOUSING FREE OF BUILT-UP GRASS AND TRASH. CLEAN
THE UNDERSIDE OF YOUR MOWER AFTER EACH USE.
CAUTION: Disconnect spark plug wire
from spark plug and place wire where it
cannot come in contact with plug.
• Clean the underside of your lawn mower by scraping
to remove build-up of grass and trash.
• Clean engine often to keep trash from accumulating. A
clogged engine runs hotter and shortens engine life.
• Keepfinishedsurfaces/wheelsfreeofallgasoline,oil,etc.
• We do not recommend using a garden hose to clean
lawn mower unless the electrical system, muffler, air
filter and carburetor are covered to keep water out.
Water in engine can result in shortened engine life.
CLEAN UNDER DRIVE COVER
Clean under drive cover at least twice a season. Scrape un-
dersideof coverwith puttyknife orsimilar toolto removeany
build-up of trash or grass on underside of drive cover.
CARTRIDIGE
FILTER COVER
SLOT
TAB
FIG. 11

12
MOWING
POSITION MOWING POSITION
HIGH POSITIONLOW POSITION
HANDLE
BRACKET
HAIRPIN
COTTER
MOUNTING
PIN
FIG. 14
LAWN MOWER
TO ADJUST CUTTING HEIGHT
See “TO ADJUST CUTTING HEIGHT” in the Operation
section of this manual.
REAR DEFLECTOR
The rear deflector, attached between the rear wheels of
your mower, is provided to minimize the possibility that
objects will be thrown out of the rear of the mower into
the operator's mowing position. If the deflector becomes
damaged, it should be replaced.
TO ADJUST HANDLE (See Figs. 13 thru 15)
The handle can be mounted in a high or low position. The
mounting holes in the bottom of lower handle are off center
for raising or lowering the handle.
1. Remove upper handle and all wire tie(s) securing
cable(s) to lower handle.
2. Remove hairpin cotters from lower handle bracket
mounting pin.
3. Squeeze lower handle in to remove it from mounting
pins.
4. Turn lower handle over to raise or lower handle.
5. Squeeze lower handle in and position holes onto
mounting pins on handle bracket.
6. Reassemble upper handle and all parts removed from
lower handle.
CAUTION: TO AVOID SERIOUS INJURY,
BEFOREPERFORMINGANYSERVICEOR
ADJUSTMENTS:
ENGINE
ENGINE SPEED
Your engine speed has been factory set. Do not attempt to
increase engine speed or it may result in personal injury. If
you believe that the engine is running too fast or too slow,
take your lawn mower to an authorized service center for
repair and adjustment.
CARBURETOR
Your carburetor is not adjustable. If your engine does not
operate properly due to suspected carburetor problems,
take your lawn mower to an authorized service center for
repair and/or adjustment.
IMPORTANT: NEVER TAMPER WITH THE ENGINE
GOVERNOR,WHICHISFACTORYSETFOR PROPER ENGINE
SPEED. OVERSPEEDINGTHEENGINEABOVETHEFACTORY
HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK
THE ENGINE-GOVERNED HIGH SPEED NEEDSADJUSTING,
CONTACTYOURNEARESTAUTHORIZEDSERVICECENTER,
WHICH HAS PROPER EQUIPMENT AND EXPERIENCE TO
MAKE ANY NECESSARY ADJUSTMENTS.
SERVICE AND ADJUSTMENTS
FIG. 13
LOWER HANDLE
HANDLE
BRACKET HAIRPIN COTTER
SQUEEZE
TO ADJUST
MOUNTING PIN
LOWER
HANDLE
ROTATE
FIG. 15
1. Release control bar and stop engine.
2. Make sure the blade and all moving parts have
completely stopped.
3. Disconnectspark plug wirefrom sparkplug and
placewhere itcannotcome incontact withplug.

13
Immediately prepare your lawn mower for storage at the end of the season or if the unit will not be used for 30 days or more.
STORAGE
FIG. 17
LOWER HANDLE
SQUEEZE
TO ADJUST
FIG. 16
MOWING
POSITION
OPERATOR
PRESENCE
CONTROL
BAR FOLD
FORWARD
FOR
STORAGE
LOWER
HANDLE
HANDLE
KNOB
UPPER
HANDLE
ENGINE
FUEL SYSTEM
IMPORTANT: ITISIMPORTANTTOPREVENTGUMDEPOSITS
FROM FORMING IN ESSENTIALFUEL SYSTEM PARTS SUCH
AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK
DURING STORAGE. ALCOHOL BLENDED FUELS (CALLED
GASOHOL OR USING ETHANOL OR METHANOL) CAN
ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND
FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS
CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE
IN STORAGE.
• Empty the fuel tank by starting the engine and letting
it run until the fuel lines and carburetor are empty.
• Never use engine or carburetor cleaner products in the
fuel tank or permanent damage may occur.
• Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in mini-
mizing the formation of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer container.
Run engine at least 10 minutes after adding stabilizer to
allow the stabilizer to reach the carburetor. Do not empty
the gas tank and carburetor if using fuel stabilizer.
ENGINE OIL
Drain oil (with engine warm) and replace with clean engine
oil. (See “ENGINE” in the Maintenance section of this
manual).
CYLINDER
1. Remove spark plug.
2. Pour one ounce (29 ml) of oil through spark plug hole
into cylinder.
3. Pull starter handle slowly a few times to distribute oil.
4. Replace with new spark plug.
OTHER
• Do not store gasoline from one season to another.
• Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
• If possible, store your unit indoors and cover it to give
protection from dust and dirt.
• Cover your unit with a suitable protective cover that
does not retain moisture. Do not use plastic. Plastic
cannotbreathe, whichallows condensationto form and
will cause your unit to rust.
IMPORTANT: NEVER COVER MOWER WHILE ENGINE AND
EXHAUST AREAS ARE STILL WARM.
CAUTION: Never store the lawn mower
with gasoline in the tank inside a build-
ing where fumes may reach an open
flameor spark. Allowthe engineto cool
before storing in any enclosure.
LAWN MOWER
When lawn mower is to be stored for a period of time, clean
it thoroughly, remove all dirt, grease, leaves, etc. Store in
a clean, dry area.
1. Clean entire lawn mower (See “CLEANING” in the
Maintenance section of this manual).
2. Lubricate as shown in the Maintenance section of this
manual.
3. Be sure that all nuts, bolts, screws, and pins are se-
curely fastened. Inspect moving parts for damage,
breakage and wear. Replace if necessary.
4. Touch up all rusted or chipped paint surfaces; sand
lightly before painting.
HANDLE (See Figs. 16 and 17)
You can fold your lawn mower handle for storage.
1. Squeeze the bottom ends of the lower handle toward
each other until the lower handle clears the handle
bracket, then move handle forward.
2. Loosen upper handle mounting bolts enough to allow
upper handle to be folded back.
IMPORTANT: WHEN FOLDING THE HANDLE FOR STORAGE
OR TRANSPORTATION, BE SURE TO FOLD THE HANDLE AS
SHOWN OR YOU MAY DAMAGE THE CONTROL CABLES.
• When setting up your handle from the storage position,
the lower handle will automatically lock into mowing
position.

14
Does not start 1. Dirty air filter. 1. Clean/replace air filter.
2. Out of fuel. 2. Fill fuel tank.
3. Stale fuel. 3. Empty fuel tank and refill tank with fresh,
clean gasoline.
4. Water in fuel. 4. Empty fuel tank and refill tank with fresh,
clean gasoline.
5. Spark plug wire is disconnected. 5. Connect wire to plug.
6. Bad spark plug. 6. Replace spark plug.
7. Loose blade or broken blade adapter. 7. Tighten blade bolt or replace blade adapter.
8. Control bar in released position. 8. Depress control bar to handle.
9. Control bar defective. 9. Replace control bar.
10. Fuel valve lever (if equipped) in OFF position. 10. Turn fuel valve lever to the ON position.
11. Weak battery (if equipped). 11. Charge battery.
12. Disconnected battery connector (if equipped). 12. Connect battery to engine.
Loss of power 1. Rear of lawn mower housing or cutting 1. Raise cutting height.
blade dragging in heavy grass.
2. Cutting too much grass. 2. Raise cutting height.
3. Dirty air filter. 3. Clean/replace air filter.
4. Buildup of grass, leaves and trash under 4. Clean underside of mower housing.
mower.
5. Too much oil in engine. 5. Check oil level.
6. Walking speed too fast. 6. Cut at slower walking speed.
Poor cut – 1. Worn, bent or loose blade. 1. Replace blade. Tighten blade bolt.
uneven 2. Wheel heights uneven. 2. Set all wheels at same height.
3. Buildup of grass, leaves and trash under 3. Clean underside of mower housing.
mower.
Excessive 1. Worn, bent or loose blade. 1. Replace blade. Tighten blade bolt.
vibration 2. Bent engine crankshaft. 2. Contact a qualified service center.
Starter rope 1. Engine flywheel brake is on when control 1. Depress control bar to upper handle before
hard to pull bar is released. pulling starter rope.
2. Bent engine crankshaft. 2. Contact a qualified service center.
3. Blade adapter broken. 3. Replace blade adapter.
4. Blade dragging in grass. 4. Move lawn mower to cut grass or other
hard surface before starting.
Grass catcher 1. Cutting height too low. 1. Raise cutting height.
not filling 2. Lift on blade worn off. 2. Replace blade.
(if so equipped) 3. Catcher not venting air. 3. Clean grass catcher.
Hard to push 1. Grass is too high or wheel height is too low. 1. Raise cutting height.
2. Rear of lawn mower housing or cutting 2. Raise rear of lawn mower housing one (1)
blade dragging in heavy grass. setting higher.
3. Grass catcher too full. 3. Empty grass catcher.
4. Handle height position not right for you. 4. Adjust handle height to suit.
PROBLEM CAUSE CORRECTION
TROUBLESHOOTING POINTS

15
Consumer Wheeled Products - Limited Warranty
Husqvarna warrants to the original retail purchaser that this Husqvarna® product is free from defects in material or workmanship under normal use
and maintenance from the date of retail purchase for the applicable Warranty Period shown on Exhibit A. This Limited Warranty may not be transferred
to any subsequent purchaser of this Husqvarna® product. Certain components (e.g., engines and transmissions) are excluded from coverage, and other
limitations apply, as described in this document. Husqvarna will repair or replace at its discretion, any defective product or part covered by the Limited
Warranty, free of charge at any authorized Husqvarna Servicing Dealer/Center using original OEM Husqvarna replacement parts, subject to the
limitations and exclusions described below. Husqvarna does not offer an over-the-counter exchange program.
DISCLAIMERS, LIMITATIONS AND EXCLUSIONS
1. WARRANTY DISCLAIMER. THIS LIMITED WARRANTY IS THE SOLE EXPRESS WARRANTY PROVIDED BY HUSQVARNA AND THERE ARE NO
WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF, EXCEPT AS MAY BE PROVIDED BY LAW. THIS WARRANTY IS
GIVEN ONLY BY HUSQVARNA, AND MAY BE MODIFIED ONLY BY HUSQVARNA. THIS LIMITED WARRANTY IS THE FINAL EXPRESSION OF OUR
AGREEMENT, AND IS A COMPLETE AND EXCLUSIVE STATEMENT OF THE TERMS OF THAT AGREEMENT. THIS LIMITED WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY BASED ON LOCALITY
2. LIMITED DURATION. ANY WARRANTY THAT MAY BE IMPLIED BY LAW (INCLUDING ANY IMPLIED WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE OR USE AND IMPLIED WARRANTY OF MERCHANTABILITY) IS LIMITED TO THE DURATION OF THE APPLICABLE
WARRANTY PERIOD UNDER THIS LIMITED WARRANTY. SOME LOCALITIES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
3. EXCLUSIVE REMEDIES. SOME LOCALITIES, INCLUDING THE PROVINCE OF QUEBEC, DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
LIABILITY FOR INJURY TO PERSON OR FOR DAMAGES RESULTING FROM THE FAULT OF THE MANUFACTURER AND/OR THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. AS SUCH, SOME OF THE FOLLOWING LIMITATIONS MAY NOT APPLY TO YOU. THE
ABOVE REMEDIES ARE THE EXCLUSIVE REMEDIES FOR ANY BREACH OF THIS LIMITED WARRANTY. NO OTHER REMEDY, INCLUDING, BUT NOT
LIMITED TO ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES, FOR LOST PROFITS, LOST SALES, INJURY TO PERSON OR
PROPERTY, OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL LOSS SHALL BE AVAILABLE, AND ALL SUCH DAMAGES ARE HEREBY
DISCLAIMED.
4. Engines, Transmissions and certain other components are NOT covered. This Limited Warranty does not cover any of the following:
(a) Engines and Attachments.Except where otherwise indicated on Exhibit A, all Engines and Attachments are not covered by this Limited Warranty. In most cases, these
items are NOT manufactured by Husqvarna in which case they may be covered separately by their respective manufacturer's warranties if one is provided and included with
the product at the time of purchase. All such claims must be submitted and sent to the appropriate manufacturer or as otherwise directed in those separate warranties.
Husqvarna is not authorized to handle warranty adjustments or repairs on engines manufactured by Briggs & Stratton, Honda, Kawasaki, or Kohler (with the exception of
models equipped with LCT engines). Husqvarna does not assume any warranty obligation of the other manufacturers' engines under this Limited Warranty.
(b) Transmissions. Except where otherwise indicated on ExhibitA, Transmission / Transaxle (including Drive Systems) are not covered by this Limited Warranty. In most
cases, these items are NOT manufactured by Husqvarna in which case they may be covered separately by their respective manufacturer's warranties if one is provided and
included with the product at the time of purchase. The following transmission / transaxle manufacturers, Dana, Hydro-Gear, Tuff-Torq provide a warranty for the
transmission / transaxle to the ultimate purchaser or to Husqvarna. Husqvarna will assign the transmission / transaxle manufacturer's warranty or any rights thereof to the
original purchaser of the unit. To obtain transmission / transaxle warranty service, first contact the retailer who you purchased the unit from. Should you require assistance
or have any questions concerning transmission / transaxle warranty coverage, contact Husqvarna directly at our website www.husqvarna.com or call 800-487-5951 (US) or
800-805-5523 (Canada) for an authorized Husqvarna service provider. All such claims must be submitted and sent to the appropriate manufacturer or as otherwise directed
in those separate warranties. Husqvarna is not authorized to handle warranty adjustments or repairs on transmissions or transaxles. Husqvarna does not assume any
obligations under this Limited Warranty for the above listed manufacturers (for exceptions - see Exhibit A).
(c) Expendable Parts. This Limited Warranty does not cover general maintenance parts and items ("Expendable Parts"), including without limitation spark plugs, bulbs,
filters, lubricants, starter cords, belts, blades, and blade adapters.
(d) Emissions Control Components. This Limited Warranty does not cover Emissions control equipment and components to the extent regulated by the U.S. Environmental
Protection Agency or similar state, provincial or federal agencies. Such equipment and components are covered by a separate emission control warranty statement supplied
with your new product. Please consult this separate warranty statement for details.
5. Any COMMERCIAL, INSTITUTIONAL, AGRICULTURAL, INDUSTRIAL, INCOME PRODUCING, or RENTAL use will result in either
No Warranty or a Shortened Warranty Period. Depending on the product, there is either NO WARRANTY (whether statutory, contractual or
otherwise) or a reduced warranty if the product is used for commercial, institutional, agricultural, industrial, income producing, or rental purposes and, in
such circumstances, this Limited Warranty is offered instead of and replaces any warranty regime provided for by law. Please refer to Exhibit A.
6. Reconditioned or Refurbished Products have a 30 Day Limited Warranty. Under this Limited Warranty, Certified Factory Reconditioned or
Refurbished products have a 30 Day Limited Warranty for parts and labor for Non-Commercial Use. Products are only reconditioned at the Husqvarna
Factory.
7. Owner's (Your) Responsibilities. To preserve your rights under this Limited Warranty, you must exercise reasonable care and use of the product,
including, following the preventative maintenance, storage, fuel and oil usages as prescribed in the enclosed operator's manual. For example, the
following items are the Owner's responsibility and are not covered by this Limited Warranty:
a. Set-up and pre-delivery service, and engine tune-ups;
b. Adjustments after the first (30) thirty days of purchase and beyond, such as throttle cable, belt guides adjustments; and
c. Preventative maintenance as outlined in the operator's manual.
In addition, you must cease using the product immediately upon any failure or damage. The product should be taken to an authorized Husqvarna
servicing dealer prior to any further use.
8. Damages resulting from normal aging, wear and tear or neglect are NOT covered. The Limited Warranty does not cover damage other than
that resulting from defects in material or workmanship. The following are NOT considered defects in material or workmanship, and therefore are NOT
covered.

16
(a) Abrasion to mower decks;
(b) Tires damaged by external punctures;
(c) Natural discoloration of materials due to ultraviolet light;
(d) Damage to cutting equipment by way of contact with, rocks, or other non-approved materials and/or structures;
In addition, this Limited Warranty does not cover damages, malfunctions or failures resulting from abuse or neglect of the product related to or including
any of the following:
(e) Failure to provide or perform required maintenance services as prescribed in the operator's manual;
(f) Abuse, misuse, neglect, modifications, alterations, normal wear, improper servicing, use of unauthorized attachments, Lack of lubrication or
engine failure, due to the use of oils that do not meet Engine manufacturer's specifications;
(g) Use of gasohol, containing methanol (wood alcohol). Gasohol which contains a maximum 10% ethanol (grain alcohol) or 15% MTBE
(methyl/tertiary/butyl/ether) is approved;
(h) Use of ether or any starting fluids;
(i) Pressure cleaning or steam cleaning the product;
(j) Use of spark plugs other than those meeting emission performance requirements listed in the operator's manual;
(k) Tampering with engine speed governor or emission components, or running engines above specified and recommended engine speeds as
listed in your operator's manual;
(l) Operation of the unit with improperly installed/removed or modified cutting shields, guards, or safety devices;
(m) Any removed/damaged air filter, excessive dirt, abrasives, salt water, moisture, corrosion, rust, varnish, stale fuel, or any adverse reaction due
to incorrect storage procedures;
(n) Failures due to improper set up, pre-delivery service or repair service by anyone other than an authorized Husqvarna servicing dealer during
the warranty period;
(o) Dirt contaminated grease or oil, use of incorrect type of greases or oils, failure to comply with recommended greasing intervals, water or
moisture damage, and/or improper storage;
(p) Sprayers pumping or spraying caustic or flammable materials, lack of or broken strainers; or
(q) Continued use of product, after initial operational problem or failure occurs.
9. Reinforced Stamped (Armor Protected) 10 Year Limited & Fabricated Limited Lifetime, Deck Warranties. These Limited Warranties are for
the deck shell only – mechanical components/parts such as belts, pulleys, spindle housings, bearings, blades, rods, height adjusters, caster/anti scalp
wheels etc… are NOT covered. The Limited Lifetime Warranty does not cover damage other than that resulting from defects in material or
workmanship. The following are NOT considered defects in material or workmanship, and therefore are NOT covered:
(a) Abrasion to mower decks, including sand wear;
(b) Damage to cutting equipment by way of contact with, rocks, or other non-approved materials and/or structures;
(c) Rust and corrosion; and
(d) Natural discoloration of paint or other materials due to ultraviolet light.
HOW TO OBTAIN SERVICE
10. Authorized Husqvarna Servicing Dealer/Center. In order to obtain warranty coverage it is your responsibility (at your expense) to deliver or ship
your Husqvarna unit to an authorized Husqvarna Servicing Dealer/Center and arrange for pick-up or return of your unit after the repairs have been made.
If you do not know the location of your nearest authorized Husqvarna Servicing Dealer, call Husqvarna, at 1-800-487-5951 during the hours of 8:00 AM
to 8:00 PM Eastern Standard Time, or visit www.husqvarna.com. Should you require assistance or have questions concerning this Limited Warranty, you
may contact us at 800-487-5951 (US) or 800-805-5523 (Canada) during the hours of 8:00 AM to 8:00 PM Eastern Standard Time or contact us through
the web at www.husqvarna.com.
11. Documentation Required. You must maintain and present Proof of purchase (including date, product model and, if applicable, engine serial
number) to an authorized Husqvarna Servicing Dealer for warranty service under this Limited Warranty. Proof of purchase rests solely with you.
Husqvarna encourages you to register your product online at www.usa.husqvarna.com (US & Canada) to help ensure, among other things, that you can
be notified of important product information. However, registering your product is not a condition of warranty service.
Husqvarna Professional Products, NA, Inc.
9335 Harris Corners Parkway, Suite 500, Charlotte, NC 28269
575 49 43-01 W 2012 IR

17
Consumer Wheeled Limited Warranty Chart 2012 Exhibit A
Consumer (personal,
household use only) Commercial (any commercial, professional, institutional, agricultural, or
income producing use, other than
Rental Use
)
Rental (any
rental usage)
Riding Lawn Tractors:
Frame, Chassis, Front Axle 5 Years No Warranty No Warranty
Engine* * * *
Transmission (if made by Husqvarna/Peerless) 3 Years No Warrant
y
No Warrant
y
Transmission (if third party)** ** ** **
XLS Models only - stamped deck shell. Armor
Protected Limited Warranty 10 Years No Warranty No Warranty
Fabricated Deck shell. Limited Lifetime Warranty *** No Warrant
y
No Warrant
y
Battery 1 Year Pro-rated No Warrant
y
No Warrant
y
Other Non-Expendable Components 3 Years No Warranty No Warranty
Engine* * * *
Transmission ** ** No Warranty No Warranty
RZ4623 (967009801 & 967009802)
RZ5426 (967003601 & 967003602) - stamped deck
shell. Armor Protected Limited Warranty 10 Years No Warranty No Warranty
Fabricated Deck shell. Limited Lifetime Warranty *** No Warrant
y
No Warrant
y
Battery 1 Year Pro-rated No Warrant
y
No Warrant
y
Other Non-Expendable Components 3 Years No Warranty No Warranty
Engine* * * *
Transmission ** ** ** **
MZ5424S & MZ5425S (967003901 & 25021) -
stamped deck shell. Armor Protected Limited
Warranty 10 Years No Warranty No Warranty
Fabricated Deck shell. Limited Lifetime Warranty *** No Warrant
y
No Warrant
y
Battery 1 Year Pro-rated No Warrant
y
No Warrant
y
Other Non-Expendable Components 3 Years 1 Year No Warranty
LE475 Edger, Tillers, Snow Throwers
Engine* * * *
Other Non-Expendable Components 2 Years 90 days 90 days
Tiller Tines *** No Warrant
y
No Warrant
y
Walk Behind Mowers, High Wheel Trimmer
Engine* * * *
Battery 1 Year Pro-rated No Warrant
y
No Warrant
y
Other Non-Expendable Components 3 Years No Warranty No Warranty
Hovering Trimmers
Engine* * * *
Other Non-Expendable Components 2 Years 1 Year 90 days
Front Mounted Deck Riders
Engine* * * *
Transmission 2 Years No Warranty No Warranty
Other Non-Expendable Components 2 Years No Warranty No Warranty
Cultivators
Battery 1 Year Pro-rated No Warranty No Warranty
Other Non-Expendable Components 2 Years No Warranty No Warranty
Pressure Washers
Model 5525PW:
Engine* * * *
Pump 2 Years No Warranty No Warranty
Other Non-Expendable Components 2 Years No Warranty No Warranty
Engine* * * *
Pump 2 Years 2 Years No Warranty
Other Non-Expendable Components 2 Years 2 Years No Warranty
Generators
Engine* * * *
Other Non-Expendable Components* *2 Years (2nd Year Parts
Only) *2 Years-1365GN (2nd Year Parts Only) No Warrant
y
Spreaders
Residential Zero Turn Mowers ( MZ & EZ )
All other Pressure Washers (6027PW, 9032PW, 1340PW)
Product/Com
p
onent
Residential Zero Turn Mowers ( RZ Only )

18
Consumer Wheeled Limited Warranty Chart 2012 Exhibit A
Consumer (personal,
household use only) Commercial (any commercial, professional, institutional, agricultural, or
income producing use, other than
Rental Use
)
Rental (any
rental usage)
Product/Com
p
onent
Spreader 1 Year 1 Year 1 Year
Robotic Mowers
Robotic Mower 2 Years 90 days 90 days
Battery 1 Year 1 Year 1 Year
Parts & Accessories (if purchased)
Accessories (e.g., grass catcher, bumper guard
accessories, etc. 1 Year No Warranty No Warranty
Parts (e.g., belts, blades, etc.) 30 days No Warranty No Warranty
Parts & Accessories (if replaced in Warranty Service)
Replacement parts and/or accessories provided
under this Limited Warranty are warranted only for
the BALANCE of the warranty period applicable to
the part or accessory that was replaced. See to left See to left See to left
Consumer Commercial Rental
Armor Protected Stamped Deck Shell Example Below Fabricated Deck Shell Example Below
Stamped Deck Shell below, NOT reinforced
*** "Limited Lifetime Warranty" on Tiller tines and Fabricated Deck shell is for the life of the product or 7 (seven) years after the last date of the
complete unit's final production, whichever comes first. Deck Shell replacement will be limited to a maximum of two (2) decks within the Limited
Lifetime Warranty.
** See reference 1 (b) of the warranty statement.
RZ - Two (2) Year Consumer warranty, parts & labor, with Hydro-Gear Distributor network.
EZ - One (1) Year Commercial warranty, parts & labor, with Husqvarna.
Two (2) Year Consumer warranty, parts & labor, with Hydro-Gear Distributor network.
MZ - Two (2) Year Commercial warranty, parts & labor, with Hydro-Gear Distributor network.
* See Separate Engine Manufacturer's or Manufacturer's warranty. LCT Engines on specific Snow Throwers & Tillers, warranty through
Husqvarna.
Armor Protected
Stamped Deck Shell
Reinforced area
No reinforced area

19
Cesymbole signale les pointsimportantsen
matière de sécurité. Il signifie - ATTENTION
!!!, SOYEZ PRUDENT !!! VOTRE SÉCURITÉ
EST EN JEU.
ATTENTION: Débranchez toujours le fil
de bougie d’allumage et pour prévenir
les démarrages accidentels, posez-le de
telle façon qu’il ne puisse pas entrer en
contact avec la bougie d’allumage lors de
l’installation,dutransport,desajustements
ou des réparations.
ATTENTION: Les gaz d’échappement
et certains composants des véhicules
contiennent ou émettent des produits
chimiques reconnus dangereux par l’État
de la Californie, parce que cancérigènes
ou tératogènes ou responsables d’autres
troubles de la reproduction.
ATTENTION:Lesbornes des batteries, ainsi
que toutes les bornes et leurs accessoires
contenant du plomb, des dérivés du plomb
oudesproduitschimiquesàbasedeplomb,
sont reconnus dangereux par l’État de la
Californie, parce que cancérigènes ou
tératogènes ou responsables d’autres
troubles de la reproduction. Lavez-vous
soigneusement les mains après les avoir
touchés.
ATTENTION:Le silencieuxetd’autrespièces
demoteurdeviennentextrêmementchauds
lors du fonctionnement et restent chauds
après que le moteur se soit arrêté. Pour
éviter des brûlures graves, restez loin de
ces zones.
vers l’opérateur. Arrêtez les lames lorsque vous passez sur
du gravillon.
•N’utilisez jamais la machine si les protections, les plateaux
et les autres dispositifs de sécurité ne sont pas en place.
• Consultez les instructions du producteur pour connaître
le mode correct de fonctionnement et d’installation des
accessoires. N’utilisez que les accessoires conseillés par le
producteur.
• Arrêtez les lames lorsque vous traversez des allées
gravillonnées, des trottoirs ou des rues.
• Arrêtez le moteur si vous devez laisser la machine, avant de
la nettoyer, de la réparer ou de l’inspecter.
• Arrêtez le moteur et attendez que les lames s’arrêtent
complètement avant d’enlever le bac de ramassage.
•Tondez uniquement avec la lumière du jour ou avec une
bonne lumière artificielle.
•N’utilisez pas la machine si vous êtes sous l’influence de
l’alcool ou des drogues.
• N’utilisez jamais la machine sur de l’herbe humide. Marchez
d’unpassûr:saisissezbienlapoignéeetmarchez;necourrez
jamais.
• Désengagez le mécanisme automoteur ou l’embrayage de
la transmission des tondeuses qui en possèdent un avant
de démarrer le moteur.
• Si la machine commence à vibrer de façon anormale, arrêtez
lemoteur et cherchez immédiatement la cause. Les vibrations
sont en général un signal d’alarme.
• Porteztoujours deslunettesde protectionavecdes déflecteurs
lorsque vous utilisez la machine.
II. FONCTIONNEMENT DANS LES PENTES
Les pentes sont souvent à l’origine de glissades ou de chutes
pouvant causer de graves blessures. Faites très attention au
cas de pentes. Si vous ne vous y sentez pas en sécurité sur les
pentes, ne tondez pas.
FAITES:
• Tondez parallèlement à la pente, jamais en montée ou en
descente. Faites très attention lorsque vous changez de
direction.
•Enlevez les obstacles tels que les pierres, les branches les
arbres, etc.
•Faites attention aux trous, aux ornières et aux irrégularités
du terrain. L’herbe haute peut cacher des obstacles.
NE FAITES PAS:
•Ne tondez pas près des douves, des fossés ou des remblais.
Vous pourriez perdre l’équilibre ou trébucher.
•Ne tondez pas de pentes trop rapides.
• Ne tondez pas l’herbe humide. Vous pourriez glisser.
III. ENFANTS
Des accidents dramatiques peuvent survenir si l’utilisateur ne
fait pas attention à la présence des enfants. Les enfants sont
fréquemment attirés par la machine et par la tonte de la pelouse.
Ne croyez jamais que les enfants restent à l’endroit où vous les
avez vu en dernier.
•Tenez les enfants en dehors de l’aire de tonte sous la
surveillance d’un adulte digne de confiance.
•Soyez vigilant et arrêtez la machine si un enfant pénètre
dans l’aire de tonte.
•Avant de reculer et lorsque vous reculez regardez toujours
vers le bas et derrière s’il y a des enfants en bas âge.
•N’autorisez jamais les enfants à utiliser la machine.
•Soyez particulièrement prudents lorsque vous approchez
des angles morts, des buissons, des arbres ou de tout objet
pouvant boucher la vision normale.
IV. MANIPULATION SÛRE DU CARBURANT
Manipulez le carburant avec beaucoup de précaution, car il est
très inflammable et ses vapeurs sont explosives.
• Eteignez les cigarettes, cigares, pipes et autre sources
d’incendie.
RÈGLES DE SÉCURITÉ
Conseils pour l’utilisation en toute sécurité des tondeuses
IMPORTANT: CETTE MACHINE COUPANTE EST CAPABLE D’AMPUTER LES MAINS, LES PIEDS ET DE PROJETER DES
OBJETS. L’INOBSERVATION DES RÈGLES DE SÉCURITÉ SUIVANTES PUET ETRE LA CAUSE DES BLESSURES SÉRIEUSES
ET ÉVENTUELLEMENT MORTELLES.
I. FONCTIONNEMENT GÉNÉRAL
• Il est impératif, avant de démarrer la machine, de lire et
de comprendre toutes les instructions présentes dans le/s
manuel/s d’utilisation et sur la machine. Bien connaître
les commandes et l’utilisation de la machine avant la
démarrer.
• Nemettez pas les mains ou lespiedsprès ou au-dessous des
parties rotatives. Restez loins de l’ouverture de la décharge
a tout temps.
• Seuls des adultes dignes de confiance connaissant les
instructions doivent être autorisés à utiliser la machine.
• Débarrassez l’aire de tonte des objets tels que les pierres,
les jouets, les fils métalliques, les os, les bâtons etc. Ces
objets peuvent être soulevés et projetés par la lame.
•Assurez-vous qu’il n’y a personne, en particulier ni
animaux domestiques ni enfants, dans l’aire de tonte avant
de commencer à tondre. Arrêtez la machine si quelqu’un
s’introduit dans l’aire de tonte.
•N’utilisez pas la machine avec les pieds nus ou en portant
des sandales ouvertes. Portez toujours des chaussures
adéquates.
•Ne faites pas reculer la machine à moins d’y être contraint.
Regardez toujours parterre et derrière vous avant de reculer.
• Nedirigezjamais l’évacuation dumatériauversles personnes.
Evitez de diriger l’évacuation du matériau vers un mur ou un
obstacle. Le matériau évacué risque de rebondir en arrière

20
RÈGLES DE SÉCURITÉ.........................................19-20
SPÉCIFICATIONS DU PRODUIT ................................ 20
RESPONSABILITÉS DU CLIENT ............................... 20
ASSEMBLAGE ............................................................ 21
UTILISATION. ......................................................... 22-25
GUIDE D'ENTRETIEN ................................................. 26
ENTRETIEN ...........................................................26-29
RÉVISIONS ET RÉGLAGES .................................30-31
ENTREPOSAGE..................................................... 31-32
GUIDE DE DÉPANNAGE ........................................... 33
GARANTIE..............................................................34-37
SOMMAIRE
FÉLICITATIONS pour votre achat d’une tondeuse à gazon . Elle
a été conçue, perfectionnée, et fabriquée pour assurer le bon
fonctionnement et la sûreté maximum.
Encas d’un problèmequevousne pouvez pasrésoudre,contactez
le centre d’entretien autorisé le plus proche. Vous y trouverez
les techniciens qualifiés et les outils appropriés pour l’entretien
et la réparation de cette machine.
Veuillez lire et conserver ce manuel. Les instructions qu’il
contient vous permettront de monter, et d’entretenir correctement
votre tondeuse à gazon. Observez toujours les “RÈGLES DE
SÉCURITÉ”.
NUMÉRO
DE SÉRIE: ____________________________________
DATE D’ACHAT: ________________________________
LESNUMÉROSDESÉRIEETDEMODÈLESERONTSITUÉS
SUR LA DÉCALCOMANIE COLLÉE SUR L’ARRIÈRE DU
BOÎTIER DE TONDEUSE.
VOUS DEVRIEZ NOTER CES NUMÉROS-CI ET LA DATE
D’ACHAT. CONSERVEZ-LES POUR LA RÉFÉRENCE
D’AVENIR.
RESPONSABILITÉS DU CLIENT
• Lisez et faites attention aux règles de sécurité.
• Suivez un programme habituel d’entretien, de soin, et
d’utilisation de la tondeuse à gazon.
• Suivez les instructions dans les sections d'entretien et
d’entreposage de ce manuel de propriétaire.
• N’utilisez qu’un bidon homologué.
• N’enlevezjamaislebouchon et n’ajoutez jamais de carburant
lorsque le moteur est en marche. Laissez le moteur refroidir
avant de le remplir.
• Ne remplissez jamais le réservoir à l’intérieur.
• Ne rangez jamais ni l’appareil ni le bidon dans un endroit
où se trouve une flamme nue, des étincelles ou une flamme
pilote (chauffe-eau ou autres appareils).
• Ne remplissez jamais les bidons dans une voiture, un camion
ou une remorque revêtue de plastique. Placez toujours les
bidons sur le sol et à l’écart de votre véhicule avant le
remplissage.
• Sortez l’appareil à essence du camion ou de la remorque et
remplissez-le au sol. Si cela n’est pas possible, remplissez-
le avec un bidon portable plutôt qu’avec un distributeur à
pistolet.
• Laissez la buse au contact du bord de l’orifice du réservoir
d’essenceou du bidon pendant toute la duréeduremplissage.
N’utilisez pas de dispositif dont le pistolet se verrouille en
ouverture.
• Sivous versez du carburantsurvosvêtements,changez-vous
immédiatement.
• Ne remplissez jamais trop le réservoir. Remettez le bouchon
en place et serrez bien.
V. ENTRETIEN GÉNÉRALE
•Nefaitesjamaismarcherla tondeuse à l’intérieur d’un espace
clos.
•Ne faites ni réglage ni réparation avec le moteur en marche.
Débranchez le fil de la bougie et éloignez-le de la bougie
pour éviter les démarrages accidentels
•Les boulons et les écrous, et surtout les boulons qui servent
à fixer la lame, doivent être toujours correctement serrés.
Conservez la machine en bon état.
•N’altérez jamais le fonctionnement normal des dispositifs de
sécurité. Vérifiez régulièrement leur bon fonctionnement.
• Evitez que des herbes, des feuilles, ou des débris en tout
genre ne s’accumulent sur votre machine. Nettoyez les
éclaboussures d’huile ou d’essence. Laissez refroidir la
machine avant de l’entreposer.
•Dans le cas où vous heurtez un objet, arrêtez la machine et
vérifiez l’absence de dégâts. Avant de redémarrer, réparez
si nécessaire les dégâts.
• N’essayez jamais de régler la hauteur de la roue lorsque le
moteur est en marche.
• Les éléments du bac de ramassage s’usent et peuvent
s’abîmer et se détériorer, risquant ainsi de projeter les parties
en mouvement ou des objets. Contrôlez fréquemment ces
éléments et remplacez-les, en cas de besoin, par des pièces
de rechange conseillées par le fabricant.
• Les lames de la tondeuse sont affûtées et peuvent couper.
Enveloppez les lames ou portez des gants et faites très
attention lors des opérations d’entretien sur les lames.
• Ne changez pas le réglage du limiteur de régime et évitez
tout survitesse du moteur.
• Nettoyez ou remplacez au besoin les étiquettes
d’information.
AVERTISSEMENT: Ce tondeuse à gazon est équipé d’un moteur à combustion interne et il ne doit pas être utilisé
sur ou près d’un terrain couvert d’arbres, d’arbrisseaux, ou d’herbe si le système d’échappement n’est pas muni d’un
pare-étincelles qui rencontre les exigences des lois locales applicables. Quand un pare-étincelles est utilisé, il doit
être maintenu en bon état de fonctionnement par l’opérateur.
Un pare-étincelles pour le silencieux est disponible au centre d’entretien autorisé le plus proche.
SPÉCIFICATIONS DE PRODUIT
Capacité et le 1,6 Quarts de Gallon (1,8 Litre)
Type d’essence: L’essence sans Plomb Normale
Type d’huile SAE 30 (température + 32°F / 0°C)
(API SG–SL): SAE 5W30 (température – 32°F / 0°C)
Capacité d’huile: 20 Onces (0,58 Litre)
Bougie d’allumage: RC12YC (Écart: 0,030 po / 0,762 mm)
Couple de rotation
au boulon de lame: 35-40 ft.-lbs.