Husqvarna Fleet Services User manual

Husqvarna Fleet Services™ Machine Sensor
EN Operator's manual 2-10

Contents
Introduction..................................................................... 2
Safety..............................................................................4
Installation.......................................................................4
Operation........................................................................ 6
Maintenance................................................................... 7
Troubleshooting.............................................................. 9
Storage and disposal...................................................... 9
Technical data.............................................................. 10
Declaration of Conformity............................................. 10
Introduction
Introduction
This manual is a digital operator’s manual for the
Husqvarna Fleet Services™ Machine Sensor. For
more information, refer to the operator’s manual
included in the product carton. More information about
Husqvarna Fleet Services™ is also available on https://
fleetservices.husqvarna.com.
Support
For support about the product, speak to your Husqvarna
servicing dealer.
Product description
The Husqvarna Fleet Services™ Machine Sensor
collects and saves data from your Husqvarna product.
The Husqvarna Fleet Services™ Machine Sensor can
be attached on all Husqvarna handheld products and
lawn mowers. The data is saved and transmitted with
Bluetooth® wireless technology to the Husqvarna Fleet
Services™ app or the Husqvarna Fleet Gateway app.
The uploaded data shows the last known location of the
product, operation statistics and servicing history.
22132 - 001 - 19.10.2023

Product overview
1
2
3
4
5
6
78
9
10
1. Sensor top cover
2. Sensor circuit
3. Battery
4. Foam gasket
5. Rivet
6. Sensor bottom cover
7. Adhesive tape
8. Maintenance tool
9. Drill1
10. Rivet gun2
Symbols on the product
WARNING: Read and under-
stand the operator instructions
before you operate the prod-
uct.
This product complies with the applicable
EU Directives.
This product complies with the applicable
UK Directives.
It is not permitted to dispose the product
as usual domestic waste. Obey national
regulations and use the local recycling
system.
The product agrees with applicable
UkrSEPRO directives.
1Not included.
2Not included.
2132 - 001 - 19.10.2023 3

The product agrees with applicable RCM
directives. Applies to AU/NZ only.
Safety
Safety definitions
Warnings, cautions and notes are used to point out
specially important parts of the manual.
WARNING: Used if there is a risk of
injury or death for the operator or bystanders
if the instructions in the manual are not
obeyed.
CAUTION: Used if there is a risk of
damage to the product, other materials or
the adjacent area if the instructions in the
manual are not obeyed.
Note: Used to give more information that is necessary
in a given situation.
Safety instructions for operation
WARNING: Read the warning
instructions that follow before you use the
product.
• Follow the instructions about how to operate the
product. Refer to Operation on page 6 .
• Use the product with the compatible Husqvarna
products. Speak to your Husqvarna representative
for more information.
• Do not make modifications on the product.
• Do not use the product in dangerous environments
or near flammable material.
• Do not use the product if it is damaged. If the
product is damaged, it can become too hot and
increase the risk of fire.
Safety instructions for maintenance
WARNING: Read the warning
instructions that follow before you use the
product.
• Water leakage can cause electrical shock or fire.
Make sure that you do maintenance on the product
in a dry area.
• Follow the instructions about how to do maintenance
on the product. Refer to
Maintenance on page 7 .
Battery safety
WARNING: Read the warning
instructions that follow before you use the
product.
• Only use original batteries that Husqvarna
recommends for your product. Refer to Technical
data on page 10 .
• Keep the battery away from children.
• Keep the battery away from sunlight, heat or open
flame. The battery can cause an explosion and
cause burns and/or chemical burns.
• Keep the battery away from rain and wet conditions.
• Do not try to disassemble or break the battery.
• Do not do modifications to the battery.
• Do not use a damaged battery.
• Do not keep the battery in ambient temperatures that
are more than 65°C/149°F.
• Do not use the product if the battery compartment
does not close tightly.
Installation
To prepare for the installation of the
Husqvarna Fleet Services™ Machine
Sensor
1. Install the battery. Refer to To replace the battery on
page 7
.
2. Download the Husqvarna Fleet Services™ app or
the Husqvarna Fleet Gateway app on your mobile
device.
3. Log on to the app.
4. Do a pairing operation. Refer to To do a pairing
operation with a product on page 4 .
To do a pairing operation with a
product
1. Make sure that your mobile device has Wi-Fi
connection and that Bluetooth® wireless technology
is enabled on your mobile device.
2. Open the Husqvarna Fleet Services™ app or the
Husqvarna Fleet Gateway app on your mobile
device.
42132 - 001 - 19.10.2023

3. Select Layers .
4. Select the product that is to be used with the
Husqvarna Fleet Services™ Machine Sensor.
5. Select
Install sensor > Scan QR code > Approve .
6. Scan the QR code on the sensor circuit with your
mobile device.
To examine where to install the
Husqvarna Fleet Services™ Machine
Sensor
CAUTION: Do not install the Husqvarna
Fleet Services™ Machine Sensor on the
product where it prevents the product to
operate correctly.
Note: For battery operated products, the LED
indicator on the sensor circuit must flash when the
product operates on full and low clutch.
1. Do a pairing operation. Refer to To do a pairing
operation with a product on page 4
.
2. Start the product.
3. Hold the Husqvarna Fleet Services™ Machine
Sensor near the product to find the electromagnetic
field. Make sure that the LED indicator on the sensor
circuit flashes one time each second.
CAUTION: Do not put your hands
on the antenna of the sensor. Hold the
sensor by the bottom cover.
4. Examine that there is sufficient space to install the
sensor bottom cover on the product. Use a pair
of pliers to remove the outer holes on the sensor
bottom cover if it is necessary.
To install the Husqvarna Fleet
Services™ Machine Sensor on a
product
1. Examine where to install the Husqvarna Fleet
Services™ Machine Sensor. Refer to
To examine
where to install the Husqvarna Fleet Services™
Machine Sensor on page 5 .
2. Attach the adhesive tape on the sensor bottom
cover.
3. Attach the sensor bottom cover on a flat and clean
surface on the product.
4. Drill 2 holes that are 4 mm/0.2 in. in diameter.
2132 - 001 - 19.10.2023 5

CAUTION: Use a drill stop or
disassemble the product to prevent
damage to the product.
5. Put the 2 rivets into the 2 holes and install the rivets
with a rivet gun.
6. Put the sensor circuit with the foam gasket into the
sensor bottom cover. Align the white mark on the
sensor with the mark on the sensor bottom cover.
7. Use the point of the maintenance tool to carefully
push the foam gasket into position in the sensor
bottom cover.
CAUTION: Do not push the center
of the sensor circuit.
8. Attach the sensor top cover on the sensor bottom
cover clockwise with the maintenance tool.
Note: Husqvarna recommends you to attach a decal
on the product with the name of the product. This makes
it easier to identify the product in the Husqvarna Fleet
Services™ app or the Husqvarna Fleet Gateway app.
Note: You can find more information about how to
install the Husqvarna Fleet Services™ Machine Sensor
in the Husqvarna Fleet Services™ app or the Husqvarna
Fleet Gateway app.
Operation
LED indicator of the sensor
LED Operation
LED is on for 1 second. The Husqvarna Fleet Services™ Machine Sensor restarts before it con-
nects to the Husqvarna Fleet Services™ app or the Husqvarna Fleet Gate-
way app.
LED flashes 2 times each second. The Husqvarna Fleet Services™ Machine Sensor is connected to the
Husqvarna Fleet Services™ app or the Husqvarna Fleet Gateway app.
62132 - 001 - 19.10.2023

LED Operation
LED flashes 1 time each 5 seconds. The Husqvarna Fleet Services™ Machine Sensor is enabled and has up-
loaded all available data.
LED flashes 2 times each 5 seconds. The Husqvarna Fleet Services™ Machine Sensor is enabled and uploads
data.
LED flashes 1 time each second. The sensor has found an electromagnetic field from a battery operated
product or electric component.
LED flashes regularly. The amount of
flashes from the LED changes with the
speed of the engine.
The sensor senses the speed of the petrol operated product.
LED is on for 1 second, then it goes off
and comes on again.
Firmware updates.
LED is on for 1 second, then it goes off
for 5 seconds and comes on again.
The sensor has found the engine/motor of the product and the configura-
tion is set.
Operation of the product
• The Husqvarna Fleet Services™ Machine Sensor
connects to the Husqvarna Fleet Services™ app or
the Husqvarna Fleet Gateway app automatically.
The Husqvarna Fleet Services™ Machine Sensor
connects to the app with Bluetooth® wireless
technology.
• The Husqvarna Fleet Services™ app automatically
collects data from the Husqvarna Fleet Services™
Machine Sensor.
• The data update shows in the Husqvarna Fleet
Services™ app approximately 15 minutes after the
product is set to off.
• The Husqvarna Fleet Services™ Machine Sensor
can save data for maximum 3 weeks of operation
time.
• Husqvarna recommends to upload the data
minimum 1 time each week for products that are in
operation regularly.
Maintenance
To replace the battery
WARNING: Read and understand the
battery safety before you install the battery.
Refer to
Battery safety on page 4 .
1. Remove the sensor top cover from the sensor
bottom cover counterclockwise with the maintenance
tool.
2132 - 001 - 19.10.2023 7

2. Remove the sensor circuit from the sensor bottom
cover.
3. Remove the battery from the sensor circuit and
recycle it.
4. Install a new battery. Make sure that the "+" sign of
the battery is put on the "+" sign in the sensor circuit.
5. Make sure that the indicator on the sensor circuit
flashes green.
6. Put the sensor circuit in the foam gasket.
7. Put the sensor circuit with the foam gasket into the
sensor bottom cover.
8. Use the point of the maintenance tool to carefully
push the foam gasket into position in the sensor
bottom cover.
CAUTION: Do not push the center
of the sensor circuit.
9. Attach the sensor top cover on the sensor bottom
cover clockwise with the maintenance tool.
82132 - 001 - 19.10.2023

Troubleshooting
Troubleshooting
If the Husqvarna Fleet Services™ Machine Sensor does not operate as usual, follow the table below. Speak to your
Husqvarna servicing dealer if you cannot find the cause of the fault.
Symptom Cause Solution
The LED of the Husqvarna
Fleet Services™ Machine Sen-
sor is not on.
The light is too low for the light sensor. Put the Husqvarna Fleet Services™ Ma-
chine Sensor in an area that has good
light.
The battery is empty. Replace the battery. Refer to To replace
the battery on page 7 .
The data of the Husqvarna Fleet Serv-
ices™ Machine Sensor updates.
Wait approximately 15 minutes for the
data to update.
The Husqvarna Fleet Services™ Ma-
chine Sensor has not found an electri-
cal field.
Move the Husqvarna Fleet Services™
Machine Sensor near the product until
the light comes on.
The LED of the Husqvarna
Fleet Services™ Machine Sen-
sor flashes 3 times each 3
seconds. The Husqvarna Fleet
Services™ Machine Sensor
does not collect data.
The internal clock of Husqvarna Fleet
Services™ Machine Sensor is not set.
Hold the mobile device with the Husqvar-
na Fleet Services™ app near the Husq-
varna Fleet Services™ Machine Sensor
to update the time.
No data is received from the
Husqvarna Fleet Services™
Machine Sensor.
The data of the Husqvarna Fleet Serv-
ices™ Machine Sensor updates.
Restart the Husqvarna Fleet Services™
app or the Husqvarna Fleet Gateway
app. Wait approximately 15 minutes for
the data to update.
"Status unknown" is shown
in the Husqvarna Fleet Serv-
ices™ app or the Husqvarna
Fleet Gateway app.
The Husqvarna Fleet Services™ Ma-
chine Sensor is not reset correctly.
Reset the Husqvarna Fleet Services™
Machine Sensor. Refer to To reset the
Husqvarna Fleet Services™ Machine
Sensor on page 9 .
To reset the Husqvarna Fleet
Services™ Machine Sensor
1. Make sure that the correct product is selected in the
Husqvarna Fleet Services™ app or the Husqvarna
Fleet Gateway app.
2. Remove the battery and wait 30 seconds before you
install the battery again. Refer to
To replace the
battery on page 7
.
3. Make sure that the Husqvarna Fleet Services™
Machine Sensor is connected to the Husqvarna
Fleet Services™ app or the Husqvarna Fleet
Gateway app.
4. Operate the product for a minimum of 30 seconds.
Storage and disposal
To put the product in storage
• Put the product in storage in a dry, closed and frost-
free area where the temperature is between 5°C/
41°F and 25°C/77°F.
Disposal
• Obey national regulations.
• Use the local recycling system.
2132 - 001 - 19.10.2023 9

• The product and battery are not domestic waste. For
more information, speak to your Husqvarna dealer.
Technical data
Technical data
Husqvarna Fleet Services™ Machine Sensor
Modulation MSK
Nominal input V 3.0
Max. input V 3.4
Min. input V 2.6
Internal operation maximum temperature °C/°F 55/131
Internal operation minimum temperature °C/°F -10/14
Absolute maximum temperature °C/°F 60/140
Absolute minimum temperature °C/°F -20/-4
Nominal RF range m/ft 20/66
Receiver type Category 2
Transmitter type Category 2
Nominal RF output power dBm 0
Frequency range MHz 2402-2480
Max. current consumption mA 24
Battery VARTA CR2450
Functionality Petrol: Pulse engine tachometer (500-15K rmp) nominal sen-
sitivity of 10 cm/4 in. in line of sight from source.
Battery: Motor-on chronometer nominal sensitivity of 10 cm/ 4
in. in line of sight from source.
Offline data storage of 100 operated hours.
Nearby operator tag detection.
Nominal 120 KB of data each operated hour.
Sensors rmp tachometer
Internal temperature (± 4°C/39°F)
Battery status
Declaration of Conformity
Declaration of conformity
Refer to www.husqvarna.com/doc for the declaration of
conformity.
10 2132 - 001 - 19.10.2023

2132 - 001 - 19.10.2023 11

www.husqvarna.com
Original instructions
1141823-26
2023-10-19