Huviron SK-B280 User manual

Before calling service, check the following points for
possible misuse.
If you can't correct the problem after going through
this chart, contact a service professional for further
assistance.
1. Manual iris lens
2. Auto iris lens
1) Before mounting a lens, please check whether
it is a C mount or CS mount lens.
2) CS mount lens : After removing the protective
rubber, attach the lens.
3) C mount lens : Before installing the lens, attach
the C mount ring to the camera.
4) Set the LENS mode to "manual" by OSD.
1) Attach a DC lens as like the manual lens connection.
2) Connect the lens plugto the auto iris lens connector
on the rear panel of the camera.
3) Set the LENS mode to DC and adjust DC level
by OSD.
※The lens is not supplied with this camera.
1. This camera supports supreme resolution(650TVL).
1. Do not install the camera outdoors.
Use weatherproof housing for outdoor.
2. Choose an ideal location for the camera, since the
camera unit must be protected against moisture
and vibration.
3. Be careful not to scratch the camera unit, especially
lens glass.
4. Use the camera under proper temperature.
(-10°C ~ +50°C)
5. Handle with care. Dropping it can cause serious
damage to the camera.
6. Avoid any direct sun light into the lens.
7. Use the adaptor regulated 12V DC, 300mA.
1. Remove the protective rubber before installing a
CS mount lens.(If you use a C mount lens, add a
C mount ring.-option)
2. Connect the video output jack to the monitor video
in jack.
3. Connect power supply. Check the voltage.
2. You can adjust all functions by OSD.
3. This camera has "non-polarity" function.
You can connect 12V DC regardless polarity.
4. Practical small size.
C-MOUNT RING(option)
CS-MOUNT
51
1/4" -20UNC
30.5
MINI BOX CAMERA
SK-B280
MANUAL
36.5
FEATURES
CAUTION AND WARNING
DESCRIPTION OF OPERATION
ACCESSORIES
LENS CONNECTION DIMENSION
TROUBLESHOOTING GUIDE
C MOUNT RING -(option)
DC-TYPE
① DAMP COIL -
② DAMP COIL +
③ DRIVE COIL +
④ DRIVE COIL -
AUTO IRIS LENS
CONNECTOR
①
②
③
④
OVERVIEW
Mouting hole
±
1/4"-20UNC(20THREAD)
L : 4.5mm 0.2mm(ISO standard)
①Video output :
Power input terminal :
Menu setup jog lever :
Used to connect the video monitor.
Used to connect a 12V DC power supply only.
(Non-polarity)
: Used to access the menu and confirm
selection.
: Used to move the cursor to up or
down.
t : Used to move the cursor to left
or right and change the value.
ㆍENTER
ㆍUp, Down
ㆍLeft, Righ
②
③
①
②③
If the product is to be put out of operation definitively,
take it to a local recycling plant for a disposal which
is not harmful to the environment.
Problem Check point
Too dark or bright
picture
No Power
Poor picture quality
Shrinking picture
Readjust the contrast or brightness
controls on the monitor.
Clean the camera lens.
Readjust lens focus.
Check the condition of the power
sources.
Check for power connection.

SPECIFICATON
※AII specification is subject to change without notice to improve the quality.
768(H) x 494(V) Pixel(NTSC)
752(H) x 582(V) Pixel(PAL)
6.35㎛(H) x 7.4㎛(V) (NTSC)
6.5㎛(H) x 6.25㎛(V) (PAL)
1/3" SONY SUPER HAD CCDⅡ
Model No.
Image Sensor
Effective Pixel
Cell Size
Sync. Type
Resolution
S/N
Video Output
Gamma
OSD
White Balance
Shutter Speed
Sense up
Backlight
AGC
DNR(3D)
Privacy Zone
Mirror
Day & Night
Lens
Power Supply
Dimension
Weight
SK-B280
2:1 Interlace
Internal
Color : 650 TV-Line, B/W : 720 TV-Line
52dB or More(AGC OFF)
1.0 Vp-p(Sync. Negative) Termination 75Ω
0.1Lux(F/1.2), 0.0001Lux(Sense up)
γ= 0.45 typ.(0.2 ~ 1.0)
Yes(Multi Language)
ATW(2,500 ~ 9,500 )/MANUAL/AWC
1/60(1/50) ~ 1/100,000sec
Auto(Selectable limit 2X~1024X)/FIXED/OFF
OFF/BLC/HLC/DWDR
LOW/MIDDLE/HIGH/OFF
AUTO/LOW/MIDDLE/HIGH/OFF
ON/OFF(4 Zone)
ON/OFF(8 Zone)
ON/OFF
Electronic D&N
AUTO/OFF
CS Mount
Regulated DC 12V ±10%
Max. 120mA(at 12V DC)
-10℃ ~ 50℃
-20℃ ~ 60℃
36.5mm(W) x 36.5mm(H) x 51mm(L)
Approx. 100g
Scanning
System
Motion
Detection
Blemish
Compensation
Current
Consumption
Operation
Temp.
Preservation
Temp.
Min.
Illumination
MIRROR
SHARPNESS
GAMMA
LSC
RETURN
MOTION
AREA
SENSITIVITY
DISPLAY
HOLD TIME
RETURN
MASK 1~8
RETURN
LANGUAGE
TITLE
COMMUNICATION
(N/A)
DPC
FACTORY SET
RETURN
SAVE AND EXIT
EXIT
RETURN
5. MOTION
6. PRIVACY
7. SPECIAL
8. EXIT
MIRROR, OFF
0~30
0.45, 0.55, 0.65
USER
ON
OFF
ON, OFF
AREA 1~4
RETURN
1~30
0~15
ON, OFF
OFF
ON
OFF--ON
OFF--ON
OFF
AUTO
YES, NO
GAMMA
RETURN
SET LEVEL
RETURN
TOP
BOTTOM
LEFT
RIGHT
RETURN
DOT SEL
DOT XY
MOVE XY
COLOR
RETURN
EDIT
RESET
POSITION
RETURN
ID
BAUDRATE
PROTOCOL
RETURN
WHITE THR
LUMA THR
RETURN
Set a vertical image inversion
Sharpness adjustable
Set a gamma value
0.20, 0.25, 0.30, 0.35, 0.40, 0.45, 0.50, 0.55, 0.60, 0.65,
0.70, 0.75,0.80, 0.85, 0.90, 0.95, 1.00 : Gamma adjustable
Move back to previous menu
0~30 : Use the LSC and level adjustable
Move back to previous menu
LSC OFF
Move back to previous menu
Motion detection function activate/deactivate
0~143
2~145
0~190
2~192
Move back to previous menu
Move back to previous menu
Motion detection sensitivity
Select notification method of motion detection
Set the duration of alarm out
Alarm ON/OFF
Move back to previous menu
Display each privacy mask or not
L_TOP, L_BOT, R_BOT, R_TOP : Determines which of
the 4 vertices of each MD area is to be used
ENTER SETTING : Determines the coordinate
ENTER SETTING : Move the mask
BLACK, WHITE, … : Select mask color(8 colors)
Move back to previous menu
Move back to previous menu
ENGLISH, … : Select language(9 languages)
Display the camera name on the screen
Camera name reset
Camera name position
Move back to previous menu
1~255 :Select thecamera ID for RS-485 communication
2400, 4800, 9600 : Select baud rate
PELCO-D : Camera protocol
Move back to previous menu
Deactivates Defect Pixel Correction in low illumination
0~255 : Setup the limited value of white pixel correction
0~255 : Setup the limited value of white pixel correction
Move back to previous menu
Reset your camera to factory default condition
Return to previous menu
(Communication setting is not changed)
Save the value and exit menu
Escape the menu without save
Move back to previous menu
4. IMAGE ADJUST
ALARM OUTPUT
OFF, MESSAGE, TRACE
Make a zone for motion detection
1. EXPOSURE
3. DAY&NIGHT
LENS
AGC
SENSE-UP
BACKLIGHT
3D-DNR
RETURN
AWB MODE
R-Y GAIN
B-Y GAIN
RETURN
D&N MODE
BURST
C_SUP
A_SUP
SMART IR
RETURN
MANUAL
DC
BLC
HLC
D-WDR
ATW
MANUAL
PUSH
0~255
0~255
AUTO
AUTO-CDS
(N/A)
COLOR
B&W
EXT
ON, OFF
0~100
0~100
ON, OFF
BRIGHTNESS
E. SHUTTER
BRIGHTNESS
E. SHUTTER
BLC LEVEL
TOP
BOTTOM
LEFT
RIGHT
HBLC
MODE
HLC LEVEL
MASK 1~4
SET LEVEL
M-WR
M-WB
RETURN
DAY→NIGHT
NIGHT→DAY
DELAY TIME
RETURN
A. DAY→NIGHT
A. NIGHT→DAY
C. DAY→NIGHT
C. NIGHT→DAY
DELAY TIME
RETURN
DELAY TIME
RETURN
0~99 : Adjust brightness with a manual iris lens
AUTO, 1/60, 1/100FLK, 1/120, 1/250, 1/500, 1/1000, 1/2000,
1/4000, 1/10000, 1/100000 : Adjust shutter speed
0~99 : Adjust brightness with a DC iris lens
AUTO, 1/60, 1/100FLK, 1/120, 1/250, 1/500, 1/1000, 1/2000,
1/4000, 1/10000, 1/100000 : Adjust shutter speed
Determines that use the AGC function or not and AGC
level selectable(You can not use the Auto D&N change
mode when AGC is off)
Using sense up when it is low luminance (x2~x1024)
OFF, LOW, MID, HIGH : Use BLC function or not / level
selectable
0~15: Adjust top position of BLC zone
1~16 : Adjust bottom position of BLC zone
0~15: Adjust left position of BLC zone
1~16 : Adjust right position of BLC zone
OFF : Deactivates HBLC function
HBLC LEVEL : OFF, LOW, MID, HIGH
TOP : 0~15
BOTTOM : 1~16
LEFT : 0~15
RIGHT : 1~16
ALL DAY : Activates HBLC function all day
NIGHT : Use the function at night only
1~100 : Level adjust
TOP : 0~33
BOTTOM : 1~34
LEFT : 0~44
RIGHT : 1~45
OFF : HLC MASK OFF
0~20 : DWDR level adjust
Reduce noise in low illumination(Level selectable)
Move back to previous menu
Color temperature 2500~9500
0~128 : Adjust the Red value to shift the color of the object
0~128 : Adjust the Blue value to shift the color of the object
Move back to previous menu
Find the optimal white balance for current luminance
environment
Adjust Red tone of the image
Adjust Blue tone of the image
Move back to previous menu
7~30
6~29
0~15 : Select the duration time
Move back to previous menu
6~36
6~36
0~255
0~255
0~15 : Select the duration time
Move back to previous menu
Fixed at color
Fixed at B/W
0~15 : Change the color↔B/W by external signal(N/A)
Move back to previous menu
Transmit the burst signal or not in B/W mode
Color suppress controllable
Iris suppress controllable
N/A for W/O LED version
Move back to previous menu
MANUAL
ON
OFF, LOW, MIDDLE, HIGH
AUTO, OFF, X2, X4, X8, X16, X32, X64,X128, X256, X512, X1024
OFF, LOW, MID, HIGH, AUTO
2. WHITE BALANCE
Function
setting menu Select menu ContentsSub menu
Make a zone for HBLC
Make a zone for HLC mask
3B25272A
OSD MENU
Select brightnessof illumination about changing
the day↔night mode by AGC
Select brightnessof illumination about changing
the day↔night mode by CDS
Select brightnessof illumination about changing
the day↔night mode by AGC