Huviron SK-ht21ai User manual

FULL HD-TVI(1080P)
IR WATER PROOF CAMERA
SK-P461(D)/HT21AI
MANUAL
If the product is to be put out of operation definitively,
take it to a local recycling plant for a disposal which
is not harmful to the environment.
1. Please study the instruction manual before your applications and
keep it for your future reference.
2. Do not flash LED light directly on the eyes when LEDs are on.
3. Do not install the camera on a unstable surface. It will cause falling
or other hazards.
4. Do not use improper power, it could cause fire or electric shock.
(Use the AC adaptor 12V DC regulated, 1.5A)
5. Do not disassemble or re-model the camera, it could cause fire,
electric shock or other hazards.
6. Stop using the camera when you find a malfunction like smoke or
unusual heat, it could cause fire or electric shock.
7. Due to the possibility of water leakage, do not cut or peel off the
cable. In case you cut or peel off the cable, the warranty will be
void.
8. Do not adhere dangerous articles to the camera.
9. Please use the camera unit within given temperature and electricity
limit.
10. Please make sure that installation should be done by qualified
service person only.
11. Do not disassemble the unit by yourself. When there is problem
with the unit please contact after-sale service center or the shop
where you bought.
1. 1/2.9" SONY CMOS
2. Full HD(1920x1080) Resolution
3. DAY & NIGHT Function
4. WDR (Wide Dynamic Range) Function
5. 3D DNR Function
6. Privacy mask function 16 area
7. On Screen Display menu
8. Intelligent motion detection
9. Output : HD-TVI/CVBS
10. Protocol : PELCO - C
CAUTION
ACCESSORIES
HOW TO INSTALL
DIMENSION
FEATURE
11. This camera is incredibly flexible to install with its 3-axis camera
construction, which makes the camera ceiling, wall or slope mountable
12. This product is "waterproof" to resist rain, snow and other weather
factors(IP68)
13. 30M range visible in total darkness with 40pcs of IR LEDs.(Indoor)
14. Up to 500M Full HD-TVI Tranmission via Coaxial cable.(Maximum
tranmission distance may vary with type of coaxial cable)
1. Make a hole of Ø25mm in diameter for passing cable.
2. Drill four holes on the wall or ceiling and insert the anchors.
3. Arrange the cables and fix the screws.
ANCHOR 6x30, 4EA
SCREW 4x35 TP1 PAN SUS, 4EA
WRENCH 3mm L TYPE, 1EA
SUNVISOR BOLT, 1EA
Extra video output cable for installation,
1EA(option)
5-A. Loosen the bolt A, B, C-1 and C-2 by using the 3mm wrench
included.
6-A. Face the direction of the camera to monitor.
7-A. Tighen the bolt A, B, C-1, C-2 to complete adjustment.
TYPE-A
TYPE-B
TYPE-A
TYPE-B
61.5
61.5
Ø6 Ø25
ANCHOR 6x30, 4EA
SCREW Tp1 4x35, 4EA
BOLT
SUNVISOR
* Warning : This c ap must sc rew tightly.
5-B. Loosen the bolt by using the 3mm wrench included.
6-B. Face the direction of the camera to monitor.
7-B. Tighten the bolt to complete adjustment.
WRENCH
BOLT A
BOLT C-2
BOLT C-1
BOLT B
WRENCH
BOLT
101.7
101.7
206.7
205.9
80.7
80.7
80.4
80.4

2. OSD menu structure
1. How to use the jog lever
※All specification is subject to change without notice to improve the quality. 3B26627A
STRUCTURE SPECIFICATION
MECHANICAL
Dimension 86.4(W) 101.9(H)×131.3(D) mm
Weight Approx. 900g
ENVIRONMENTAL
Ingress Protection IP68
Operating Temp -45°C ~ 50°C
Humidity 0% to 90%
FUNCTION
Protocol PELCO-C
ELECTRONICAL
Supplied Voltage DC12V±10% or AC24V±10% Dual Voltage
Current Consumption Max.650mA(at 12V DC)
LED IR LED40 PCS
CERTIFICATION
CE, FCC, ROHS Yes
CAMERA / STRUCTURE SPECIFICATION
FUNCTION SETTING
SK-P461(D)/HT21AI
VIDEO
Image Sensor 1/2.9" SONY CMOS
Total Pixels 2010(H) 1108(V) = 2,227,080 (pixel)
Active Pixels 1944(H) 1092(V) = 2,122,848 (pixel)
Scanning System Progressive Scan
Resolution
Digital : 1920X1080p (1080p, 30/25fps)
1280X720p (720p, 60/50fps)
Analog : 700TVL
S/N More than 50dB (AGC OFF)
Video Output HD-TVI
Analog : NTSC, PAL(without WDR)
Min.Illumination Color: 1.0Lux, BW: 0.5Lux
Color DSS: 0.002Lux, BW DSS : 0.001Lux
LENS TYPE
Lens Type DC Auto Iris
Focal Length f = 2.8(W) ~ 12.0(T)mm
OPERATIONAL
On screen display Yes
Day & Night TDN (Auto / Day / Night)
Brightness 0 ~ 20 steps
Shutter Speed Auto / Manual (1/30(1/25) ~ 1/60000)
Sens-up OFF / ×2~×8
AGC 0~20 steps
Backlight WDR / BLC / OFF
HLC ON / OFF
D-WDR ON / OFF
White Balance Auto / Autoext / Manual
Sharpness 0~10 steps
Digital Noise Reduction (3D) High/Middle/Low/Off
Digital Zoom ON/OFF(X1~X8)
Motion Detection ON / OFF
Privacy Masking ON / OFF (16 Zone Selectable)
Mirror H / V / H&V / OFF
Defog ON / OFF
①ENTER :
• Push the lever : Used to access the menu and confirm
selection.
• Push the lever for one second : Used to return to
previous menu from the motion detection setting section
or privacy mask setting section.
②UP, ③DOWN : Used to move the cursor to up or down.
④ LEFT, ⑤RIGHT : Used to move the cursor to left or right
and change the value.
⑥ FOCUS, ⑦ZOOM : Use a '+' type driver for adjusting
zoom and focus. (In case of operation Focus/Zoom, don't
put stress excessively.)
⑧ EXT. VIDEO : Extra video output terminal for installation.
Plug your test monitor in here. The cable is option.
* OSD menu & Focus/Zoom adjustment direction
1. Unfasten the screw of the bottom door / 2. Adjust the jog lever & Focus /Zoom trimmers
3. Tighten the screw of the bottom door
F
EXT.VIDEO
Z
7
6
8
2
5
1
3
4
3. How to control through Pelco-C communication
1) Match the camera with controller's ID, baudrate and protocol
2) Up, Down, Left and right is same as Up, Down, Left and right of
Pelco-C control
3) Enter same as menu key or IRIS open key control
Function
setting menu Sub menu Summary
1.
EXPOSURE
BRIGHTNESS Adjust brightness level 0(dark) ~ 20(bright)
LENS-DC Select when use of DC Auto-Iris lense/except
the special cases, DC is standard Model
AE MODE Select AE MODE
SHUTTER Can be set in AUTO or MANUAL
SENS-UP Select maximum DSS(Digital Slow Shutter) OFF, x2~X8
AGC Select Auto Gain Control
2.
WHITE BAL
AWB Select WHITE BALANCE mode
▷AUTO Automatically adjusts color according to the lighting
▷AUTO ext Faster extension version of Auto
MANUAL Adjust the white balance manually
3.
BACK
LIGHT
BACKLIGH Select Backlight compenstaion mode
WDR Adjust WDR level - Low / Middle / High
HLC Select High Light Compensation.
BLC
▷AREA Control BLC area according to light condition.
▷POS-X Adjust the window X- Axis position
▷POS-Y Adjust the window Y- Axis position
▷SIZ-X Adjust the window X- Axis size
▷SIZ-Y Adjust the window Y- Axis size
4.
DAY&
NIGHT
DAY&NIGHT Select Day&Night mode
AUTO-CDS
Automatic switching between day operation
(colormode) and night operation
(black and white mode)
▷IR-LED LED On/Off Control
▷ANTI-SAT Compensate when IR hunting happens.
When you use this function.
▷AGC THRS Day&Night change level. Higher level make the night
mode changed in lower illumination.
▷AGC
MARGIN Day to night and night to day switch margin
▷DELAY 2 ~ 60 second
5.
IMAGE
DNR Select Digital Noise Reduction
SHARPNESS Adjust sharpness level
COLOR GAIN Adjust Color gain value 0~20 Steps.
GAMMA Selecte gamma mode. 0.45~0.65
D-WDR Select Digital WDR(Wide Dynamic Range)
DEFOG Carry out defog function.
SHADING Select Lens shading compensation. (OFF / ON)
MIRROR
H-Flip : Flip the picture horizontally on the screen
V-Flip: Flip the picture vertically on the screen
Rotate : Flip the picture horizontally
& vertically on the screen
6.
SPECIAL
TITLE Camera title edit and display on / off select
PRIVACY Hide an area you want to hide on the screen
MOTION When there is movement of the subject on the
screen,there will be motion detection
D-ZOOM Select digital zoom magnification. Max 8x
Function
setting menu Sub menu Summary
6.
SPECIAL
LANGUAGE Select Language
COMM. Setup Camera ID and baud-rate.
(Pelco-D/P Auto detect)
7.
SYSTEM
IMAGE
RANGE Select pedestal level scale
HD Format Select HD output format. 1080p
HD FPS Select HD output frame rate.
1080p 30, 25
CVBS Select CVBS output mode. NTSC or PAL
8. RESET All the settings will be restored to the factory default
9. EXIT Escape the menu