Hybrid+ ALTIUM 15 User manual

ALTIUM 15/12
2000W, SELF-POWERED
FULL RANGE SPEAKER
REV Z0 22-02-2022

USER MANUAL - ALTIUM15 /12, 2000W SELF-POWERED FULL RANGE SPEAKER
PAGE 3PAGE 2
SYMBOL ALERTING THE OPERATOR TO FOLLOW IMPORTANT OPERATING
INSTRUCTIONS AND PRECAUTIONS DETAILED IN THIS DOCUMENT.
Do not spill water or other liquids into or on the speaker, or operate the speaker whilst
under wet or damp conditions.
Do not remove the aluminium panel of the speaker. Removing this panel will expose you
to potentially dangerous voltages. There are no user-serviceable parts inside.
Do not use the speaker if the electrical power cable is frayed or damaged. The power
supply cable should be routed so that it is not walked upon or pinched by objects close by.
Only use the original power cable supplied with your speaker.
Do not connect the input or output connectors of your speaker to any other voltage
sources such as batteries, mains power or power supply units, regardless of whether the
Speaker is switched on or off.
During long periods of no use, the power cable should be unplugged from the mains
voltage outlet.
Precaution should be taken so that the earth connection is not defeated.
Never use your speaker near heat radiating appliances such as stoves
and heaters.
Ensure that power outlets and mains voltage conform to the power requirements printed
on the back panel of the speaker.
Do not apply an input signal that is much greater than that which is required to achieve
maximum output level. This may damage the pre-amplification stage circuitry.
Always operate the speaker with the AC earth wire connected on both sides
(Speaker and Mains).
Ensure that power outlets and mains voltage conform to the power requirements printed
on the back panel of the speaker.
Do not operate your speaker on a surface or environment which may impede the normal
flow of air around the speaker.
SYMBOL WARNING THE OPERATOR THAT UNINSULATED, DANGEROUS VOLTAGES
ARE PRESENT WITHIN THE ENCLOSURE THAT MAY POSE A RISK OF ELECTRIC
SHOCK.
- The power supply cord or plug/s have been damaged.
- Liquids have been spilled inside the speaker enclosure.
- The speaker has been exposed to rain or excessive moisture.
- The speaker does not appear to operate normally, or exhibits a reduction in performance.
- The speaker has been dropped or the enclosure is damaged.
Save the carton and packing material even if the speaker has arrived in perfect condition.
Should you ever need to ship the speaker for servicing, use the original packaging supplied.
After long periods of no use, the power cable should be inspected for any damage before
using the speaker again.
Read all documentation before operating your speaker. Retain all documentation for future
reference.
Your speaker should be serviced only by qualified service personnel. Contact your nearest
official retailer should your speaker need technical attention.
If the speaker is used in an extremely dusty or smoky environment, the amplifier should
periodically be blown free of foreign matter.
Follow all instructions printed on this user manual and the back panel of the speaker for
proper and safe operation.
Your speaker should be serviced by a qualified service technician when:
PAGE 3PAGE 2
IMPORTANT PRECAUTIONS

USER MANUAL - ALTIUM15 /12, 2000W SELF-POWERED FULL RANGE SPEAKER
PAGE 5PAGE 4
INTRODUCTION
UNPACKING
INSTALLATION AND MOUNTING
Congratulations on your purchase of the new Hybrid+ Altium15/Altium12 powered speaker,
and thank you for your confidence in the Hybrid+ brand. You are amongst the growing number
of audio professionals who have made Hybrid+ one of Southern Africa’s leading brands of
professional and commercial audio systems.
Please inspect the speaker carefully immediately after unpacking. If you find any visible
damage, notify your supplier/retailer immediately. Be sure to save the carton and all packing
materials should you need to ship the unit back to your authorised service centre.
Both Hybrid+ Altium15/Altium12 speakers can be used as free standing, pole mounted or
hung/suspended.
A Top-Hat has been fitted underneath the speaker for pole mounting, with dual angle
operation (0 and 10°)..
7 x M8 flypoints have been included for fixed suspended installations. Three of the flypoints
are located on the top of the speaker, another three on the bottom and the last one on the
rear of the cabinet for angling purposes.
Hybrid+ Altium15/Altium12 offers an 18 month “No-Quibble” carry-in guarantee, and should
your speaker, in the unlikely event, be damaged upon receipt and inspection, we offer
an exchange immediately, provided that all packaging and cabling is returned in original
condition.
For your safety, please read the important precautions before installing and operating your
speaker. The Hybrid+ Altium15/Altium12 is based on the same advanced circuit topologies
that have made Hybrid products the choice of professionals for the past 30 years. The
Hybrid+ Altium15/Altium12 has been designed for high operating efficiency and accurate
sonic performance across the full audio bandwidth, even under stressful conditions.
Internal components are the finest available, and sub-assemblies are pre-tested before final
assembly. Finally, each speaker is “burned in” and thoroughly tested using precision audio
test equipment before shipping. In addition, both the Hybrid+ Altium15/Altium12 incorporates
extensive protection features to safeguard both internal circuitry and transducers. This
proven combination of advanced design, quality construction and comprehensive circuit
protection is your guarantee of fail-safe reliability, and you can depend on consistent, stable
performance.
Self-Powered Professional Speaker
INPUT
LIMIT
LINK EDIT
ENTER
POWER
INPUT OUTPUT
1200W
220-240 Vac 50-60Hz
MAX POWER
FUSE: 6.3A
CONSUMPTION
PURE
SOUND
CLASS D
AMP
OPTO
LIMITER
PFC
SMPS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:TO REDUCETHE RISK OF FIRE
OR ELECTORIC SHOCK. DO NOT EXPOSETHIS
REMOVECOVER. NO USER SERVICEABLE
EQUIPMENTTORAIN OR MOISTURE. DO NOT
QUALIFIED PERSONNEL.
PARTINSIDE. REFER SERVICINGTO
AVIS: RISQUE DE CHOC ELECTRIC NEPAS OUVRIR!
1 2 3
4
9
5 6 8
7
Self-Powered Professional Speaker
INPUT
LIMIT
LINK EDIT
ENTER
POWER
INPUT OUTPUT
1200W
220-240 Vac 50-60Hz
MAX POWER
FUSE: 6.3A
CONSUMPTION
PURE
SOUND
CLASS D
AMP
OPTO
LIMITER
PFC
SMPS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:TO REDUCETHE RISK OF FIRE
OR ELECTORIC SHOCK. DO NOT EXPOSETHIS
REMOVECOVER. NO USER SERVICEABLE
EQUIPMENTTORAIN OR MOISTURE. DO NOT
QUALIFIED PERSONNEL.
PARTINSIDE. REFER SERVICINGTO
AVIS: RISQUE DE CHOC ELECTRIC NEPAS OUVRIR!
1 2 3
4
9
5 6 8
7
1: Power on-off switch 4: Fuse holder 7: LCD screen
2: Powercon IN connector 5: Input connector 8: Rotary encoder
3: Powercon OUT connector 6: Input loop through 9: Limit LED
PAGE 5PAGE 4
USER INTERFACE ELEMENTS
Rear Panel

USER MANUAL - ALTIUM15 /12, 2000W SELF-POWERED FULL RANGE SPEAKER
PAGE 7PAGE 6
2: POWERCON IN CONNECTOR
5: INPUT CONNECTOR
1: POWERCON IN CONNECTOR
6: INPUT LOOP THROUGH
PIN-OUT CONFIGURATION AS A MONO BALANCED INPUT
PIN-OUT CONFIGURATION AS A STEREO UNBALANCED INPUT
4: FUSE HOLDER
3: POWERCON OUT CONNECTOR
Main power switch, switching the speaker ON or OFF. Once the speaker is switched ON, the
LCD screen will illuminate.
Mains 220 - 240Vac Input connector.
Speaker Input.
Speaker Input.
Pin 1 – Ground
Pin 1 – Ground
Pin 1 – Ground
Pin 3 – Inverting (Cold)
Pin 3 – Left Input
Pin 3 – Inverting (Cold)
Pin 2 – Non-Inverting (Hot)
Pin 2 – Right Input
Pin 2 – Non-Inverting (Hot)
It is recommended that should the fuse be blown, take the speaker for testing to your
nearest authorised service centre. Usually when a fuse has blown, it indicates that there are
damaged components within the circuitry of the speaker. By changing the fuse and restarting
the speaker, it may cause further damage to components.
DO NOT modify the cable in any way.
Do not load (Daisy Chain) more than 3 cabinets from the same mains outlet. Overloading the
power source may cause the line circuit breaker to activate and in extreme cases could be a
fire hazard.
Only use the cable supplied with this speaker to power up the unit (Powercon – 3 Pin Mains
South African plug).
The XLR input female connector can be configured as a mono balanced input or a stereo
unbalanced input. To select between the two input modes, the balanced / Unbalanced switch
must be activated within the software via the encoder or app.
The XLR Input Female connector can be configured as a Mono Balanced input or a Stereo
Unbalanced input. To select between the two input modes, the Balanced / Unbalanced switch
must be activated within the software via the encoder or app.
Mains 220 - 240Vac loop through Output connector, allowing multiple Hybrid+ Altium15/
Altium12 speakers to be powered by the same mains outlet.
Inspect the cable before use and should any sign of damage be visible, replace the cable with
the exact same, available from your nearest authorised retailer.
Only use Powercon Output – Powercon Input cables to connect multiple speaker cabinets.
3 Core cable (Live, Neutral and Earth), min. 1mm diameter / core.
DO NOT attempt to bypass the fuse in any manner by bridging the fuse with solid
conductor.
DO NOT replace the fuse with an incorrect value fuse. Only replace the fuse with
the exact fuse rating as printed on the back panel.
PAGE 7PAGE 6

USER MANUAL - ALTIUM15 /12, 2000W SELF-POWERED FULL RANGE SPEAKER
PAGE 9PAGE 8
7: LCD SCREEN 9: LIMIT LED
8: ROTARY ENCODER
The LCD screen informs the operator of important information, changing page displays when
the encoder is activated (Toggle pressed).
WiFi identification, Model Number, Firmware version, and the wireless mode
(WiFi or Bluetooth).
A red LED indicates when the speaker has reached its optimum SPL performance and the
internal limiters have activated, protecting the speaker and electronics.
Preset 1 – Full Range FLAT
Preset 3 – Satellite Live
Preset 4 – Satellite Music
*Save User settings
Preset 2 – Music
The rotary encoder performs two functions. By rotating the encoder clockwise or
anticlockwise, parameters can be changed. By pressing the encoder, the parameter is
temporarily stored and the next function page appears.
TIP: Do not drive the power amplifier beyond this point as it will degrade the audio
quality which may damage your loudspeakers.
Input Channel level in dB, ranging from -80 to 0.
Mode: Mono Balanced or Stereo Unbalanced.
Mid EQ level in dB, ranging from -12 to +6
Master Channel level in dB, ranging from -33 to 0, including Output VU bar readings for both
LF and HF integrated amplifiers.
The limit LED has a second function, illuminating briefly when the Line/Mic input selection is
changed from Line to Mic or vice versa.
Bluetooth Channel level in dB, ranging from -80 to 0.
Input Selection: Line Input or Microphone Input.
Treble EQ level in dB, ranging from -12 to +6dB
Preset Seleection:
PAGE 9PAGE 8

USER MANUAL - ALTIUM15 /12, 2000W SELF-POWERED FULL RANGE SPEAKER
PAGE 11PAGE 10
USING BLUETOOTH AS THE INPUT SOURCE
Connect the Powercon mains cable provided with the Altium15/Altium12 to the mains
outlet and the speaker, and power up the unit by switching the power switch (1) ON.
Normal mode will automatically be selected without any further action, whilst WiFi mode
is selected by pressing and holding the rotary encoder (8) during the countdown from 3
to 0.
Open the Bluetooth application on your mobile device or PC/laptop and find the device
starting with HYBRID+_ followed by 6 Alphanumerics (HYBRID+_XXXXXX). Enable the
connection to this device. It will prompt you for a Password. Type in the factory default
password as follows: 1234 AND PAIR THE TWO DEVICES TOGETHER. (This password is a
factory default password for all Altium15/Altium12 cabinets and can be changed to your
own personalised code using the Utilities menu).
Mono Balanced and Stereo Unbalanced connections may be used with the following
pinout configuration:
TIP: It is recommended to always use balanced line inputs as opposed to unbalanced
inputs, ensuring a +6dB gain structure and noise reduction throughout your system.
Once the Altium15/Altium12 has been switched on, it will go through its start-up sequence,
initially displaying the “HYBRID+ LOGO” on the LCD screen and starting a countdown
from 3 to 0, prompting the user to select either “normal mode” of “WiFi mode”.
To access the bluetooth module, the Altium15/Altium12 must be in Normal Mode. The
bluetooth module is unavailable when the Altium15/Altium12 is in WiFi Mode.
Once successful connection / pairing is made, audio playback from your mobile device or
PC/laptop is possible.
It is recommended that you have the volume setting of the mobile device/PC/laptop
muted or at a low level in order to avoid abnormally high input signals that may overload
your speaker.
The XLR Female input connector (5) can be used in “Normal” mode or “DSP mode”.
INSTALLATION AND MOUNTING
Use the Input XLR (Female) connector (5) on the rear panel to supply an audio signal to
your Altium15/Altium12 powered speaker. The link XLR (Male) connector (6) may be used to
daisy-chain the audio input to other Altium15/Altium12 powered speaker cabinets when
necessary. The link XLR (Male) connector will only mirror input signals from the XLR
(Female) connector and NOT from the bluetooth input.
It is recommended that you make all input and loop through connections before powering
up your Altium15/Altium12 speaker and the input signal should be muted from your source.
This will avoid unexpected “thumps” when powering your Altium15/Altium12 speaker and
abnormally high input signals that may overload your speaker.
Once the Altium15/Altium12 has been switched on, it will go through its start-up sequence,
initially displaying the “HYBRID+ LOGO” on the LCD screen and starting a countdown from
3 to 0, prompting the user to select either “normal mode” or “WiFi mode”. Normal mode
will automatically be selected without any further action, whilst WiFi mode is selected by
pressing and holding the rotary encoder (8) during the countdown from 3 to 0.
Connect the powercon mains cable provided with the Altium15/Altium12 to the mains
outlet and the speaker, and power up the unit by switching the power switch (1) ON.
USING THE XLR CONNECTOR AS THE INPUT SOURCE
Pin 1 – Ground Pin 1 – Ground
Pin 3 – Inverting Input (-) Pin 3 – Left Input
Pin 2 – Non-Inverting Input (+) Pin 2 – Right Input
MONO BALANCED STEREO UNBALANCED
PAGE 11PAGE 10

USER MANUAL - ALTIUM15 /12, 2000W SELF-POWERED FULL RANGE SPEAKER
PAGE 13PAGE 12
USING THE ALTIUM15/ALTIUM12 IN WIFI MODEUSING THE ALTIUM15/ALTIUM12 IN WIFI MODE
To access the WiFi Mode, immediately after switch on, press the encoder and hold it down
whilst the countdown from 3 to 0 appears on the LCD screen. Once successful the LCD
screen will indicate “START WIFI” and thereafter “WiFi Mode”. You have now successfully
entered WiFi Mode
To access “Normal Mode”, switch on the Altium15/Altium12 and allow it to go through its
start-up sequence with no further action required by the user. After a few seconds the LCD
screen will enter the home page, displaying the Master level with dual bar graph displays
of the LF and HF internal amplifiers. Rotating the encoder (8) clockwise will increase the
master level in increments of 1dB. Similarly, rotating the encoder anticlockwise, will have
the adverse effect. The master level has a range of -33dB to +6dB.
Open your web browser and type in the following IP address: 192.168.4.1 After a few
seconds the software application will load and display as per the diagram below.
Presets 3 and 4 are recommended when using the Altium15/Altium12 together with a
sub-bass cabinet.
Once the “save changes” are confirmed, any changes to levels, modes, EQ settings and
presets 1 - 4 will be stored. Once the speaker is switched off and restarted, the new saved
settings will be loaded.
Open the WiFi application on your mobile device or PC/Laptop and find the network starting
with HYBRID+_ followed by 6 Alphanumerics (HYBRID+_XXXXXX). Enable connection to
this network. It will prompt you for a Password. Type in the factory default password as
follows: 12345678 (This password is a factory default password for all Altium15/Altium12
cabinets and can be changed to your own personalised code using the Utilities menu).
Pressing the encoder once will toggle the display to the next menu page. Changes are
made by rotating the encoder clockwise or anticlockwise. Pressing the encoder once
more will display the next menu page and so on. Below is the sequence of menu pages:
1) Master level (home page) -30dB to +6dB (Factory default set at +6dB)
3) Bluetooth player level -60dB to 0dB (Factory default set at 0dB)
6) LF EQ -12dB to +6dB (Factory default set at 0dB)
8) HF EQ -12dB to +6dB (Factory default set at 0dB)
2) Input level -60dB to 0dB (Factory default set at 0dB)
5) Input Selection between Line or Microphone (Factory default set to Line)
7) MF EQ -12dB to +6dB (Factory default set at 0dB)
9) Preset selection 1 - 4 (Factory default set to Preset 1)
10) Save changes
* Preset 1 - FLAT
* Preset 3 - SATELLITE LIVE
* Preset 4 - SATELLITE MUSIC
* Preset 2 - MUSIC
M ono_Ba l
Unlock Utilitie s
Inpu t
Input Level
LOWM ID HIGH
0dB
0dB0 dB 0dB
0dB6 dB
Line/Mic Select Bluetooth Level
Input EQ
Output Level
Line
1 2
3 4
5 6 7 8
9 10 11
1: Mono _Bal
2: Preset 1- Altium Flat
4: Utilities
6: Line/Mic Select
8: Output Level
10: MID
3: Unlock
5: Input Level
7: Bluetooth Level
9: LOW
11: HIGH
PAGE 13PAGE 12

USER MANUAL - ALTIUM15 /12, 2000W SELF-POWERED FULL RANGE SPEAKER
PAGE 15PAGE 14
1) Mono Balanced / Stereo Unbalanced switch (Factory default is set to Mono Balanced)
2) Preset selection scroll bar:
All functions and settings can now be edited using the sofware app, with a few added
features using the Utilities tab:
- WiFi and Bluetooth setup: Allows for WiFi and bluetooth passwords to be edited and saved.
- Write: Not available for user editing – For factory and R&D use only.
- Defaults: Once selected all original factory settings will be reloaded to your
Altium15/Altium12.
- Show: Shows the DSP workflow diagram.
- Upgrade: Allows for future software upgrade files to be loaded.
3) Unlock: Not available for the user, it is a password protected unlock tab that opens the
complete DSP function including crossover networks and limiters – For factory and R&D
use only.
4) Utilities: Once the utilities tab is selected, a scrolldown bar will appear with the following
options:
6) Line /Mic selection switch (Factory default set to Line)
9) Low: LF EQ -12dB to +6dB (Factory default set at 0dB)
5) Input level -60dB to 0dB (Factory default set at 0dB)
8) Output Level -30dB to +6dB (Factory default set at +6dB)
11) High: HF EQ -12dB to +6dB (Factory default set at +0dB)
7) Bluetooth player level -60dB to 0dB (Factory default set at 0dB)
10) Mid: MF EQ -12dB to +6dB (Factory default set at +0dB)
* Preset 1 - FLAT (Factory default)
* Preset 3 - SATELLITE LIVE
* Preset 4 - SATELLITE MUSIC
* Preset 2 - MUSIC
NOTE: BLUETOOTH IS NOT AVAILABLE IN WIFI MODE.
Ensure that the speaker does not go beyond its clipping point. This threshold is
determined by the illumination of the red CLIP LIMIT LED found on the rear panel.
Users will not need to make any internal adjustments to the speaker throughout
its lifetime. There are no user-serviceable parts inside. Removal of the module or
15” speaker exposes risk of shock, and any servicing needed should be carried
out by an authorised and qualified service centre.
USER PRECAUTIONS
Your Altium15/Altium12 Self-Powered Speaker automatically protects itself to a certain
degree from DC voltages, clipped waveforms and subsonic (20Hz<) frequencies, however,
correct usage of the Speaker should always be followed in order to ensure longevity of your
Your Altium15/Altium12 requires no routine maintenance other than the occasional
cleaning of the cabinet and the amplifier module using a dry cloth and a water-based mild
detergent or spray.
In the unlikely event that your speaker develops a problem, it should be returned to an
authorised distributor or service centre. Due to the complexity of the design and the risk
of electrical shock, all repairs must be carried out by authorised and qualified personnel.
If the speaker needs to be couriered to the distributor or service centre, ensure that it is
correctly packed in its original packaging so as to avoid further damage.
Your Altium15/Altium12 carries from date of purchase an 18 month, no quibble walk-in
guarantee. Hybrid+ prides itself for its excellent after sales service and it is our goal to
return your Speaker back to you in perfect working order.
SPEAKER PROTECTION
MAINTENANCE
SERVICE AND REPAIR
THANK YOU FOR PURCHASING A HYBRID+ PRODUCT AND FOR READING THIS USER
MANUAL. YOU ARE NOW READY TO USE YOUR ALTIUM15/ALTIUM12 AND WE HOPE IT
BRINGS YOU MANY HOURS OF LISTENING PLEASURE.
PAGE 15PAGE 14

PAGE 16 www.vivaafrika.co.za
Cabinet
Construction
Precision CNC manufacturing process
Braced 15mm Birch plywood
Pressurized Tongue and Groove assembly
Cabinet
Finish and
Accessories
4 coats of Textured Half Gloss Black Paint, Ultratex V3 (USA)
Braced 1.5mm powder coated dual tone design grille
Anti-corrosion stainless steel machine screws and nuts
2 x Metal cup handles
7 x M8 Fly-points (3 Top, 3 Bottom, 1 Back)
Dual angle fibre reinforced ABS 35mm Top-hat (0° and 10°)
15” Low
Frequency
Speaker
Model: 15MB354-4
Replacement recone: 15MB354-4RK
Power rating: 1400W Peak, 700W Program, 350W rms
Impedance: 4Ω
Aluminium diecast frame
Voice Coil: 2.5” (63mm) IN-OUT Copper (350° Celsius EIC
grade)
Magnet: Ferrite (170 x 20mm)
Ribbed fibre-loaded paper cone with triple roll surround
1” High
Frequency
Driver
Model: PCD440B
Replacement Diaphragm: PCD440B DK
Power rating: 200W Peak, 100W Program, 50W rms
Exit: 1” (25mm)
Impedance: 8Ω
Diaphragm: Space grade Ketone Polymer (UK)
Voice Coil: 1.7” (44mm) Flat aluminium wire (Japan)
Magnet: Ferrite (115mm)
Electronic
X-Over
1.8KHz, 24dB/Octave, phase corrected
SMPSU 90% Efficiency
Metal Shield enclosed
Low no-load consumption <0.5W
Short circuit protection
Overload protection
Over voltage protection
Thermal protection
Class D Audio
Amplifier
Dual channel power amplifier (LF and HF)
Rated power: 2 x 1260W Peak, 2 x 630W Program, 2 x 315W
rms @4Ω
THD+N: 0.006%/1W
SNR: 112dB
Dynamic range: 113dB
DSP 1 IN - 2 OUT
4 user selectable presets
Preamp DSP resolution: 56bits
Converters: 24bits/48KHz with 104SNR
Crossover slopes: Linkswitz-Riley, Butterworth & Bessel
EQ: 19 x Full parametric EQ
EQ Types: PEQ, Low and High Shelve, Notch, Low and
High Pass
Time Alignment: 17ms/Output
Dual protection compressor-limiters
Phase correction
Balanced Mic/Line Inputs
Bluetooth 5.0 Audio Player
32 bit MCU Control
WiFi DSP control - No app installation needed
Gross
dimensions
440 x 710 x 450mm (W/H/D) ; Mass: 24kg
Net
dimensions
410 x 660 x 420mm (W/H/D) ; Mass: 21kg
Cabinet
Construction
Precision CNC manufacturing process
Braced 15mm Birch plywood
Pressurized Tongue and Groove assembly
Cabinet
Finish and
Accessories
4 coats of Textured Half Gloss Black Paint, Ultratex V3 (USA)
Braced 1.5mm powder coated dual tone design grille
Anti-corrosion stainless steel machine screws and nuts
2 x Metal cup handles
7 x M8 Fly-points (3 Top, 3 Bottom, 1 Back)
Dual angle fibre reinforced ABS 35mm Top-hat (0° and 10°)
15” Low
Frequency
Speaker
Model: 12MB354-4
Replacement recone: 12MB354-4RK
Power rating: 1400W Peak, 700W Program, 350W rms
Impedance: 4Ω
Aluminium diecast frame
Voice Coil: 2.5” (63mm) IN-OUT Copper (350° Celsius EIC
grade)
Magnet: Ferrite (170 x 20mm)
Ribbed fibre-loaded paper cone with triple roll surround
1” High
Frequency
Driver
Model: PCD440B
Replacement Diaphragm: PCD440B DK
Power rating: 200W Peak, 100W Program, 50W rms
Exit: 1” (25mm)
Impedance: 8Ω
Diaphragm: Space grade Ketone Polymer (UK)
Voice Coil: 1.7” (44mm) Flat aluminium wire (Japan)
Magnet: Ferrite (115mm)
Electronic
X-Over
1.8KHz, 24dB/Octave, phase corrected
SMPSU 90% Efficiency
Metal Shield enclosed
Low no-load consumption <0.5W
Short circuit protection
Overload protection
Over voltage protection
Thermal protection
Class D Audio
Amplifier
Dual channel power amplifier (LF and HF)
Rated power: 2 x 1260W Peak, 2 x 630W Program, 2 x 315W
rms @4Ω
THD+N: 0.006%/1W
SNR: 112dB
Dynamic range: 113dB
DSP 1 IN - 2 OUT
4 user selectable presets
Preamp DSP resolution: 56bits
Converters: 24bits/48KHz with 104SNR
Crossover slopes: Linkswitz-Riley, Butterworth & Bessel
EQ: 19 x Full parametric EQ
EQ Types: PEQ, Low and High Shelve, Notch, Low and
High Pass
Time Alignment: 17ms/Output
Dual protection compressor-limiters
Phase correction
Balanced Mic/Line Inputs
Bluetooth 5.0 Audio Player
32 bit MCU Control
WiFi DSP control - No app installation needed
Gross
dimensions
370 x 630 x 390mm (W/H/D) ; Mass: 20kg
Net
dimensions
340 x 595 x 345mm (W/H/D) ; Mass: 17.8kg
SPECIFICATIONS
PAGE 16