Hyperikon Triple Motion User manual
(888) 846-4973
9393 Waples St, Suite 120,
San Diego, CA 92121
info@hyperikon.com
www.hyperikon.com
Triple Motion Security Light
INSTALLATION INSTRUCTIONS
GENERAL: All electrical connections must be in accordance with
local and National Electrical Code (N.E.C.) standards. If you are
unfamiliar with proper electrical wiring connections obtain the
services of a qualified electrician.
TURN OFF POWER FROM THE MAIN CIRCUIT BEFORE
INSTALLING FIXTURE. Make sure fixture is grounded per National
Electrical Codes (NEC).
The safeguards and Instructions appearing on this page are not
meant to cover all possible conditions and situations that may
occur. It may be understood that common sense, cautions and
care, are factors which cannot be built into any product. The
person(s) installing, operating and responsible for the light fixture
must execute these factors.
WARNING Risk of fire and electrical shock. Most dwellings built
before 1985 have supply wires rated 60 degrees C. Consult a
qualified electrician before installing. If supply wires are located
within 3 inches of the ballast, use wires rated at least 90°C.
WARINING - To help prevent the possibility of electrical shock, the
use of rubber sole shoes is recommended. Exercise care; use work
gloves when handling the fixture to avoid cuts or abrasions.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE
APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH
THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND
THE HAZARDS INVOLVED.
INSTALLATION INSTRUCTIONS
1. Tools needed: Philip’s and Flathead screwdriver, adjustable
wrench, wire nuts, electrical tape, silicone calk.
2. Exercise care when handling the fixture to avoid cuts or
abrasions, to help prevent the possibility of electrical shock,
it is recommended to use rubber sole shoes.
3. Carefully unpack and check contents of the box to be sure
everything is included.
4. Turn OFF Power at circuit breaker box.
5. Install Cross Bar (10) to junction box using two 3/4” screws (11)
6. Electrical Connections: Make sure the supply wires and ground
wire of fixture go through the Gasket (15). Attach green/ or bare
copper wire and the green ground wire of fixture (6) to the crossbar
(10) using the ground nut of the crossbar. (Ground wire must be
properly attached or unit may not work). Connect the white supply
wire to the white fixture wire (8), cover them with a wire nut (7) or
twist together and cover really well with electrical tape. Connect
the black supply wire to the black fixture wire (9), cover them with a
wire nut (7) or twist together and cover really well with electrical
tape. Push the connected wires back into the electrical box.
7. Install Bracket Screw (1) into center hole of Fixture Back Mount
base (5). Align Fixture over J-box with Gasket (15) between it and
the Canopy. Secure the Unit to Cross Bar by tightening Center
Bracket Screw (1). Loosen adjustment knobs (13) and aim lamp
heads (14).
8. Turn on electricity at fuse or circuit breaker box and Test Unit
success of installation. (see motion)
9. Place a small streak of silicone caulk on the edge of the fixture
bracket, except at the brackets lower edge. Place the bracket of the
fixture so the bracket connecting screw protrudes out of the hole on
the fixture bracket. Make sure the fixture is oriented right side up
and not upside down on the mounting surface. Confirm that the
caulking sealant is completely around the edge of the fixture brack-
et where it meets the walls surface (There should be no caulking at
the lower edge of the bracket). Use the bracket securing nut with
rubber washer (3) to tighten up the bracket to the wall. If the fixture
bracket is not tight against the wall, you may need to adjust the two
nuts that are on the bracket connecting screw. Make sure the unit
is tight and secure against the wall.
Outlet box (12)
Crossbar
Screws (11) White Wire Supply (8) Mount Base (5)
Center Screw (4)
Bracket Screw (1)
Screw Ring (2)
Rubber Washer (3)
Green or Bare
Ground Wire (6)
Wire Nut (7)
Black Wire
Supply (9)
Gasket (15)
Cross Bar (10)
PLEASE READ CAREFULLY AND SAVE THESE INSTRUCTIONS, AS YOU MAY NEED THEM AT A LATER DATE.
RISK OF FIRE AND ELECTRIC SHOCK.
CONSULT A QUALIFIED ELECTRICIAN BEFORE
INSTALLING.
WARNING
(888) 846-4973
9393 Waples St, Suite 120,
San Diego, CA 92121
info@hyperikon.com
www.hyperikon.com
Triple Motion Security Light
INSTALLATION INSTRUCTIONS
1. MOUNTING BRACKET 3. INSTALL LAMP BODY
2. CONNECT WIRE AND LAMP BODY
4. BLOCKING LAMP BODY AND
MAKE IT WATERPROOF
AFTER INSTALLING YOUR MOTION ACTIVATED LIGHT, YOU ARE READY TO SET/AIM THE MOTION SENSOR. MAKE SURE THE WALL
SWITHCH IS IN THE ON POSITION.
1) Switch the TIMES/TEST switch in the TEST position to disable the photocell and allow light to come on during daylight hours.
2) Rotate the RANGE knob fully clockwise to maximum RANGE.
3) Aim the MOTION SENSOR HEAD level at least 10 Degrees downward an across the traffic pattern you want to detect.
4) Test Motion detection zone by walking across the pattern in the targeted coverage area. A red LED indicator light in the motion head will
flash when motion is detected and the lights will come on for approximately (40 seconds). Move to a different spot in the area to be tested
and stop all motion for about 8 seconds. The lights should turn off. Start walking again to see if your motion is detected in the new spot. Move
further away to check the distance and adjust range to your desired location.
5) SET ON TIME: When you are satisfied with the area of coverage, rotate the TIME/TEST switch to the opposite end to take the motion
sensor out of the TEST mode. Now you can rotate the switch to set the ON time. The TIME setting switch will let you adjust the time that the
light will stay on after motion is detected from approximately 1 to 10 minutes.
6) MANUAL OVERRRIDE METHOR: To disable the motion and keep the light continuously on in the darkness, flip the wall switch off and back
on within 3 seconds. If you leave the light on all night, it will automatically turn off at dawn and reset to Security Mode.
SET/AIM THE MOTION SENSOR
PLEASE READ CAREFULLY AND SAVE THESE INSTRUCTIONS, AS YOU MAY NEED THEM AT A LATER DATE.
Table of contents
