HYPERVOLT Home 3.0 User manual

!
Hypervolt Home 3.0 Quick Start Guide Draft V1.0
IMPORTANT - PLEASE READ
This is a basic guide, it must not be used as a substitute for the full manual (Scan the QR
Code on the back) which must be consulted before installation. Hypervolt installations
must only be done by qualified, registered electricians. All installation work for safety &
preservation of warranty must be compliant with BS7671 as amended.
Quick Start Guide
Home 3.0

!
Hypervolt Home 3.0 Quick Start Guide Draft V1.0
Charger Layout
INSTALLATION
1
2
3
9
4
5
6
7
8
10
11
12
10A

!
Hypervolt Home 3.0 Quick Start Guide Draft V1.0
Key Components
INSTALLATION
Incoming Supply Connections - LIVE, NEUTRAL & CPC (Earth) We
recommended using stranded cables with ferrules. Tighten to 2.3 Nm.
1
2
Tethered Cable Connections - This is where the tethered car charging
cable is connected. If you replace this cable remember to put the Blue &
Brown wires back through part 8.
3
CP Connection - This is where the control pilot from the car charging
cable is connected. It goes in the right side, push the tab to insert.
4
CT Connection - The CT clamp supplied should be connected here,
extend the cable as necessary using HyperConnect or CAT cable. Use
the Left plug for ALM, The Right Plug is for Additional monitoring (see
main manual).
5
RJ45 Connection - For a hardwired internet connection plug in here. You
only need to use the Orange & Green pairs of a CAT cable in the standard
T-568B configuration.
6
ALM Adjustment Dial - For setting the Automatic Load Management.
(See page 4)
7
Derating DIP Switches - For hard setting the Maximum charging limit
(See page 4). Soft set in the App.
8
Sensing Device (RCD-DD) - Internal 6mA DC sensor. You must fit an
external AC Sensing “A” Type RCD or RCBO (40A Recommended).
9
LED Front Plate Connection - This is where the LED lights plug in
10
Cut for Rear Entry Gland - Drill out if required, 25mm Max Ø, seal
accordingly. Original entry hole must be sealed if this one is used.
11
Main Brain - Where all the HyperMagic happens.
12
HyperConnect Cable - Live, Neutral & CPC + CAT 5
10A
Additional Cable Entry - Drill out for Band 1 Cables, 20mm Max Ø,

!
Hypervolt Home 3.0 Quick Start Guide Draft V1.0
INSTALLATION
Connection to an Electrical Supply (230v)
Below is the most commonly used & recommended method of
connecting your Hypervolt to an electrical supply.
Connect the charger
The CT clamp must be
installed to measure the total
supply load with the arrow
pointing in the direction of
current flow.
4 & 6mm Non & SWA
Live, Neutral, CPC & Cat 5e
HyperConnect
We recommend using HyperConnect cable for installing Hypervolt EV
Chargers, it contains power, data and CT connection wires in one neat easy
to fit cable. Available direct from Hypervolt.
CT Plug
The White Wire from the CT goes in the Left &
Black in the right. Extend as necessary, a Brown
pair of a CAT cable is used in this example.
RJ45 Plug (T-568B)
6
3
2
1

!
Hypervolt Home 3.0 Quick Start Guide Draft V1.0
Adjust the ALM (Automated load management)
The ALM is used to provide protection to the incoming supply by
preventing charging above 6A at an upper limit set by dial ( ).
Note: The dial is small so double check you have set it correctly, The arrow in the
picture below shows where the dial is pointing, 5 in this case.
Hard setting the current limit
The hard current limit sets the maximum current the Hypervolt will
charge a vehicle at. Set the dip switches ( ) accordingly.
Note: The current limit can be soft set in the App, a hard set overrides a soft set.
6: 60A
7: 80A
8: 100A
Setting ALM and Current
INSTALLATION
10A
1 2 3 4
ON
16A
1 2 3 4
ON
20A
1 2 3 4
ON
32A
1 2 3 4
ON

!
Hypervolt Home 3.0 Quick Start Guide Draft V1.0
Connecting Online
USING THE CHARGER
To adopt your Hypervolt charger to an App account and get it online,
first download the Hypervolt App (QR Code on back page) then follow
these 4 steps;
Sign Up / Sign In To start you will need to create a Hypervolt user
account via the ‘Sign Up’ tab and then use the ‘Sign In’ tab to login.
1
Adopt Next you need to ‘adopt’ your charger by choosing an ‘Available’
Hypervolt on the ‘Select your charger’ page.
2
Connect to your Wi-Fi Next select your Wi-Fi connection and enter
the the password.
3
Success ! Once your Hypervolt has connected the pulsing white ring
around the edge of the cover will turn solid blue. You can now use the
App with all its great features.
(Hypervolt Trusted Installers have access to an Installers App for the above process)
4

!
Hypervolt Home 3.0 Quick Start Guide Draft V1.0
LED Statuses
USING THE CHARGER
The LED coloured light statuses show what action your charger is
performing.
Note: These states are overridden by an LED Mode (e.g. Party Mode)
*If your Hypervolt is continually displaying a red fault status please contact our support team.
Not Online
(Pulsing White Ring
with Solid Blue Bolt)
Standby
Plug & Charge
Paused (Pulsing)
Stopped (Flashing)
Charging
Delayed Start
Standby
Schedule Charge
Waiting to
Schedule Charge
Waiting for Solar
(Super Eco Mode)
Lock
Unauthorised Use
(Flashing)
*Fault

Hypervolt Home 3.0 Quick Start Guide Draft V1.0
Go to hypervolt.co.uk/support for lots of additional support materials.
Your installer must register the installation to start the Hypervolt
warranty.
Need more support ?
CONTACT US
0333 090 3093
[e-mail].u
Your Hypervolt
Installers please pass this
guide to the end user to
keep for their records
Want to Control your
charger with the app,
Scan Me
Scan Me to Register
Your Hypervolt and
Claim Your Warranty
Scan Me to Download
the Full Manual
Hypervolt Home 3.0 Quickstart guide Version 1.1
Please note this Quick Start guide is subject to change. For the latest information please refer to www.hypervolt.co.uk/support.