i3-TECHNOLOGIES i3SIXTY F43-C User manual

i3-TECHNOLOGIES
i3SIXTY Mobile Stand
F43-C
INSTALLATION MANUAL
20190724

IMPORTANT SAFETY WARNINGS
1. When noticing damage to the power cable, immediately disconnect the power cable from the wall outlet, and notify your i3 support contact.
!!! Do not use the device with noticable damage to the power cables.
2. Only mount the i3SIXTY Display on the i3SIXTY F43-C Mobile Stand. Do not attempt to mount other devices.
3. Do not position the i3SIXTY F43-C Mobile Stand to be used on an inclining floor, not even with the wheel brakes locked.
The wheel brakes are not designed for this purpose.
4. Do not stand on the laptop tray, or use the Mobile Stand for any other purpose than specified in the usage instructions.
5. During assembly, do not rotate the display without first fully finishing the instructions. Do not rotate while any screw is still unfastened.
19 philips
Wrench Screw Driver
20 minutes 2 people
Required:
A B
C DE F
4x 1Hex Bolt M6 x 15 mm
Cross/Hex head
Hex Bolt M8 x 20 mm
Cross/Hex head
Tapered Bolt M8 x 14 mm
Cross head
8x 2
2x 3
2x 4Round Bolt M8 x 14 mm
Cross head
8x 5Round Bolt M5 x 8 mm
Cross head
4x 6Round Bolt M4 x 12 mm
Cross head
4x 7Washer M10
4x 8Split Lock Washer M10
4x 9Caster Wheels
4x 10 Spacer Bolts
2x 11 Cable Clips

Assemble the 4 wheels to each of the
4 legs.
Make sure that the brakes are locked
throughout the entire assembly
process.
Screw in the threaded bolt into the
bottom of the leg, through the wash-
ers (7 and 8).
Tightly fasten the wheels using a #19
wrench.
Assemble the legs (A and B) and the
tablet (C) together, with the M6x15
hex bolts (1).
Note that the backside of the tablet is
indicated with a shorter edge.
Having the wheels locked will help
keep the legs positioned.
Thightly fasten the bolts with a
wrench or cross screwdriver.
C
1
B
A
78

Mount the rotating display mount (D)
to the leg assembly,
with the 8x M8x20 hex bolts (2).
Make sure all bolts are tightly
fastened with a wrench or cross
screwdriver.
Feed the power cord through the
center hole of the rotating part.
At the front of the Mobile Stand, leave
450 mm of the power cord.
Fasten the power cord with the cable
clips (11) and M4x12 screws (6).
D
2
6
11
450 mm
2x
5

Insert the 4 spacers (10) and the top
2 mounting screws (4) into the VESA
300x300 mounting holes of the
i3SIXTY display.
Note that the i3SIXTY display will be
mounted in portrait orientation. Note
that the position of the i3SIXTY’s
camera is the top
Don’t screw in the bottom screws yet.
Leave the top screws at least 6 mm
unscrewed.
WARNING: DO NOT ROTATE THE DIS-
PLAY WITHOUT FULLY ASSEMBLING
THIS STEP.
Hang the display with the top screws
into the top keyholes of the Mobile
Stand.
Screw in the bottom 2 screws (3) into
the lower VESA 300x300 mounting
holes of the display.
6 mm
4
10
CAMERA
TOP
ATTENTION
2 people
DO NOT
carry alone
3

Assemble the 2 back covers (E & F)
behind the mounting plate.
Fasten the covers with 8 screws (5).
OPTIONAL:
If the display over- or under-rotates
(eg doesn’t finish the rotation
perfectly horizontal or vertical), you
can adjust the stopping points of the
rotation with the 4 screws located on
the mounting plate.
5

WWW.i3-TECHNOLOGIES.COM
[e-mail]
i3-TECHNOLOGIES