IBA ibaDAQ-C User manual

ibaDAQ-C
Manual
1
ibaDAQ-C
Compact Device for stand-alone Data Acquisition
Manual
Issue 1.4

Manual
ibaDAQ-C
Manufacturer
iba AG
Königswarterstr. 44
90762 Fürth
Germany
Contacts
Head office [phone]
Fax [phone]
Support [phone]
Technology [phone]
E-Mail: [e-mail]
Web: www.iba-ag.com
This manual must not be circulated or copied, or its contents utilized and disseminated, without
our express written permission. Any breach or infringement of this provision will result in liability
for damages.
© iba AG 2020, All rights reserved.
The content of this publication has been checked for compliance with the described hardware
and software. Nevertheless, deviations cannot be excluded completely so that the full compli-
ance is not guaranteed. However, the information in this publication is updated regularly. Re-
quired corrections are contained in the following regulations or can be downloaded on the Inter-
net.
The current version is available for download on our web site www.iba-ag.com.
Windows®is a label and registered trademark of the Microsoft Corporation. Other product and
company names mentioned in this manual can be labels or registered trademarks of the corre-
sponding owners.
Certification
The product is certified according to the European standards and directives. This product meets
the general safety and health requirements.
Further international customary standards and directives have been observed.
Note: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can radiate radio frequency energy and, if not in-
stalled and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Issue
Date
Version History
Chapter
Author
Version HW/FW
1.4
08/05/2020
Flash memory
10.1

ibaDAQ-C
Manual
Issue 1.4 3
Table of Contents
1About this manual...........................................................................................5
1.1 Target group.................................................................................................. 5
1.2 Notations....................................................................................................... 5
1.3 Used symbols................................................................................................ 6
2Introduction .....................................................................................................7
3Scope of delivery...........................................................................................10
4Safety instructions ........................................................................................ 11
4.1 Intended use ................................................................................................11
4.2 Special safety instructions ............................................................................11
5System requirements....................................................................................12
5.1 Hardware .................................................................................................... 12
6Mounting, dismounting, first configuration ................................................13
6.1 Mounting on a DIN rail................................................................................. 13
6.2 Dismounting ................................................................................................ 13
6.3 First configuration........................................................................................ 13
6.3.1 Setup via network........................................................................................ 13
6.3.2 Set up via monitor, keyboard and mouse..................................................... 15
7Device description ........................................................................................16
7.1 Views .......................................................................................................... 16
7.2 Display elements......................................................................................... 17
7.2.1 Operating state............................................................................................ 17
7.2.2 Operating state and user-defined displays .................................................. 17
7.3 Operating elements ..................................................................................... 18
7.3.1 ON/OFF switch S11..................................................................................... 18
7.3.2 Rotary switch S1 ......................................................................................... 18
7.4 Communication interfaces ........................................................................... 19
7.4.1 Network connection X21, X22 ..................................................................... 19
7.4.2 USB ports.................................................................................................... 19
7.4.3 DisplayPort X26 .......................................................................................... 19
7.5 Digital input X5 ............................................................................................ 19
7.6 Voltage supply X14...................................................................................... 20
7.7 Battery compartment X30............................................................................ 20
7.8 User accounts ............................................................................................. 21
8System integration ........................................................................................22
8.1 Configuration with ibaPDA client.................................................................. 22
8.2 Configuration with input devices .................................................................. 22
8.3 Remote Desktop ......................................................................................... 22
8.4 Connection to networks............................................................................... 23
8.5 Connection with USB-WLAN/RJ45 adapter................................................. 23
8.6 Operation with compact UPS ...................................................................... 23
9Configuration in ibaPDA...............................................................................24
9.1 Connection with an external ibaPDA client .................................................. 24

Manual
ibaDAQ-C
4 Issue 1.4
9.2 ibaDAQ-C configuration .............................................................................. 25
9.2.1 Configuration tab......................................................................................... 25
9.2.2 ibaDAQ-C – Info tab.................................................................................... 26
9.3 Add modules ............................................................................................... 28
9.4 Setting up file sharing.................................................................................. 29
9.4.1 Troubleshooting .......................................................................................... 30
10 Technical data ............................................................................................... 32
10.1 Main data .................................................................................................... 32
10.2 Interfaces .................................................................................................... 33
10.3 Dimensions ................................................................................................. 34
10.4 Connection diagram .................................................................................... 35
10.4.1 Pin assignment voltage supply X14............................................................. 35
10.4.2 Pin assignment digital input X5 ................................................................... 35
11 Index .............................................................................................................. 36
12 Contact and Support .................................................................................... 37

ibaDAQ-C
Manual
Issue 1.4 5
1 About this manual
This manual describes the layout, application and operation of the ibaDAQ-C device.
1.1 Target group
This manual addresses in particular the qualified professionals who are familiar with han-
dling electrical and electronic modules as well as communication and measurement tech-
nology. A person is regarded as a professional if he/she is capable of assessing safety
and recognizing possible consequences and risks on the basis of his/her specialist train-
ing, knowledge and experience and knowledge of the standard regulations.
1.2 Notations
The following designations are used in this manual:
Action Notations
Menu command Menu Logic diagram
Call of menu command Step 1 – Step 2 – Step 3 – Step x
Example:
Select menu Logic diagram – Add – New logic dia-
gram
Keys <Key name>
Example: <Alt>; <F1>
Press keys simultaneously <Key name> + <Key name>
Example:
<Alt> + <Ctrl>
Buttons <Button name>
Example:
<OK>; <Cancel>
File names, Paths „File name“, „Path”
Example:
„Test.doc“

Manual
ibaDAQ-C
6 Issue 1.4
1.3 Used symbols
If safety instructions or other notes are used in this manual, they mean:
The non
-
observance of this safety information may result in an imminent risk of death
or severe injury:
By an electric shock!
Due to the improper handling of software products which are coupled
to input and output procedures with control function!
The non
-
observance of this safety information may result in a potential risk of death or
severe injury!
The non
-
observance of this safety information may result in a potential risk of injury or
material damage!
Note
A note specifies special requirements or actions to be observed.
Important note
Note if some special features must be observed, for example exceptions from the rule.
Tip
Tip or example as a helpful note or insider tip to make the work a little bit easier.
Other documentation
Reference to additional documentation or further reading.

ibaDAQ-C
Manual
Issue 1.4 7
2 Introduction
ibaDAQ-C can be used as stand-alone unit to acquire and record data. ibaDAQ-C inte-
grates a complete ibaPDA system, an internal solid state disk (SSD) with sufficient
memory space and powerful integrated Intel®-Atom™-CPU. The extremely slim and ro-
bust compact unit is designed to fit into the extremely confined space of control cabinets,
test stands, cranes, etc.
The range of applications includes:
Mobile measurement acquisition
Start-up
Troubleshooting
Test stands
Calculation of process parameters
Data acquisition via Ethernet
ibaDAQ-C provides 2 independent Ethernet interfaces with standard 1 Gbit connection.
This allows ibaDAQ-C to capture and record Ethernet-based protocols. The license for
the communication interface ibaPDA-Interface-MQTT, for the MQTT messaging protocol,
as well as the ibaPDA-Interface-PLC-Xplorer license are part of the delivery. For other
protocols and modules, separate licenses are required for the respective communication
interfaces. Using the interfaces of ibaPDA-PLC-Xplorer, it is possible to aquire and rec-
ord data from different PLC systems:
S7-Xplorer (interface to SIMATIC S7 systems)
AB-Xplorer (interface to Allen-Bradley systems)
B&R-Xplorer (interface to B&R systems)
Bachmann-Xplorer (interface to M1 systems)
Codesys-Xplorer (interface to CODESYS based systems)
Logix-Xplorer (interface to ControlLogix systems)
MELSEC-Xplorer (interface to Mitsubishi MELSEC systems)
Sigmatek-Xplorer (interface to SIGMATEK systems)
TwinCAT-Xplorer (interface to Beckhoff systems)
Integrated cloud connectivity
With the included license ibaPDA-Data-Store-MindSphere-16, data can be written di-
rectly into the MindSphere cloud and processed there.
The license ibaPDA-Data-Store-MQTT-16 enables data streaming of 16 signals via the
MQTT messaging protocol and is also included in the scope of delivery.
Configuration
Equipped with connections for a monitor, mouse, and keyboard, ibaDAQ-C is as conven-
ient to operate as an ibaPDA system running on a computer. Moreover, it can be oper-
ated with an ibaPDA client connected via the network.
The ibaPDA version in ibaDAQ-C provides the full functional scope of ibaPDA and a
license for 64 signals in the standard version. The number of signals can be increased
to 1024 with a license extension.

Manual
ibaDAQ-C
8 Issue 1.4
Connection to several networks
With the two independent 1Gbit/s Ethernet interfaces, ibaDAQ-C can operate in two net-
works and thus enable the separation of IT and process networks. This separation al-
lows, for example, databases and storage systems to be connected to ibaDAQ-C, which
are located in the IT network.
Figure 1: Example of integration in 2 different networks
Communication interfaces included in delivery
Order no. Name Description
31.001042 ibaPDA-Interface-
PLC-Xplorer
Includes the communication interfaces:
- S7-Xplorer (interface to SIMATIC S7)
- AB-Xplorer (interface to Allen-Bradley systems)
- B&R-Xplorer (interface to B&R systems)
- Bachmann-Xplorer (interface to M1 systems)
- Codesys-Xplorer (interface to CODESYS based
systems)
- Logix-Xplorer (interface to ControlLogix systems)
- MELSEC-Xplorer (interface to Mitsubishi
MELSEC systems)
- Sigmatek-Xplorer (interface to SIGMATEK sys-
tems)
- TwinCAT-Xplorer (interface to Beckhoff systems)
31.001112 ibaPDA-Interface-
MQTT
MQTT communication interface
30.670051 ibaPDA-OPC-UA-
Server+
Advanced OPC UA server function
ibaPDA can be used as OPC UA server. This li-
cense allows access to all ibaPDA signals.
30.670180 ibaPDA-Data-Store-
MindSphere-16
Writing to the MindSphere cloud, 16 signals
30.671000 ibaPDA-Data-Store-
MQTT-16
Data-Streaming via MQTT: 16 signals

ibaDAQ-C
Manual
Issue 1.4 9
Examples for Ethernet based communication interfaces
(not included in delivery)
Order no. Name Description
31.001075 ibaPDA-Interface-
Generic-UDP
Generic-UDP/IP protocol communication interface
31.001076 ibaPDA-Interface-
Generic-TCP
Generic-TCP/IP protocol communication interface
Other documentation
For
the description and configuration of ibaPDA and the interfaces of ibaPDA-PLC-
Xplorer please refer to
the corresponding manuals.
You find the manuals on the DVD
“iba Software & Manuals” included in delivery.

Manual
ibaDAQ-C
10 Issue 1.4
3 Scope of delivery
After unpacking, check the delivery for completeness and possible damages.
The scope of delivery comprises:
ibaDAQ-C device
Covering caps for USB and Ethernet
2-pin connector with spring terminals (digital input, to initiate shutdown by UPS)
3-pin connector with spring terminals (voltage supply)
Manual (German and English)
"iba Software & Manuals" DVD