IBA ibaBM-FOX-i-3o-D User manual

ibaBM-FOX-i-3o-D
Optical Signal Multiplier
Manual
Issue 1.0

Manufacturer
iba AG
Koenigswarterstr. 44
90762 Fuerth
Germany
Contacts
Main office [phone]
Fax [phone]
Support [phone]
Engineering [phone]
E-Mail: [email protected]
Web: www.iba-ag.com
This manual must not be circulated or copied, or its contents utilized and disseminated,
without our express written permission. Any breach or infringement of this provision will
result in liability for damages.
©iba AG 2010, All Rights Reserved
The content of this publication has been checked for compliance with the described
hardware and software. Nevertheless, deviations cannot be excluded completely so
that the full compliance is not guaranteed. However, the information in this publication
is updated regularly. Required corrections are contained in the following regulations or
can be downloaded on the Internet.
The current version is available for download on our web site http://www.iba-ag.com.
Protection note
Windows is a label and registered trademark of the Microsoft Corporation. Other prod-
uct and company names mentioned in this manual can be labels or registered trade-
marks of the corresponding owners.
Certification
The device is certified according to the European standards and directives. This device
corresponds to the general safety and health requirements. Further international cus-
tomary standards and directives have been observed.

ibaBM-FOX-i-3o-D Manual
Issue 1.0 3
Table of contents
1About this manual.............................................................................................4
1.1 Target group......................................................................................................4
1.2 Designations .....................................................................................................4
1.3 Used symbols ...................................................................................................5
2Scope of delivery ..............................................................................................6
3Product properties............................................................................................6
3.1 Description........................................................................................................6
3.2 Functionality......................................................................................................6
3.3 Combination with other iba devices ..................................................................7
3.4 System Topologies............................................................................................8
3.5 Programming ....................................................................................................8
3.6 Device views.....................................................................................................9
3.7 Status LEDs (L1 to L4)......................................................................................9
4Mounting and Dismounting............................................................................10
4.1 Mounting .........................................................................................................10
4.2 Dismounting....................................................................................................10
5Technical data .................................................................................................11
5.1 Main data ........................................................................................................ 11
5.2 Dimensional Drawing......................................................................................12
6Support and contact .......................................................................................13

Manual ibaBM-FOX-i-3o-D
4 Issue 1.0
1 About this manual
This manual describes the construction, the use and the operation of the device
ibaBM-FOX-i-3o-D.
1.1 Target group
This manual addresses in particular the qualified professionals who are familiar with
handling electrical and electronic modules as well as communication and measurement
technology. A person is regarded to as professional if he/she is capable of assessing
safety and recognizing possible consequences and risks on the basis of his/her spe-
cialist training, knowledge and experience and knowledge of the standard regulations.
1.2 Designations
The following designations are used in this manual:
Action Designations
Menu command Menu „Logic diagram“
Call of menu command „Step 1 – Step 2 – Step 3 – Step x”
Example:
Select menu „Logic diagram – Add – New logic
diagram ”
Keys <Key name>
Example: <Alt>; <F1>
Press keys simultaneously <Key name> + <Key name>
Example:
<Alt> + <Ctrl>
Buttons <Button name>
Example:
<OK>; <Cancel>
File names, Paths „File name“, „Path”
Example:
„Test.doc“

ibaBM-FOX-i-3o-D Manual
1.3 Used symbols
If safety instructions or other notes are used in this manual, they mean:
The non-observance of this safety information may result in an imminent risk of death o
r
severe injury:
•By an electric shock!
•Due to the improper handling of software products which are coupled to input and
output procedures with control function!
If you do not observe the safety instructions regarding the process and the system o
r
machine to be controlled, there is a risk of death or severe injury!
The non-observance of this safety information may result in a potential risk of death o
r
severe injury!
The non-observance of this safety information may result in a potential risk of injury o
r
material damage!
Note
A note specifies special requirements or actions to be observed.
Important note
Note if some special features must be observed, for example exceptions from the rule.
Tip
Tip or example as a helpful note or insider tip to make the work a little bit easier.
Other documentation
Reference to additional documentation or further reading.
Issue 1.0 5

Manual ibaBM-FOX-i-3o-D
6 Issue 1.0
2
3
Scope of delivery
After unpacking you check the completeness and intactness of the delivery.
The scope of delivery includes:
TibaBM-FOX-i-3o-D
T2-pole Phoenix connector (for power supply)
TManual
Product properties
3.1 Description
The device ibaBM-FOX-i-3o-D (Fiber Optic Multiplier x3) is used for the distribution,
multiplication and recovery of optical signals used within the iba family of measurement
devices.
iba devices for data acquisition and signal conversion are typically connected via fiber
optics (ibaNet). This allows an easy handling of the connections (no termination resis-
tor networks) and provides a high signal-to-noise-ratio for data transmission. Moreover,
distributed data acquisition topologies may be built, as large as covering several
square miles.
A specific feature of the highly specialized ibaNet measurement network is the ability
that the star network topologies can work in uni-directional mode. Hence, the optical
signals may be multiplied by simply doubling the input data stream into several output
streams with identical information.
Concerning this fact redundant measurement systems using the same I/O infrastruc-
ture at different locations can easily be realized. This results in dramatic cost savings
that range from purchasing fewer devices to reduced planning and engineering costs.
The ibaBM-FOX-i-3o-D device features one fiber optic input and 3 fiber optic outputs.
The input data stream is simply copied to the outputs.
The input link of the device supports all ibaNet link protocols.
The device can also be used as a repeater if a cable length over 2 km (1.24 mls) is re-
quired.
3.2 Functionality
The device provides the following functions:
TDC 24 V power supply
T4 status LEDs
T1 fiber optic input
T3 fiber optic outputs
TSupports ibaNet link protocols 2.0 Mbit/s, 3.3 Mbit/s, 5.0 Mbit/s (only uni-
directional) and 32 Mbit/s
TSignal refreshing of the incoming data stream (bit refresh)
TDelay between input and output < 1 μs
TRugged design with DIN-rail snap mount

ibaBM-FOX-i-3o-D Manual
Issue 1.0 7
3.3 Combination with other iba devices
The following devices and boards of the iba product range may be used in combination
with ibaBM-FOX-i-3o-D:
TibaPADU-8/ -16/ -32
TibaPADU-8-O
TibaBM-SLM (SIMOLINK Monitor)
TibaBM-DDCS (ABB DDCS Bus)
TibaBM-DPM-S/-S-64 (Profibus)
TibaBM-CAN
TibaPADU-S-IT
TibaNet750-BM
TibaFOB-io-D (all models and former types)
TibaLink-SM-64-io (SIMATIC S5 (all types), MMC216)
TibaLink-SM-128V-i-2o (VME bus systems)
TibaBM-COL-8i-o
TibaBM-DIS-i-8o

Manual ibaBM-FOX-i-3o-D
8 Issue 1.0
3.4 System Topologies
The ibaBM-FOX-i-3o-D provides the ability to multiply fiber optical links. This is possi-
ble at each interconnection between iba devices, also between ibaPADU-8 and
ibaPADU-8-O devices.
Examples:
3.5 Programming
No programming or setting is necessary to operate the device.

ibaBM-FOX-i-3o-D Manual
3.6 Device views
1 Device status indicators (L1 to L4)
2 Main switch ON/OFF (S11)
3 Power supply DC 24 V (X14)
4 FO input RX (X10)
5 FO output TX (X30 to X32)
Figure 1: Device view
3.7 Status LEDs (L1 to L4)
The 4 LEDs indicate the device status.
LED Status Description
L1: green Blinking
Off
Device is working, power supply ok
Out of operation, no power supply
L2: yellow On Data transfer rate 2.0 Mbit/s, 3.3 Mbit/s or 5.0 Mbit/s detected on
input link
L3: white On Data transfer rate 32 Mbit/s detected on input link
L4: red Blinking Error
Issue 1.0 9

Manual ibaBM-FOX-i-3o-D
10 Issue 1.0
4 Mounting and Dismounting
4.1 Mounting
1. Insert the clip of the mounting rail fastened on the device into the mounting rail.
2. Press the device down in such a way that the clip of the mounting rail engages
with a click.
3. Observe the correct polarity of supply voltage. Connect the fiber optic cable to the
inputs and outputs.
4.2 Dismounting
1. Switch off the device and disconnect the power supply.
2. Disconnect all fiber optic cables.
3. Close the open inputs and outputs with a cover.
4. Hold the device to prevent it from falling down and press it slightly downwards.
5. After that pull the device and lift it up. The clip of the mounting rail will disengage
with a click.
6. When storing or transporting the device observe the values specified in the chap-
ter “Technical data”.

ibaBM-FOX-i-3o-D Manual
Issue 1.0 11
5 Technical data
5.1 Main data
Short description
Name ibaBM-FOX-i-3o-D
Description Optical multiplier
Order number 13.113501
Connections
ibaNet 1 Fiber optic input
3 Fiber optic outputs
FO cable
FO connectors 62.5/125 µm ST Lean Plug-in connector
Length FO line Max. 6562 ft (2000 m)
Baudrate 2.0 Mbit/s, 3.3 Mbit/s, 5.0 Mbit/s (only uni-
directional), 32 Mbit/s
Signal delay time From input to output: <1 μs
Supply, interfaces, operating and indicating elements
Power supply DC 24 V ±10%, unstabilized
Current consumption Max. 200 mA
Indicators 4 LED for device status
Operating and environmental conditions
Cooling Passive
Operating temperature 32 °F to 122 °F (0 °C to 50 °C)
Storage and transport temperature -13 °F to 158 °F (-25 °C to 70 °C)
Mounted orientation Vertical
Installation altitude Up to 6,562 ft (2000 m)
Assembly Snapped on to a DIN rail
Humidity class DIN 40040 F, no condensation
Protection class IP20
CE conformity EMI: EN 61326-1
Dimensions and weight
Dimensions (width x height x depth) 1.30 in x 7.44 in x 5.94 in
(33 mm x 189 mm x 151 mm) with DIN-rail clip
Weight (incl. box and documenta-
tion) 1.65 lb (0,75 kg)

Manual ibaBM-FOX-i-3o-D
12 Issue 1.0
5.2 Dimensional Drawing
(Dimensions given in mm)
Figure 2: Dimension drawing

ibaBM-FOX-i-3o-D Manual
Issue 1.0 13
6 Support and contact
Support
Phone: [phone]
Fax: [phone]
E-Mail: [email protected]
Note
If you require support, specify the serial number (iba-S/N) of the product.
Contact
Headquarters
iba AG
Koenigswarterstr. 44
90762 Fuerth
Germany
Phone: [phone]
Fax: [phone]
Email: [email protected]
Contact: Mr. Harald Opel
Regional and Worldwide
For contact data of your regional iba office or representative please refer to our web
site
www.iba-ag.com.