IBASE Technology IP315 User manual

IP315
Backplane for PICMG 1.3
User’s Manual
Version 1.0
(JAN 2020)

ii IP315 User’s Manual
Copyright
© 2019 IBASE Technology, Inc. All rights reserved.
No part of this publication may be reproduced, copied, stored in a retrieval system,
translated into any language or transmitted in any form or by any means,
electronic, mechanical, photocopying, or otherwise, without the prior written
consent of IBASE Technology, Inc. (hereinafter referred to as “IBASE”).
Disclaimer
IBASE reserves the right to make changes and improvements to the products
described in this document without prior notice. Every effort has been made to
ensure the information in the document is correct; however, IBASE does not
guarantee this document is error-free.
IBASE assumes no liability for incidental or consequential damages arising from
misapplication or inability to use the product or the information contained herein,
nor for any infringements of rights of third parties, which may result from its use.
Trademarks
All the trademarks, registrations and brands mentioned herein are used for
identification purposes only and may be trademarks and/or registered trademarks
of their respective owners.

IP315 User’s Manual
iii
Compliance
In a domestic environment, this product may cause radio interference in which
case users may be required to take adequate measures.
This product has been tested and found to comply with the limits for a Class A
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with manufacturer’s instructions, may cause
harmful interference to radio communications.
WEEE
This product must not be disposed of as normal household
waste, in accordance with the EU directive of for waste
electrical and electronic equipment (WEEE - 2012/19/EU).
Instead, it should be disposed of by returning it to a
municipal recycling collection point. Check local
regulations for disposal of electronic products.
Green IBASE
This product is compliant with the current RoHS
restrictions and prohibits use of the following substances
in concentrations exceeding 0.1% by weight (1000 ppm)
except for cadmium, limited to 0.01% by weight (100 ppm).
• Lead (Pb)
• Mercury (Hg)
• Cadmium (Cd)
• Hexavalent chromium (Cr6+)
• Polybrominated biphenyls (PBB)
• Polybrominated diphenyl ether (PBDE)

iv IP315 User’s Manual
Important Safety Information
Carefully read the precautions before using the board.
Environmental conditions:
•Use this product in environments with ambient temperatures between -20˚C
and 70˚C.
•Do not leave this product in an environment where the storage temperature
may be below -40° C or above 90° C. To prevent from damages, the product
must be used in a controlled environment.
Care for your IBASE products:
•Before cleaning the PCB, unplug all cables and remove the battery.
•Clean the PCB with a circuit board cleaner, degreaser, or use cotton swabs
and alcohol.
•Vacuum the dust with a computer vacuum cleaner to prevent the fan from
being clogged.
WARNING.
Attention during use:
•Do not use this product near water.
•Do not spill water or any other liquids on this product.
•Do not place heavy objects on the top of this product.
Anti-static precautions
•Wear an anti-static wrist strap to avoid electrostatic discharge.
•Place the PCB on an anti-static kit or mat.
•Hold the edges of PCB when handling.
•Touch the edges of non-metallic components of the product instead of the
surface of the PCB.
•Ground yourself by touching a grounded conductor or a grounded bit of metal
frequently to discharge any static.
CAUTION
Danger of explosion if the internal lithium-ion battery is replaced by an incorrect
type. Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer’s
instructions or recycle them at a local recycling facility or battery collection point.

IP315 User’s Manual
v
Warranty Policy
•IBASE standard products:
24-month (2-year) warranty from the date of shipment. If the date of shipment
cannot be ascertained, the product serial numbers can be used to determine
the approximate shipping date.
•3
rd
-party parts:
12-month (1-year) warranty from delivery for the 3rd-party parts that are not
manufactured by IBASE, such as CPU, CPU cooler, memory, storage
devices, power adapter, panel and touchscreen.
＊ PRODUCTS, HOWEVER, THAT FAIL DUE TO MISUSE, ACCIDENT,
IMPROPER INSTALLATION OR UNAUTHORIZED REPAIR SHALL BE
TREATED AS OUT OF WARRANTY AND CUSTOMERS SHALL BE BILLED
FOR REPAIR AND SHIPPING CHARGES.
Technical Support & Services
1. Visit the IBASE website at www.ibase.com.tw to find the latest information
about the product.
2. If you need any further assistance from your distributor or sales
representative, prepare the following information of your product and
elaborate upon the problem.
•Product model name
•Product serial number
•Detailed description of the problem
•The error messages in text or in screenshots if there is any
•The arrangement of the peripherals
•Software in use (such as OS and application software, including the
version numbers)
3. If repair service is required, you can download the RMA form at
http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and
contact your distributor or sales representative.

vi IP315 User’s Manual
Table of Contents
Chapter 1 General Information ............................................. 1
1.1 Introduction .........................................................................................2
1.2 Features..............................................................................................2
1.3 Specifications ...................................................................................... 3
1.4 Overview .............................................................錯誤! 尚未定義書籤。
1.5 Dimensions .........................................................................................5
Chapter 2 Hardware Configuration.......................................... 6
2.1 Setting the Jumpers ............................................................................7
2.2 Connector Locations on IP315 ............................................................ 8
2.3 Jumpers Quick Reference ...................................................................9
2.3.1 USB 2.0 Connector (USB1,USB2).............................................9
2.3.2 ATX Power ON Pin Header (J3) .................................................9
2.3.3 Reset Pin Header (J4)................................................................9
2.4 Connectors Quick Reference.............................................................11
2.4.1 ATX Power Connector (J1)...................................................... 11
2.4.2 ATX 12V Power Connector (ATX_12V_2X1) ........................... 12
2.4.3 System Fan Power Connector (FAN1,FAN2) .......................... 12
2.4.4 SHB Express™ Connector Pinout(BP_CONNA1, BP_CONNB1,
BP_CONNC1,BP_CONND1)............................................................... 12
2.4.5 PCI Routing (PCI1,PCI2,PCI3,PCI4) ........................................ 14

IP315 User’s Manual
vii
This page is intentionally left blank.

1
Chapter 1
General Information
The information provided in this chapter includes:
•Features
•Specifications
•Board Picture
•Board Dimensions

2 IP315
User’s Manual
1.1 Introduction
IP315 is a Backplane for PICMG 1.3 CPU module. Measuring 310 mm x 327
mm (12.2” x 12.9”), it provides expansion slots connectors including one
PICMG 1.3 slot, one PCIe(16x) slot (x8 signal), two PCIe(8x) slot (x4 signal),
four PCIe(4x) slot (x1 signal), four PCI slot, two USB 2.0, and two SATA3.0.
Photo of IP315
1.2 Features
•1 x PICMG 1.3 slot
•1 x PCIe(16x) slot (x8 signal)
•2 x PCIe(8x) slot (x4 signal)
•4 x PCIe(4x) slot (x1 signal)
•4 x PCI slot
•2 x USB 2.0 (2x 4-pin header)
•2 x SATA3.0,

General Information
IP315 User’s Manual 3
1
1.3 Specifications
Product Name IP315
Form Factor Backplane for PICMG 1.3 CPU Card
Onboard Slots
- PICMG 1.3 slot x 1
- PCIe(16x) slot x 1 (x8 signal)
- PCIe(8x) slot x 2 (x4 signal)
- PCIe(4x) slot x 4 (x1 signal)
- PCI slot x 4
Onboard
header/Connector
- 2x 4-pin header x 2 for USB 2.0 ports*4
- 2x 10 pins box header x 1 (Reserved)
- 2x SATA3.0 connector
- 2x 4-pin box header
Power Connector
24-pin ATX power connector x1
8pin power connector x 1(for 12V)
3-pin type fan connector x 2
Operating
Temperature 0°C ~ 60°C (32°F ~140°F)
Others Validated with IB995
RoHS2.0 Yes
PCB Layer 4 Layers
Board Size 310mm x 327mm (12.2” x 12.9”)

4 IP315
User’s Manual
1.4 Board Picture
Top View

General Information
IP315 User’s Manual
5
1
1.5 Dimensions

6
Chapter 2
Hardware Configuration
This section provides information on jumper settings and connectors
on the board in order to set up a workable system.
•Jumper and connector locations
•Jumper settings and information of connectors

IP315 User’s Manual
7
2.1 Setting the Jumpers
Set up and configure your board by using jumpers for various settings and
features according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your use.
2.2.1 How to Set Jumpers
Jumpers are short-length conductors consisting of several metal pins with a
non-conductive base mounted on the circuit board. Jumper caps are used to have
the functions and features enabled or disabled. If a jumper has 3 pins, you can
connect either PIN1 to PIN2 or PIN2 to PIN3 by shorting.
Pin# 1 2
3
A 3-pin jumper A jumper cap
Refer to the illustration below to set jumpers.
Pin closed Oblique view Schematic illustration
Open
1 2 3
1-2
1 2 3
2-3
1 2 3
When two pins of a jumper are encased in a jumper cap, this jumper is closed, i.e.
turned On.
When a jumper cap is removed from two jumper pins, this jumper is open, i.e.
turned Off.

8 IP315 User’s Manua
l
2.2 Connector Locations on IP315
Board diagram of IP315

IP315 User’s Manual 9
2.3 Jumpers Quick Reference
Function Jumper Name
USB 2.0 Connector USB1,USB2
ATX Power ON Pin Header J3
Reset Pin Header J4
2.3.1 USB 2.0 Connector (USB1, USB2)
21
5
3
6
4
87
Pin Signal Name Pin Signal Name
1 VCC 2 Ground
3 D0- 4 D1+
5 D0+ 6 D1-
7 Ground 8 VCC
2.3.2 ATX Power ON Pin Header (J3)
The 2 pins make an “ATX Power Supply On/Off Switch” for the
system that connects to the power switch on the case. When
pressed, the power switch will force the system to power on.
When pressed again, it will power off the system.
2.3.3 Reset Pin Header (J4)
The reset switch allows you to reset the system without turning
the main power switch off and then on again. Orientation is not
required when making a connection to this header.
1
1

10 IP315 User’s Manua
l

IP315 User’s Manual 11
2.4 Connectors Quick Reference
Function Connector Name
ATX Power Connector J1
ATX 12V Power Connector ATX_12V_2X1
System Fan Power Connector FAN1,FAN2
SHB Express™Connector Pinout
BP_CONNA1,
BP_CONNB1,
BP_CONNC1,
BP_CONND1
PCI Routing (PCI1,PCI2,PCI3,PCI4)
2.4.1 ATX Power Connector (J1)
Pin Signal Name Pin Signal Name
1 3.3V 13 3.3V
2 3.3V 14 -12V
3 Ground 15 Ground
4 +5V 16 PS-ON
5 Ground 17 Ground
6 +5V 18 Ground
7 Ground 19 Ground
8 Power good 20 -5V
9 5VSB 21 +5V
10 +12V 22 +5V
11 +12V 23 +5V
12 3.3V 24 Ground

12 IP315 User’s Manua
l
2.4.2 ATX 12V Power Connector (ATX_12V_2X1)
8
4
1
5
Pin Signal Name Pin Signal Name
1 Ground 5 +12V
2 Ground 6 +12V
3 Ground 7 +12V
4 Ground 8 +12V
2.4.3 System Fan Power Connector (FAN1, FAN2)
1
Pin Signal Name Pin Signal Name
1 Ground 3 NC
2 +12V
2.4.4 SHB Express™Connector Pinout(BP_CONNA1,
BP_CONNB1, BP_CONNC1,BP_CONND1)
x16 PCIe Connector A x8 PCIe Connector B x16 PCIe Connector C x8 PCIe Connector D
Pin Side B Side A Pin Side B Side A Pin Side B Side A Pin Side B Side A
1 SMCLK SMDAT 1 +5Vaux
+5Vaux 1 1USB0P GND 1 1INTB# INTA#
2 GND GND 2 GND RSVD 2 USB0N GND 2 INTD# INTC#
3 TDI(NC)
TCK(NC)
3
a_PETp8
GND
a_PETp8
GND
3 GND USB1P 3 GND VIO(NC)
4 TDO(NC)
TMS(NC)
4
a_PETn8
GND
a_PETn8
GND
4 GND USB1N 4 REQ3# GNT3#
5 TRST#(N
C)
WAKE#
5 GND a_PERp8 5 USB2P GND 5 REQ2# GNT2#
6 PWRBT#
PME#(NC)
6 GND a_PERn8 6 USB2N GND 6 PCI_RST
#
GNT1#
7 PWRGD
PSON#
7 a_PETp9
GND
7 GND USB3P 7 REQ1# GNT0#
8 SHB_RS
T#
PERST#
8 a_PETn9
GND
8 GND USB3N 8 REQ0# SERR#
9 CFG0 CFG1(NC) 9 GND a_PERp9 9 USBOC0#
GND
9 SDONE +3.3V
10
CFG2 CFG3
10
GND a_PERn9
10
GND USBOC1#
10
GND CLKFI(NC)
11
RSVD GND
11
RSVD GND
11
USBOC2# GND
11
CLKFO
(NC)
GND
12
GND RSVD
12
GND RSVD
12
GND USBOC3#
12
CLKC CLKD
13
b_PETp0 GND
13
a_PETp1
0 GND
a_PETp10
GND
13
SATAHT0
P
GND
13
GND +3.3V
14
b_PETn0 GND
14
a_PETn1
0 GND
a_PETn10
GND
14
SATAHT0
N GND
SATAHT0
N GND
14
CLKA CLKB
15
GND b_PERp0
15
GND a_PERp10
15
GND SATAHR0
P
15
+3.3V GND