Advantech DVP-7010BE User manual

DVP-7010BE
4 Channel PCI-bus
Surveillance
Capture card

DVP-7010BE User’s Manual
2
Copyright
This documentation and the software included with this product
are copyrighted in 2006 by Advantech Co., Ltd. All rights are
reserved. Advantech Co., Ltd. reserves the right to make
improvements in the products described in this manual at any time
without notice. No part of this manual may be reproduced, copied,
translated or transmitted in any form or by any means without the
prior written permission of Advantech Co., Ltd. Information
provided in this manual is intended to be accurate and reliable.
ADVANTECH CO., LTD. assumes no responsibility for its use, nor
for any infringements of the rights of third parties which may result
from its use.
Acknowledgments
IBM and PC are trademarks of International Business Machines
Corporation. MS-DOS, Windows, Microsoft Visual C++ and Visual
BASIC are trade-marks of Microsoft Corporation. Intel and Pentium
are trademarks of Intel Corporation. Delphi and C++ Builder are
trademarks of Inprise Corporation.
CE notification
The DVP-7010BE, developed by ADVANTECH CO., LTD., has
passed the CE test for environmental specifications when shielded
cables are used for external wiring. We recommend the use of
shielded cables. This kind of cable is available from Advantech.
Please contact your local supplier for ordering information
On-line Technical Support
For technical support and service, please visit our support website
at: http://www.advantech.com/support
PartNo.2062701010 1stEdition
Printed in Taiwan July.2006
Rev. 1.00

3
CHAPTER
1
General Information

DVP-7010BE User’s Manual
4
Chapter 1 General Information
DVP-7010BE is 4 channel input, PCI-bus video capture card. It supports
up to 4 channel input by share-frame technology and captures up to D1
resolution at 30/25 fps frame rate. DVP-7010BE supports NTSC/PAL
composite video input through BNC connectors and digitizes the data to
PC through PCI bus. The DVP-7010BE is a digital video surveillance card
with SDK (software develop kit).It provides 4 pairs GPIO for user any kind
application needs.
1.1 HardwareRequirement
Intel Pentium III 1GHz or above (CPU speed depends on
video frame rate, channels and resolution)
256 MB RAM or above
Free PCI slot(s)
CD-ROM
Hard disk with 1G free space
1.2 Software Requirement
Microsoft Windows XP with DirectX 9.0 or above

5
1.3 BlockDiagram
Figure 1.1 System diagram
1.4 Packing List
DVP-7010BE PCI capture card X 1
Utility CD (Driver, Manual, SDK, Sample, Sample source code) X 1
Connection cable for WDT X 1

DVP-7010BE User’s Manual
6
1.5 Dimensions
Figure 1.2 Dimensions

7
1.6 Connector location
Figure 1.3 connector location
GPIO: J1
Video input
for ODM
customer only

DVP-7010BE User’s Manual
8
1.7 Pin definition
1.7.1 GPIO: J1
•8 bit TTL/CMOS level Digital I/O.
GPIO (J1) Pin define
Pin no. Description
Pin 1 OUT0
Pin 2 OUT1
Pin 3 OUT2
Pin 4 OUT3
Pin 5 IN0
Pin 6 IN1
Pin 7 IN2
Pin 8 IN3
Pin 9 VCC
Pin 10 GND
Table 1.1 GPIO J1 pin definition
Figure 1.4 GPIO(J1) pin definition

9
1.8 HardwareInstallation
1 Turn off your computer and unplug the power cord.
2 Remove the cover of your computer.
3 Touch the metal part on the surface of your computer to
neutralize the static electricity that might be on your body.
4 Place the DVP-7010BE into Mother Board PCI slot.
5 Connect appropriate accessories (Video cable to camera. if
necessary) to the DVP-7010BE.
6 Replace the cover of your computer chassis.
7 Plug in the power cord and turn on the computer.
Note: Keep the anti-static bag for future use. You might need the original bag
to store the card if you have to remove the card from the PC or transport it
elsewhere.
1.9 Software / Driver Installation
Before you begin
To facilitate the installation of the enhanced display device drivers
and utility software, you should read the instructions in this chapter
carefully before you attempt installation. The device drivers for the
DVP-7010BE board are located on the software installation CD.
The auto-run function of the driver CD will guide and link you to the
utilities and device drivers under Windows system. Before you
begin, it is important to note that most display drivers need to have
the relevant software application already installed in the system
prior to installing the enhanced display drivers. In addition, many of
the installation procedures assume that you are familiar with both
the relevant software applications and operating system
commands. Review the relevant operating system commands and
the pertinent sections of your application software user’s manual
before performing the installation.

DVP-7010BE User’s Manual
10
Installation
Step 1: Pop-up the “System Properties” window, choose the
“Hardware” page, and press the “Device Manager” bottom.