IBM 00AE861 Manual

IBM High IOPS Adapter
Hardware Installation Guide
FOR IOMEMORY VSL 3.2.3
SEPTEMBER 23, 2013
- 1 -
[no notes on this page]

IBM High IOPS Adapter Hardware Installation Guide for ioMemory VSL 3.2.2 |______ _ _ 2
IBM High IOPS Hardware Installation Guide for ioMemory VSL 3.2.3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Software Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
IBM Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Hardware Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
In the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installing the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Half-Height Bracket Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Power Cables for Second Generation IBM High IOPS Duo Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
IBM Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
- 2 -
[no notes on this page]

IBM High IOPS Adapter Hardware Installation Guide for ioMemory VSL 3.2.2 |______ _ _ 3
IBM High IOPS Hardware Installation Guide for ioMemory VSL 3.2.3
Legal Notices
© Copyright International Business Machines 2013. All rights reserved.
© Copyright 2006-2013 Fusion-io, Inc. All rights reserved. Fusion-io is a trademark of Fusion-io, Inc.
Part Number: D0003073-003_3
: September 23, 2013Published
- 3 -
[no notes on this page]

IBM High IOPS Adapter Hardware Installation Guide for ioMemory VSL 3.2.2 |______ _ _ 4
1.
2.
3.
4.
5.
1.
2.
3.
4.
Safety Information
DANGER
Electrical current from power, telephone, and communication cables is hazardous.
To avoid a shock hazard:
Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this
product during an electrical storm.
Connect all power cords to a properly wired and grounded electrical outlet.
Connect to properly wired outlets any equipment that will be attached to this product.
When possible, use one hand only to connect or disconnect signal cables.
Never turn on any equipment when there is evidence of fire, water, or structural damage.
Disconnect the attached power cords, telecommunications systems, networks, and modems before you open
the device covers, unless instructed otherwise in the installation and configuration procedures.
Connect and disconnect cables as described in the following table when installing, moving, or opening covers on this
product or attached devices.
To Connect To Disconnect
Turn everything OFF.
First, attach all cables to devices.
Attach signal cables to connectors.
Attach power cords to outlet.
Turn device ON.
Turn everything OFF.
First, remove power cords from outlet.
Remove signal cables from connectors.
Remove all cables from devices.
- 4 -
[no notes on this page]

IBM High IOPS Adapter Hardware Installation Guide for ioMemory VSL 3.2.2 |______ _ _ 5
Introduction
Overview
Congratulations on your purchase of an IBM solid-state storage device. This guide explains how to install your IBM
High IOPS Adapter.
For information on installing software for your device, consult the for your operatingIBM ioMemory VSL User Guide
system.
NOTE Throughout this manual, when you see a reference to an , you may substituteIBM High IOPS Adapter
your particular device(s) ., such as an IBM High IOPS Adapter or an IBM High IOPS Duo Adapter
Software Compatibility
Compatible Software (Driver)
The ioMemory VSL software is more than just a hardware driver, it is the "secret sauce" that gives IBM High IOPS
Adapters their amazing performance. Each release of the ioMemory VSL software is compatible with certain IBM
High IOPS Adapters.
For a list of devices that are compatible with the version of the ioMemory VSL software that you are installing, consult
the for that version.IBM ioMemory VSL Release Notes
Compatible Operating Systems
The operating system requirements depends on the version of ioMemory VSL software that you are installing with this
device.
For more information, consult the for the version you wish to install.IBM ioMemory VSL Release Notes
- 5 -
[no notes on this page]

IBM High IOPS Adapter Hardware Installation Guide for ioMemory VSL 3.2.2 |______ _ _ 6
IBM Adapters
Enterprise Value IBM Flash Adapters
Feature
Code
Option
Part
Number
Description PCIe Slot
Required
Controller
Throttle
Temp.
Controller
Shutdown
Temp
NAND
Board
Throttle
Temp.
NAND Board
Shutdown
Temp.
A4WR 00AE861 IBM Flash Adapter F825
Enterprise Value for
System x
Gen2 x8*
Half-height,
half-length
clearance
78°C 85°C 78°C 83°C
A4WS 00AE864 IBM Flash Adapter
F1650 Enterprise Value
for System x
Gen2 x8*
Half-height,
half-length
clearance
78°C 85°C 78°C 83°C
A4WT 00AE867 IBM Flash Adapter
F3200 Enterprise Value
for System x
Gen2 x8*
Full-height,
half-length
clearance
93°C 100°C 78°C 83°C
* Gen2 x8 slot with at least 4 lanes that are electrically active.
Memory Attributes
Feature
Code
NAND
Type [1]
Total
Memory
Memory
Modules
Module
Capacity
Maximum writes per
memory module
Maximum writes
per card
A4WR MLC 825GB 1 825GB 4PB 4PB
A4WS MLC 1650GB 1 1650GB 8PB 8PB
A3DY MLC 3.20TB 1 3.20TB 20PB 20PB
1. Single Level Cell (SLC), Multi Level Cell (MLC).
- 6 -
[no notes on this page]

IBM High IOPS Adapter Hardware Installation Guide for ioMemory VSL 3.2.2 |______ _ _ 7
Second Generation Adapters
IBM High IOPS Adapter Options
Feature
Code
Option
Part
Number
Description PCIe Slot
Required
Controller
Throttle
Temp.
Controller
Shutdown
Temp
NAND
Board
Throttle
Temp.
NAND Board
Shutdown
Temp.
A3J3 46C9078 IBM 365GB High
IOPS MLC Mono
Adapter
Gen2 x8
Half-height,
half-length
clearance
93°C 100°C 78°C 83°C
A3J4 46C9081 IBM 785GB High
IOPS MLC Mono
Adapter
Gen2 x8
Half-height,
half-length
clearance
93°C 100°C 78°C 83°C
A3DY 90Y4377 IBM 1.2TB High
IOPS MLC Mono
Adapter
Gen2 x8
Half-height,
half-length
clearance
93°C 100°C 78°C 83°C
A3DZ 90Y4397 IBM 2.4TB High
IOPS MLC Duo
Adapter
Gen2 x8
Full-height,
half-length
clearance
93°C 100°C 78°C 83°C
Memory Attributes
Feature
Code
NAND
Type [1]
Total
Memory
Memory
Modules
Module
Capacity
Maximum writes per
memory module
Maximum writes
per card
A3J3 MLC 365GB 1 365GB 4PB 4PB
A3J4 MLC 785GB 1 785GB 11PB 11PB
A3DY MLC 1.2TB 1 1.2TB 17PB 17PB
A3DZ MLC 2.4TB 2 1.2TB 17PB 34PB [2]
1. Single Level Cell (SLC), Multi Level Cell (MLC).
2. Assumes uniform distribution of writes across both memory modules.
- 7 -
[no notes on this page]

IBM High IOPS Adapter Hardware Installation Guide for ioMemory VSL 3.2.2 |______ _ _ 8
Legacy Devices
IBM High IOPS Adapter Options
Feature
Code
Option Part
Number
Description PCIe Slot
Required
Controller
Throttle Temp.
Controller
Shutdown Temp.
0096 46M0877 IBM 160GB High IOPS SS Class
SSD PCIe Adapter
Gen1 x4
Half-height,
half-length clearance
78°C 85°C
0097 46M0878 IBM 320GB High IOPS SD Class
SSD PCIe Adapter
Gen1 x8 or Gen2 x4
Half-height,
half-length clearance
78°C 85°C
1649 46M0898 IBM 320GB High IOPS MS Class
SSD PCIe Adapter
Gen1 x4
Half-height,
half-length clearance
78°C 85°C
5985 81Y4519 640GB High IOPS MLC Duo
Adapter for IBM System x
Gen1 x8 or Gen2 x4
Full-height,
half-length clearance
78°C 85°C
A1NE 81Y4535 320GB High IOPS SLC Adapter for
IBM system x
Gen1 x4
Half-height,
half-length clearance
78°C 85°C
A1ND 81Y4539 640GB High IOPS SLC Duo
Adapter for IBM System x
Gen1 x8 or Gen2 x4
Full-height,
half-length clearance
78°C 85°C
A1NC 81Y4531 640GB High IOPS MLC Adapter
for IBM System x
Gen1 x4
Half-height,
half-length clearance
78°C 85°C
A1NB 81Y4527 1.28TB High IOPS MLC Duo
Adapter for IBM System x
Gen1 x8 or Gen2 x4
Full-height,
half-length clearance
78°C 85°C
- 8 -
[no notes on this page]

IBM High IOPS Adapter Hardware Installation Guide for ioMemory VSL 3.2.2 |______ _ _ 9
Memory Attributes
Feature
Code
NAND
Type [1]
Total
Memory
Memory
Modules
Module
Capacity
Maximum writes per
memory module
Maximum writes
per card
0096 SLC 160GB 1 160GB 75PB 75PB
0097 SLC 320GB 2 160GB 75PB 150PB [2]
1649 MLC 320GB 1 320GB 4PB 4PB
5985 MLC 640GB 2 320GB 4PB 8PB [2]
A1NE SLC 320GB 1 320GB 50PB 50PB
A1ND SLC 640GB 2 320GB 50PB 100PB [2]
A1NC MLC 640GB 1 640GB 10PB 10PB
A1NB MLC 1.28TB 2 640GB 10PB 20PB [2]
1. Single Level Cell (SLC), Multi Level Cell (MLC).
2. Assumes uniform distribution of writes across both memory modules.
Hardware Requirements
NOTE For the latest IBM System x server configuration information and requirements for IBM High IOPS Mono
and Duo Adapters, please see the URL below:
http://www.ibm.com/support/entry/portal/docdisplay?lndocid=SERV-IOPS
Shipping Considerations
Legacy Adapters:
Legacy High IOPS adapters do not support shipping installed or transported inside IBM System x servers. The Legacy
adapters must be packaged in the original box, electrostatic discharge (ESD) bag and packing materials. An alternate
packaging equivalent intended for fragile ESD sensitive electronic devices may also be used. Configured Legacy
adatpers must be removed and repackaged before shipping. For more information, see the following websites:
High IOPS adapter shipping requirements: http://www.ibm.com/support/entry/portal/docdisplay?lndocid=migr-5092425
Second Generation Adapters:
Shipping considerations for Second Generation High IOPS adapters are maintained at the following website:
IBM High IOPS System x server configuration information and requirements:
http://www.ibm.com/support/entry/portal/docdisplay?lndocid=SERV-IOPS
- 9 -
[no notes on this page]

IBM High IOPS Adapter Hardware Installation Guide for ioMemory VSL 3.2.2 |______ _ _ 10
1.
2.
Adequate Power for Second Generation IBM High IOPS Duo Adapters
Second Generation IBM High IOPS Duo Adapters require more power than the minimum 25W provided by PCIe
Gen2 slots to properly function, and therefore receive additional power via the included power cable.must
Without additional power, function will be limited with Second Generation IBM High IOPS Duo Adapters. For more
information on providing additional power via a power cable, see Power Cables for Second Generation IBM High IOPS Duo
.Adapters $body
Adequate System Cooling
300 LFM: To maximize the longevity and performance of IBM High IOPS Adapters, we recommend at least 300
Linear Feet per Minute (LFM) of airflow across the devices.
55°C Maximum: The ambient air temperature around the device should not exceed 55°C.
Device Thermal Monitoring: In order to protect against thermal damage, all IBM High IOPS Adapters monitor the
temperature of its onboard controller chip (This is reported by the command-line utility as "Internalfio-status
temperature"). Newer devices, such as IBM High IOPS Adapters, also monitor the NAND boards to prevent
overheating of the NAND flash components. If your device is throttled or shuts down due to thermal issues, the
ioMemory VSL software will log the event in the system logs.
In an attempt to contain temperatures within an optimal range, the ioMemory VSL software will start throttling
write performance once the controller temperature or NAND board reaches a set temperature.
If the controller or NAND board temperature continues to rise, the software will shut down the device once
the maximum operating temperature is reached.
The throttling and shutdown temperature depends on the device. Some devices detect the NAND board temperature,
while others do not.
To find these temperatures limits for your device, find your device in the section.IBM Adapters
Attention : If your BIOS has a High Performance/Power Mode, enable it whenHigh Performance/Power Mode
using IBM High IOPS Adapters. Also disable any power-saving modes. This improves performance in two
ways:
Prevents operating systems and the BIOS from suspending PCIe devices (using ASPM), including IBM High
IOPS Adapters. IBM High IOPS Adapters do not support ASPM.
Maintains higher fan speeds to prevent thermal throttling.
- 10 -
[no notes on this page]

IBM High IOPS Adapter Hardware Installation Guide for ioMemory VSL 3.2.2 |______ _ _ 11
Sufficient System Memory (RAM)
The ioMemory VSL software requires enough RAM to accelerate your IBM High IOPS Adapter. The RAM
requirements depend on how your operating system tracks I/O's (average written block sizes), the capacity of your
IBM High IOPS Adapters, and the version of the ioMemory VSL software.
For more information, including a chart on RAM required per GB of IBM High IOPS Adapter capacity, consult the
for the version of ioMemory VSL software that you will install with the device(s).IBM ioMemory VSL Release Notes
Firmware Requirements
Your IBM High IOPS Adapter may have a minimum firmware label affixed (for example, "MIN FW: XXXXXX").
This label indicates the minimum version of the firmware that is compatible with your device.
NOTE For firmware and upgrade considerations, consult the for the version youIBM ioMemory VSL Release Notes
wish to install.
Attention Do not downgrade the IBM High IOPS Adapter to an earlier version of the firmware. Earlier versions of
the firmware may not be compatible with the device, and downgrading the firmware will result in data loss.
In the Box
Your IBM High IOPS Adapter comes with these items:
IBM High IOPS Adapter
Quick Start Instructions
IBM High IOPS Adapter half-height bracket (used on low-profile systems; the IBM High IOPS Duo Adapter
does not use a half-height bracket).
USB Key
On the USB Key are the following items:
Environmental Notices document
Important Notices document
Second Generation IBM High IOPS Adapters come with:
External Power Cable
- 11 -
[no notes on this page]

IBM High IOPS Adapter Hardware Installation Guide for ioMemory VSL 3.2.2 |______ _ _ 12
1.
2.
3.
Installing the Device
NOTE Please read the if you have not done so.Hardware Requirements
Attention : If you have IBM High IOPS Adapters configured for ioMemory VSLUpgrade Previous Devices First
2.x or earlier that you wish to use with ioMemory VSL software version 3.x, you must upgrade the firmware
on the previously installed devices before installing new devices in the system. See the IBM ioMemory VSL
for full Upgrade Notes.Release Notes
Installation Instructions
Attention Electrostatic discharge (ESD) can damage electronic components. Be sure that you are properly grounded
before beginning any hardware installation procedure.
Attention : If you disassemble your IBM High IOPS Adapter, you will void theDo Not Disassemble the Device
product warranty. Removing (and replacing) the bracket as instructed in this guide is considerednot
disassembly
These installation instructions are for any IBM IBM High IOPS Adapter.
Locate the serial number label(s) on your device and record the number(s) for future reference.
NOTE The serial number label(s) will have a number and a barcode.
NOTE : Once the ioMemory VSL software is installed, the device's serial number(s)Visible in fio-status
will be visible in the ioMemory VSL software utility.fio-status
Turn off the computer and disconnect the power cable.
Remove the computer's access panel. Locate an available PCIe slot compatible with the device. See Hardware
for PCIe slot requirements.Requirements
NOTE Consult your computer's documentation for details on removing the panel and identifying PCIe slots.
- 12 -
[no notes on this page]

IBM High IOPS Adapter Hardware Installation Guide for ioMemory VSL 3.2.2 |______ _ _ 13
4.
a.
b.
5.
6.
Remove the cover slot (if applicable).
Optional Half-height Bracket: If your product includes a half-height bracket (included with single
IBM High IOPS Adapter products), and you are installing the device in a low-profile system, replace the
full-height bracket before installing the device. Please refer to the sectionHalf-Height Bracket Installation
for details.
Power Cable: If your device includes a power cable (included with some products), you may install it
now.
Attention Additional power (through the cable) is required for newer products with multiple IBM High
IOPS Adapters.
For best results, plug in the power cable. See Power Cables for Second Generation IBM High IOPS Duo
for instructions and to see if the power cable is required for your device. For more informationAdapters
on using the PCIe slot to provide additional power, see .Hardware Requirements
Grasp the IBM High IOPS Adapter by the top edge and seat it gently but firmly in the available PCIe slot, for
example:
Attention This illustration is an example of one type of IBM High IOPS Adapter, your specific device will
install in the same manner.
Secure the IBM High IOPS Adapter's retaining bracket using a screw, lever, clasp, or other method (depending
on how your hardware is configured, consult your computer's documentation).
- 13 -
[no notes on this page]

IBM High IOPS Adapter Hardware Installation Guide for ioMemory VSL 3.2.2 |______ _ _ 14
7.
8.
9.
1.
2.
3.
Replace the computer's access panel.
Plug in the computer's power cable and turn on the computer.
Your operating system may detect the IBM High IOPS Adapter and ask if you want it to install a hardware
driver for the device. In that case, click .Cancel
NOTE : Note: We recommend saving the product box in case you need to store or return yourDevice Packaging
device. The ioMemory device product box is the safest way to store and transport your ioMemory device. It
is made of ESD-safe materials, and protects the device from damage in shipping.
To remove the IBM High IOPS Adapter, follow the above instructions in reverse. Be sure to place the
device in an ESD-safe package.
You are now ready to install the driver and utilities software. See the basedIBM High IOPS Hardware Installation Guide
on your operating system.
Half-Height Bracket Installation
For half-height installation (such as in low-profile systems), you need to replace the full-height retaining bracket with
the included half-height bracket.
Attention Electrostatic discharge (ESD) can damage electronic components. Be sure you are properly grounded
before starting any hardware installation procedure.
Locate the half-height bracket in your IBM High IOPS Adapter package:
Attention Use care in removing the retaining screws. Do not twist or pull on the bracket until both screws are
out as this can cause damage to the components.
To prevent damage to the IBM High IOPS Adapter, use only a Philips #1 tip screwdriver. Remove the two
screws holding the full-height bracket to the IBM High IOPS Adapter
Attention Take note of the position of the screws and how the bracket screw holes were inserted in the device.
You must insert the half-height bracket holes in the same manner.
Remove the bracket carefully from the device.
- 14 -
[no notes on this page]

IBM High IOPS Adapter Hardware Installation Guide for ioMemory VSL 3.2.2 |______ _ _ 15
4.
5.
Align the LEDs on the IBM High IOPS Adapter with the holes in the half-height bracket. Insert the bracket
screw holes in the same manner as the full height bracket was inserted. Refer to the example below that
matches your device configuration.
Attach the half-height bracket using a Philips #1 tip screwdriver to tighten the two screws.
Attention Do not over-tighten! This can cause damage to the device.
- 15 -
[no notes on this page]

IBM High IOPS Adapter Hardware Installation Guide for ioMemory VSL 3.2.2 |______ _ _ 16
6. Return to Step 3 of the installation section to complete the install.
Power Cables for Second Generation IBM High IOPS Duo Adapters
Some IBM High IOPS Adapters are compliant with the PCIe 2.0 bus specification of 25W and do not require external
power in compliant PCIe slots. Other devices require more than the 25W to function. Second Generation IBM High
IOPS Duo Adapters do require additional power through the provided power cable.
Installing the Cable
To use the external power cable, plug one end of the supplied cable into the product's power connection (circled
below, refer to the example that matches your device configuration), and the other into the auxiliary power source.
Additional power is on these devices. device will draw 55 watts from the 12V rail over the externalrequired The
cable. Make sure your system has sufficient power for the installed devices.
- 16 -
[no notes on this page]

IBM High IOPS Adapter Hardware Installation Guide for ioMemory VSL 3.2.2 |______ _ _ 17
IBM High IOPS Duo AdapterSecond Generation :
- 17 -
[no notes on this page]

IBM High IOPS Adapter Hardware Installation Guide for ioMemory VSL 3.2.2 |______ _ _ 18
Plug the product end of the cable (shown above) into the device. Plug the other end of the cable (shown below) into
an available power source cable. Consult your server documentation for available power options. Some servers may
require alternative power sources and adapters to connect with the cable.
NOTE There are two power cables supplied with the IBM High IOPS Duo Adapters, a 2x3 pin supporting one
Duo and a 2x4 pin supporting three Duos. These power cables mate directly to the corresponding aux
power connectors available in most IBM servers. However some IBM servers utilize a different aux power
connector, typically white in color, which is physically a 2x4 but will not accept the 2x4 cable supplied. For
these applications, the 2x3 pin cable is to be used. Care should be taken to insure that the 2x3 cable mates
properly with the 2x4 aux power connector. Due to the square and "D" shaped housing of the power cable
connector and corresponding holes in the aux power connector, they will only fit together one way.
Return to the installation instructions.
- 18 -
[no notes on this page]

IBM High IOPS Adapter Hardware Installation Guide for ioMemory VSL 3.2.2 |______ _ _ 19
IBM Support
IBM High IOPS Adapter software and documentation are available on the web at the following address:
http://www.ibm.com/support/entry/portal/docdisplay?lndocid=MIGR-65723 (follow that link and then select IBM High
).IOPS software matrix
IBM part number 00D2421
- 19 -
[no notes on this page]