ICC ICFOR444BK User manual

Rack Mount Fiber Optic Splice Enclosure
ICC’s Fiber Optic Rack Mount Enclosure comes with termination and splicing
capabilities. The unit has 4 RMS and has a slide-out master panel with four (4)
termination panel positions and a separate slide out splice tray storage unit.
The unit supports up to four (4) of ICC’s universal splice trays.
Fiber Optic Rack Enclosure
INSTALLATION INSTRUCTIONS
Structured Cabling Solutions
ASSEMBLY INSTRUCTIONS
CUSTOMER CARE / TECHNICAL SUPPORT • [email protected] / 888-275-4422 (ASK-4-ICC)
© Copyright 2008, ICC.ICC and ICC logo are registered trade name and trademark. All rights reserved. MSR-0413-2 REV A
Fiber Enclosure, 1 piece
A
Circuit Identification and Danger Label, 1 piece/ea.
B
Velcro® Tie Wraps, 4 pieces
C
Grounding Kit, 2 lugs, 2 screws and 2 nuts
D
Circuit Identification Hanger, 2 pieces
E
Lock Keys, 2 pieces
F
Fiber Slack Management Wraps, 4 pieces
G
Fiber Jumper Saddles, 14 pieces
H
Splice Tray Kit, 1 tray, 4 sleeves, and 4 tie wraps
I
Bracket Kit, 2 L-brackets and 12 screws
J
Tie Wraps, 8 pieces
K
ICFOR444BK
INCLUDES:
G
Step 1.
1. BRACKET INSTALLATION: The enclosure is designed for a standard front
3.0” rack mounting or 5.5” setback rack mounting or optional rear mounting.
Step 2.
2. SLIDE-OUT SHELF ASSEMBLY: The enclosure has two slide out shelves;
a master panel and a splice tray unit. Remove both trays from inside the
enclosure before installing any hardware.
C
D
B
L
A
Step 3.
3. Each tray is equipped with mounting holes for fiber management saddles,
slack management spools, grounding kit, and a splice tray stacker. Install all
hardware that will be utilized on both the master panel and splice tray panel.
Step 4.
4. NOTE: If a grounded chassis is required, install the grounding lug.
E
F
J
H
K
Includes a pair of
universal mounting
brackets that can be
adjusted to fit either
19” or 23” racks.
*All ICC racks are
19” only.
Option 1 Option 2
23” Mounting
19” Mounting
Termination Panel
Master Termination Panel
Mounting Holes
Mounting Holes
Splice Tray Stacker
Splice Tray Panel
Master Termination
Panel
Splice Tray Panel

Steps 5-to-8.
5. If a grounded chassis is required, install the grounding lug by inserting 1/4”
-20 pem stud into either the right hand or left hand side of the splice tray unit
in front of the grommets. Secure the grounding lug with a 1/4”-20 nut.
6. After installing the required hardware on the trays, slide the trays back into
the enclosure.
7. Mount the enclosure onto the rack and secure the enclosure with the
mounting bracket screws provided.
8. Install the Danger Label in a location that is visible to technicians.
11. FIBER CABLE INSTALLATION:
1. Pull the master termination panel out towards the rear of the enclosure
exposing the spools and previously installed termination panels.
2. Before installing fiber cable, follow approved cleaning procedures.
3. After cleaning, install one fiber cable at a time and route the
unjacketed/jacketed fibers around the spools and secure the fiber bundles as
required.
4. Provide a slack loop of fiber cable connecting the upper termination panel
slide-out tray to the bottom Splice Tray unit using tie wraps.
5. Route the cables or cable bundles around the slack storage spools and
into each of the fiber management saddles and then to the Splice Tray.
CAUTION: Ensure that slack allows the top or bottom tray to slide out without
damage to any cable.
Step 11.
Step 10.
10. Close the front panel and rotate both locks in a horizontal position.
Step 9.
9. Install the Circuit Identification label on the front door of the enclosure.
Use the label holders as an alignment guide.
12. Select the appropriate fiber splice sleeves from the kit supplied with the
splice tray and install into the splice tray.
Step 12.
13. Prepare a minimum of 4 ft. of fiber cable and route it around through the
splice tray. Splice all fiber required.
14. After splicing, slide the shelf back into position and secure all fiber cables
and bundles. Re-install both the front and rear doors of the enclosure.
Steps 13-to-14.
Pem Stud
Grounding Kit
(Option 1)
Grounding Kit
(Option 2)
Splice Tray Unit
Circuit
Identification
Hangers
Termination
Panel
Lexan Door
Circuit
Identification
Label
Enclosure
(Front View)
NOTE: Recommended cable length is 4 meters
Right handed sleeves shown.
Sleeves
Splice Tray