ICE COBOTICS ICE USA RS26+ User manual

ICE RS26+ / RS32+ 1
OPERATOR MANUAL
Operator & Parts Manual
Rider Auto Scrubber
RS26+
RS32+
8320040
REV.01 (07-2019)
www.ice4usa.com

2 ICE RS26+ / RS32+
OPERATOR MANUAL
HOW TO ORDER PARTS
Only use ICE Company supplied or equivalent parts. Parts and supplies may be ordered
online,by phone, by fax or by mail.
1. Identify the machine model.
2. Identify the machine serial number from the data label.
3. Ensure the proper serial number is used from the parts list.
4. Identify the part number and quantity.
Do not order by page or reference numbers.
5. Provide your name, company name, customer ID number,billing and shipping address,
phone number and purchase order number.
Please ll out at time of installation for future reference.
Model No.
Serial No.
Machine Options
Sales Rep.
Sales Rep. Phone No.
Customer ID Number
Installation Date
READ OPERATOR MANUAL CAREFULLY!
ICE Company Limited
XiangShi Road LiaoBu DongGuan GuangDong China
Tel: 0769 - 81869000
Fax:0769 - 81863000
Specications and parts are subject to change without notice.
IMPORTANT: To ensure full warranty protection, please ll out & return
your warranty card.
PROTECT THE ENVIRONMENT
Please dispose of packaging materials,old machine components
such as batteries, hazardous uids, including antifreeze and oil, in an
environmentally safe way according to local waste disposal regulations.
Always remember to recycle.

ICE RS26+ / RS32+ 3
OPERATOR MANUAL
SAFETY PRECAUTIONS......................................................................................................4
MACHINE COMPONENTS................................................................................................5-6
MACHINE SETUP & INSTALLATION....................................................................................7
MACHINE OPERATION........................................................................................................8
WHILE OPERATING MACHINE............................................................................................9
TANK DRAINING.................................................................................................................10
BATTERY CHARGING........................................................................................................10
PREVENTATIVE MAINTENANCE......................................................................................10
FAULT CODE AND ELIMINATE..........................................................................................11
TECHNICAL SPECIFICATIONS.........................................................................................13
PARTS LIST..................................................................................................14-41
WEAR AND TEAR PARTS..................................................................................................42
WIRING DIAGRAM .................................................................................................43
TABLE OF CONTENTS

4 ICE RS26+ / RS32+
OPERATOR MANUAL
SAFETY PRECAUTIONS
This machine is intended for commercial use. It
is designed exclusively to scrub hard oors in an
indoor environment and is not constructed for any
other use. Only use recommended accessories.
All operators shall read, understand and
exercise the following safety precautions:
1. Do not operate machine:
-Unless trained and authorized.
-Unless you have read and understand the
operators manual.
-In ammable or exploxive areas.
-With brake disabled.
-If not in proper operating condition.
2. Before starting machine:
-Make sure all safety devices are in place
and operate properly.
-Check brakes and steering for proper
operation.
3. When using machine:
-Go slow on inclines and slippery surfaces.
-Follow all safety guidelines.
-Be very careful when using the machine in
reverse.
-Reduce speed when turning.
-Report and x any damage to machine prior
to operating it.
-Never allow children to play on or
around.
4. Before leaving or servicing machine:
-Stop on level surface.
-Turn o󰀨 machine.
5. When servicing machine:
-Read operators manual thoroughly prior to
operating or servicing this machine.
-Use manufacturer supplied or approved
replacement parts.
-Secure machine with wheel blocks prior to
jacking the machine up.
-Use approved jack or hoist to safely elevate
the machine.
-Disconnect batteries prior to working on
machine.
-Avoid moving parts. Do not wear loose tting
clothing while servicing machine.
WARNING: Explosion or re can result
from hydrogen gas. Keep sparks and open
ames away! Keep battery compartment
open when charging.
WARNING: Flammable materials can
cause an explosion or re. Do not use
ammable materials in tanks.
WARNING: Flammable materials or
reactive metals can cause explosion or re.
Do not pick up.

ICE RS26+ / RS32+ 5
OPERATOR MANUAL
MACHINE COMPONENTS
1. Solution tank
2. Auto-ll hose port (Option)
3. Hose ll port & Cap
4. Squeegee assembly
5. Wheels, 10 inch
6. Scrub head assembly
7. Side squeegee assembly
8. Cup holder
9. Brake pedal
10. Propel pedal
11. Front drive wheel
12. Operator seat
13. Steering wheel
14. Key Switch
15. Control panel, Touch screen
16. LED light, work
17. Emergency Stop button
18. Adjusting handle, seat
19. O󰀨-board battery
charger port (Option)
20. Watching window, On board
battery charger
21. Warning light
22. Recovery tank cover
23. Recovery tank
24. USB Charging port
25. Cabin door, Detergent bottle
compartment
26. Mesh, Battery charger
power cord.

6 ICE RS26+ / RS32+
OPERATOR MANUAL
MACHINE COMPONENTS
27. Horn button
28. Battery meter
29. Date & Time
30. Solution ow adjusting button
31. 1-Step starting button
32. Work mode select button
33. Detergent adjusting button
34. Timer
35. Brush pressure adjusting button
36. Direction button
37. Setting button
38. Vacuum motor button
39. Fault icon
40. Warning light button
41. Drain hose, recovery tank
42. Vacuum hose
43. Drain hose, solution tank
44. Adjusting knob, Squeegee

ICE RS26+ / RS32+ 7
OPERATOR MANUAL
UNCRATING MACHINE
Be sure and check packing carton for any damage.
Immediately report any damage to carrier. Check
the contents of package to ensure that the
following items are included:
• Machine
• 4-6V Batteries
• Squeegee assembly
• 2-Pad drivers
• 2-Brushes
1. Uncrate the wooden box, place the top board
on the edge of pallet, lie in the front of the
machine, as below shown.
WARNING: Do not operate machine unless
you have read & understood this manual.
2. Install batteries.(see INSTALLING BATTERIES)
3. Turn on the Key Switch (Machine components,
#14) , make sure the Squeegee assembly
(Machine components, #4) and the Scrub head
assembly (Machine components, #6) is o󰀨 the
oor.
4. Sit in the Operator seat (Machine components,
#12), hold the Steering wheel (Machine
components, #13), press the Propel pedal
(Machine components, #10) and driving slowly
the machine down from the slope.
INSTALLING BATTERIES
WARNING: Batteries emit hydrogen gas.
Explosion or re can result from hydrogen
gas.Keep sparks and open ames away! Keep
battery compartment open when charging.
Recommended battery spec:
4-6V, 260AH@20HR deep cycle batteries.
Max. batteries dimensions :
300mm (L) X 180mm (W) X 290mm (H)
1. Turn the Key switch o󰀨.
2. Open and prop up the Operator seat, place the
batteries into the battery compartment carefully.
NOTE: Do not drop the batteries into the
compartment.
3. Connect battery cables to posts in numbered
order as shown in drawing below.
NOTE: RED to POSITIVE AND BLACK to
NEGATIVE.
4. Reinstall the Operator seat and the Battery box.
MACHINE SET UP
INSTALLING BRUSHES OR PADS
1. Turn o󰀨 the 1-Step staring button (Machine
components, #31) and raise the Scrub head
assembly o󰀨 the oor, then stop machine on the
level surface, ensure the machine is turned o󰀨.
2. If using the pad driver, rst attach the
appropriate pad to the pad driver surface.
3. Align the pad driver or brush under the motor
hub and push it upward to engage.
4. To remove the pad driver or brush, raise the
scrub head and remove the Side squeegee
assembly (Machine components, #7), push the
edge of brush downward.
MACHINE SET UP & INSTALLATION

8 ICE RS26+ / RS32+
OPERATOR MANUAL
MOUNTING THE SQUEEGEE ASSEMBLY
1. Turn o󰀨 the 1-Step switch and raise the
Squeegee assembly o󰀨 the oor.
2. Mount the squeegee assembly to the squeegee
pivot bracket. make sure the knobs are
completely seated into the slots before securing
knobs.
3. Connect the Vacuum hose (Machine
components, #42) to the squeegee assembly.
Loop the hose by using the hose clip provided.
4. Check the squeegee blades for proper
adjustment by adjusting the Squeegee adjusting
knob (Machine components, #44).
FILLING THE SOLUTION TANK
The machine is equipped with a Hose ll port
(Machine components, #3)at the side of the
machine, and a bucket ll-port located under the
recovery tank.
NOTE: Before accessing the bucket ll-port
make sure that the recovery tank is empty.
When lling the solution tank with a bucket,
make sure that the bucket is clean. Do not use
the same bucket for lling and draining the
machine.
AUTO-FILL HOSE PORT(OPTION)
The machine have a optional Auto-ll hose port
(Machine components, #2), you can ll the Solution
tank by using lling hose equipped with Quick
connectors.
1. Connect the Quick connector of the lling hose
to the Auto-ll port and connect the another end
to the water supply connector.
2. Turn the water supply on, the water ow will
automatically shut o󰀨 when solution tank is full,
and then turn the water supply o󰀨.
3. Disconnect the Quick connector from the water
supply end rst, and then disconnect the Filling
hose from machineand store in proper location.
WARNING: Do not put any ammable
materials into solution tank. this can cause an
explosion or a re.
FILLING THE DETERGENT BOTTLE
The machine is equipped with a 4 liters Detergent
bottle under the Recovery tank. You can ll the
Detergent bottle by openning the Deterent bottle
cabin door (Machine components, #25), and
removing the detergent bottle cap.
The ratio of water and detergent is 0~5%, you
can adjust this ratio via pressing the Detergent
adjusting button (Machine components, #33).
NOTE: Only use recommended cleaning
chemicals. Contact your janitorial supply
distributor for recommendations on
properchemicals.
WARNING: Do not operate machine
unless you have read and understand this
manual.
PRE-OPERATION CHECKS
1. Check the tank cover seals for damage.
2. Drain the recovery tank, check the vacuum fan
inlet lter, clean them if necessary.
3. Check the vacuum hose for debris or blockage.
4. Check the squeegees for damage, wear and for
deection adjustment.
5. Check whether Pad/Brush is installed properly .
6. Check the brakes and steering for proper
operation.
OPERATION THE MACHINE
1. Sit on the Operator seat, adjusting the seat
to comfortable place by pushing the Seat
adjustment handle (Machine components, #18).
NOTE: The machine will not travel unless the
operator is sitting in the operator seat.
2. Turn on the machine.
Check the Touch screen (machine components,
#15) , if the machine have fault there will have
a Fault icon display and blinking (Machine
components, #39), please Do Not operation the
machine unless the faults have been eliminated
(please see FAULT CODES AND ELIMINATE
section).
3. Select the proper working mode by pressing
the Work mode select button (Machine
components, #32). The machine have 3 Modes
of ECO, HEAVY Duty and User custom.
NOTE: To energy saving, recommend to
using the ECO mode as possible.
For the User custom mode, you can select
the preferred settings by pressing the Solution
ow adjusting button (Machine components,
#30), Detergent adjusting button (Machine
components, #33), and the Brush pressure
MACHINE OPERATION

ICE RS26+ / RS32+ 9
OPERATOR MANUAL
adjusting button (Machine components, #35).
4. Turn on the 1-Step starting button, the Scrub
head assembly and the Squeegee assembly
will lower down automatically, all the presetting
functions will turn on.
5. The machine can scrub in both forward and
backward, press the Directional button (Machine
components, #36) to select the direction.
The horn will sound and the squeegee will
raise automatically (the vacuum motor will turn
o󰀨 after a short delay) when drive machine
backwards. This is to prevents damaging the
squeegee.
NOTE: Go slow when drive machine
backwards.
6. Press the Propel pedal, the machine start
scrubbing, the speed can be adjusted by
controlling the force of foot stepping, light is
slow, heavy is fast.
NOTE: Go slow on inclines and slippery
surfaces.
7. To stop scrubbing, turn o󰀨 the 1-Step starting
button, the scrub head will raise automatically,
the squeegee will also raise after a short delay,
please keep moving until the dirty water is
picked up, and then release the propel pedal
and stop scrubbing.
8. Turn o󰀨 the machine.
BRAKE DEVICE
The machine is drived by the Front drive wheel
(Machine components, #11), that is equipped with
a brake device. When you release the Propel
pedal, the machine will stop travel, the park brake
will engage after a short delay.
The machine is equipped with a Brake pedal
(Machine components, #9), that can be used to
control the machine if quicker stopping is needed
or if operating on an incline.
EMERGENCY STOP BUTTON
The machine is equipped with an Emergency stop
button (Machine components, #17), please push
it if any emergency, that will shut o󰀨 all power of
machine and brake immediately.
To restart the machine, please reset the
Emergency stop button, and turn o󰀨 the machine
and then restart.
NOTE: Please hold the steering wheel when
emergency stop.
WARNING: Fire Or Explosion Hazard. Do
Not Pick Up Flammable Materials Or Reactive
Metals.
1. Go slow on inclines and slippery surfaces, go
slow when turn and reverse. Do not operate the
machine on inclines that exceed 7% (4°).
2. Drive machine in a straight path as possible,
avoid turning the Steering wheel too sharply
when machine is in motion. avoid sudden turns
except emergencies.
3. Do not keep the machine in the same position
with pad / brush spinning, keep the machine
moving to prevent damage to oor nish.
4. If the squeegee assembly leaves streaks on the
oor, raise the squeegee o󰀨 the oor and wipe
the blades down with a damp cloth. Pre-sweep
the area to prevent leaving streaks on the oor.
5. To obtain the optimum cleaning performance,
you can adjust the brush pressure, solution
ow and detergent dosage as your required. If
poor picking up water performance is observed,
please stop scrubbing and check the squeegee
blade, adjust or replace if necessary.
6. If the dirty water path exceed the width of
squeegee, please adjust the side squeegee
assembly.
7. Pour a recommended defoamer into the
recovery tank if excessive foam appears.
WARNING: The foam do not activate
water level switch, excessive foam may result
in vacuum motor damage.
8. Press the Horn button (Machine components,
#27) to alert if necessary.
9. The machine is equipped with a Warning light
(Machine components, #21), you can select turn
ON or OFF by the Warning light button (Machine
components, #40).
10. If there have Fault icon display and blinking
on the touch screen, please stop using the
machine and to eliminate the fault (Please see
FAULT CODESAND ELIMINATE section).
11. For heavily soiled areas, please use HEAVY
DUTY SCRUBBING mode by work mode select
button.
12. If you only want to pick up water needn't
scrubbing, Turn on the Vacuum motor
button(Machine components, #38) , the
squeegee will lower down, and turn o󰀨 the
1-Step starting button (if it is ON), the scrub
head will raise and then start to picking water
up.
WHILE OPERATING MACHINE

10 ICE RS26+ / RS32+
OPERATOR MANUAL
DRAINING THE RECOVERY TANK
Any time scrubbing is completed, or when relling
solution tank, the recovery tank should be drained
and cleaned.
WARNING: If the recovery tank is not
drained when the solution tank has been
relled, foam or water may enter the oat shut-
o󰀨 screen and cause damage to the vacuum
motor.
1. While holding the Recovery tank drain hose
(Machine components, #41) upward, remove
the cap and lower hose to drain.
2. Open the Recovery tank cover (Machine
components, #22) and rinse out the tank. Use
a rag to remove any excess dirt.
3. Remove and clean the vacuum fan inlet lter
located in the recovery tank. Clean the lter with
a damp cloth or low pressure water hose if dirty.
Allow the vacuum fan lter to dry completely
before reinstalling it in the machine.
DRAINING THE SOLUTION TANK
Any time scrubbing operation is completed, the
solution tank should be drained and cleaned.
1. While holding the Solution tank drain hose
(Machine components, #43) upward, remove
the cap and lower hose to drain.
2. Rinse the solution tank with clean water after
every use. This will help prevent chemical
buildup and clogging of the solution lines.
WARNING: Fire Or Explosion Hazard.
Batteries Emit Hydrogen Gas. Keep Sparks and
Open Flame Away. Keep Battery Compartment
Propped Open When Charging.
Use only apprved chargers with the following
specications:
• Automatic shut o󰀨 circuit
• Deep cycle charging
• Output current of 20-30 Amps
• Output voltage of 24 volts
ON-BOARD BATTERY CHARGER
As standard conguration, the machine is equiped
with the On-board battery charger. The settings
of On-board battery charger had been set for the
recommended batteries type.
WARNING: The On-board battery
charger setting's change are to be completed
by authorized service centers only. Failure
to properly set will result in the batteries or
charger damage.
1. Transport the machine to a well ventilated area.
2. Turn the machine o󰀨.
3. If charging wet (lead acid) batteries check the
uid level before charging.
4. Prop up the Operator seat by the support stand
for ventilation.
5. Connect the charger's AC power supply cord to
a properly grounded receptable.
6. The charger will automatically begin to charge,
you can watching the charging status on the
window (Machine components, #20), once the
charging cycle begins, the indicator lights will
progress from red, yellow to green. when the
green indicator light comes on, the charging
cycle is done. Unplug the charger cord.
NOTE: The machine will can not operate
when charging.
WARNING: Before performing any
maintenance on the machine, be sure that
the power is turned o󰀨, or the batteries are
disconnected!
WARING: Repairs are to be completed by
Authorized service centers only. Any repairs
completed by unauthorized persons will avoid
the warrenty.
DAILY MAINTENANCE
1. Remove pad driver/ brush and clean with
approved cleaner.
2. Drain recovery and solution tanks completely
and rinse out with clean water. Visually check
the recovery tank for debris and clean out as
necessary.
BATTERY CHARGING
TANK DRAINING
PREVENTATIVE MAINTENANCE

ICE RS26+ / RS32+ 11
OPERATOR MANUAL
3. Raise the squeegee assembly o󰀨 oor and wipe
it down with a damp towel. Be sure to store the
squeegee in the up position.
4. Remove the vacuum fan inlet lter and rinse it
out with clean water.
5. Clean machine with an approved cleaner and a
damp towel.
6. Recharge the batteries.
7. Check the condition of the squeegee blade
wiping edge, rotate blade if worn.
MONTHLY MAINTENANCE
1. Clean the battery tops to prevent corrosion.
2. Check for loose battery cable connections.
3. Inspect and clean the recovery tank cover seal.
Replace it if damaged.
4. Lubricate all grease points and pivot points with
silicon spray and approved grease.
5. Check the machine for loose nuts and bolts.
6. Check the machine for leaks.
BATTERY MAINTENANCE
WARNING: Batteries emit hydrogen gas
and an explosion o re can result. Keep sparks
and re away from batteries at all times.
WARNING: Whenever servicing batteries,
be sure to wear protective gloves. Avoid
contact with battery acid at all times.
NOTE: For the best machine performance, keep
batteries charged at all times. Do not let them
sit in a discharged condition.
1. Always follow the battery charging directions as
outlined in the BATTERY CHARGING section of
this manual.
2. Keep battery tops and terminals free from
corrosion. A strong solution of baking soda
and water is the best way to keep the batteries
corrosion free. DO NOTALLOW THE BAKING
SODA / WATER SOLUTION TO ENTER THE
BATTERY CELLS.
3. Use a wire brush with the baking soda solution
to properly clean the battery posts and
connections.
4. Check battery connections for wear and loose
terminals. replace if necessary.
MACHINE STORAGE
1. Always store the machine indoors.
2. Always store the machine in a dry area.
3. Always store the machine in its upright position.
4. Always store the machine with the pad driver/
brush raised o󰀨 the oor.
5. Always store the machine with the squeegee
assembly raised o󰀨 the oor.
6. If storing in an area which may reach freezing
temperatures, be sure to drain all uids from the
machine prior to storage. Any damage caused
by freezing temperatures will not be covered by
the warranty.
7. Drain the recovery tank.
8. Drain the solution tank of all uid.
FAULT CODE & SOLUTION
The machine equipped with a 7-inch touch screen
(Machine components, # 15), the touch screen will
display Battery meter (Machine components, #28),
Date and Time (Machine components, #29), and
Working accumulated hours (Machine components,
#34).
When the machine detects a fault, there will have
a Fault icon blinking (Machine components, #39)
on the touch screen accompany an audible alarm
Occasionally.
The Fault icon have 2 colors. Yellow icon
represents a low level fault, you can click it to pop
up a fault message window, it will guide you how to
eliminate the fault.
Red icon represents a serious fault, the fault
message window will pop up automatiaclly, you can
not close it unless the fault be eliminated.
Once the fault icon occuring, please DO NOT
continue operate machine unless the faults are
eliminated.
Turn o󰀨 the machine, then to solve the fault, the
fault icon will be eliminated when machine restart.
If the fault icon is occurred frequently, or can't be
eliminated, please contact ICE service center.
Please refer to the below table to determine the
fault cause and the solution.

12 ICE RS26+ / RS32+
OPERATOR MANUAL
FAULT
CODE FAULT MESSAGE SOLUTION
F01 Seat Empty Sit in seat
F02 Squeegee or Scrub head Actuator Overload Check Squeegee or Scrub head Actuator
F04 Vacuum Motor Overload Check Vacuum Motor
F05 Brush Motor (Left) Overload Check Brush Motor (Left)
F06 Brush Motor (Right) Overload Check Brush Motor (Right)
F07 Drive Motor Overload Check Drive Motor
F08 Recovery Tank Full Drain Recovery tank
F09 Solution Tank Empty Rell Solution tank
F10 Battery Low Charge battery
F11 Battery Discharged Charge battery Immediately
F12 Brake Open Circuit Check brake wiring
F13 Release Accelerate Pedal Release the propel pedal
F14 Brake Short Circuit Check brake wiring
F16 Main Controller Overheat Turn o󰀨 the machine and re-start after a while
F18 Accelerator Sensor Open Circuit Check accelerator sensor
F19 Brake Sensor Open Circuit Check Brake sensor
F20 Brush Motor (Left) Open Circuit Check Brush Motor (Left) Wiring and Connector
F21 Vacuum motor Open Circuit Check Vacuum motor Wiring and Connector
F22 Solenoid Valve Short Circuit Check Solenoid valve Wiring and Connector
F23 Solenoid Valve Open Circuit Check Solenoid valve Wiring and Connector
F24 Drive Motor Open Circuit Check Drive motor wiring and Connector
F25 Brush Motor (Right) Open Circuit Check Brush Motor (Right) Wiring and Connector
F43 Emergency Stop Release Emergency stop button
F49 Main Controller Fault Replace Main controller
F50 Main Controller Fault Replace Main controller
F53 Detergent Pump Short Circuit Check Detergent pump Wiring and Connector
F54 Detergent Pump Open Circuit Check Detergent pump Wiring and Connector
F55 Scrub Head Actuator Open Circuit Check Scrub head actuator Wiring and Connector
F56 Squeegee Actuator Open Circuit Check Squeegee actuator Wiring and Connector
F57 Flashing Light Short Circuit Check Flashing light Wiring and Connector
F58 Flashing Light Open Circuit Check Flashing light Wiring and Connector
F61 Main Relay (#1) Short Circuit Check Main Relay (#1) Wiring and Connector
F62 Main Relay (#1) Open Circuit Check Main Relay (#1) Wiring and Connector
F63 Main Relay (#2) Short Circuit Check Main Relay (#2) Wiring and Connector
F64 Main Relay (#2) Open Circuit Check Main Relay (#2) Wiring and Connector
F65 Drive Motor Short Circuit Check Drive Motor Wiring and Connector
F67 Brush Motor (Left) Short Circuit Check Brush Motor (Left) Wiring and Connector
F68 Brush Motor (Right) Short Circuit Check Brush Motor (Right) Wiring and Connector
F69 Vacuum Motor Short Circuit Check Vacuum Motor Wiring and Connector
F70 Scrub Head Actuator Short Circuit Check Scrub head actuator Wiring and Connector
F71 Squeegee Actuator Short Circuit Check Squeegee actuator Wiring and Connector
FAULT CODE & SOLUTION

ICE RS26+ / RS32+ 13
OPERATOR MANUAL
TECHNICAL SPECIFICATIONS
MODELMODEL RS26+ RS32+
LENGTHLENGTH 63.4 in / 1,610 mm
WIDTH (MACHINE WITHWIDTH (MACHINE WITH
SCRUB HEAD)SCRUB HEAD) 33 in / 838 mm 36.5 in / 927 mm
HEIGHTHEIGHT 56.7 in / 1,440 mm
WEIGHTWEIGHT 618 lbs / 280 Kg 640 lbs / 290 Kg
WEIGHT WITH BATTERIESWEIGHT WITH BATTERIES 880 lbs / 400 Kg 900 lbs / 410 Kg
RECOVERY TANK CAPACITYRECOVERY TANK CAPACITY 27.7 Gal / 105 L
SOLUTION TANK CAPACITYSOLUTION TANK CAPACITY 28.5 Gal / 108 L
SQUEEGEE WIDTHSQUEEGEE WIDTH 33.8 in / 860 mm 40 in / 1,030 mm
CLEANING PATH WIDTHCLEANING PATH WIDTH 26 in / 650 mm 32 in / 810 mm
PRODUCTIVITY RATE PERPRODUCTIVITY RATE PER
HOUR (IN THEORY)HOUR (IN THEORY) 46, 300 ft2
4,300 m255, 600 ft2 5,200 m2
TRAVEL SPEEDTRAVEL SPEED
(TRANSPORT)(TRANSPORT) 4 Mile / h
6.5 Km / h
MINIMUM AISLE TURNMINIMUM AISLE TURN 71 in / 1,800 mm 75 in / 1,900 mm
PAD/BRUSH PRESSUREPAD/BRUSH PRESSURE 80 lbs / 35 Kg 120 lbs / 55 Kg
160 lbs / 75 Kg
SOLUTION FLOWSOLUTION FLOW 0 ~ 0.7 Gal / Min
0 ~ 2.7 L / Min
BATTERIES 4 x 6V, 240AH@ 20Hr
VOLTAGEVOLTAGE 24V DC
DRIVE WHEELDRIVE WHEEL 1.1 hp / 0.8 KW
BRUSH MOTORBRUSH MOTOR (2) 0.6 hp / 0.45 KW, 210 RPM
VACUUM MOTORVACUUM MOTOR 0.6 hp / 0.45KW
VACUUM WATER LIFT (MAX)VACUUM WATER LIFT (MAX) 70 in. H2O / 1780 mm. H2O
RUN TIME PER CHARGERUN TIME PER CHARGE 3~3.5 Hours
DECIBEL RATING ATDECIBEL RATING AT
OPERATOR'S EAR, INDOORSOPERATOR'S EAR, INDOORS 68 dB(A)
GRADE LEVEL, MAXGRADE LEVEL, MAX Scrubbing: 4°/7% Transporting (empty):10°/17.5%

14 ICE RS26+ / RS32+
OPERATOR MANUAL
MAIN FRAME GROUP

ICE RS26+ / RS32+ 15
OPERATOR MANUAL
MAIN FRAME GROUP
DIA
NO. PART NUMBER DESCRIPTION NO REQ'D
1 8320150 MAIN FRAME, WELDED 1
2 8310133 RUBBER GROMMET 4
3
8310119 10" WHEEL, PU TIRE 2
1612605 BALL BEARING,6205-2RS 4
8315250 10" WHEEL, ANTI-SLIP, OPTION 2
4 1436025 RETAINING RING, 25MM 2
5 8310150 WHEEL CAP 2
6 1521410 SCREW, SOCKET, M4×10 2
7 1883207 BARRIER TERMINAL BLOCK 1
8 8310120 BRACKET, STAND 2
9 1421824 FLAT WASHER, M8×∮24×2.0 3
10 1422821 LOCK WASHER M8 3
11 1021825 BOLT, HEX, M8×25 3
12 8210118 STATIC STRAP 1
13 8310708A HORN, 24VDC, KIT 1
14 1421307 FLAT WASHER, M3×∮7×0.5 4
15 1221312 SCREW, PAN HEAD, M3×12 2

16 ICE RS26+ / RS32+
OPERATOR MANUAL
STEERING & DRIVE WHEEL GROUP

ICE RS26+ / RS32+ 17
OPERATOR MANUAL
STEERING & DRIVE WHEEL GROUP
DIA
NO. PART NUMBER DESCRIPTION NO REQ'D
1 8313704 DECAL, TOUCH SCREEN PANEL 1
2 8313703 COVER, TOUCH SCREEN 1
3 8313723 FPC CONNECTOR 1
4 1311006 SELF-TAPPING CREW, ST3.0×6.0 2
5 8313712B TOUCH SCREEN, ENGLISH UI 1
6 1221306 SCREW, M3×6 4
7 8313702 BASE, TOUCH SCREEN 1
8 1221516 SCREW, M5×16 4
9 8313701 TUBE WITH FLANGE 1
10 1421515 FLAT WASHER, M5×∮15×1.0 4
11 1422513 LOCK WASHER, M5 4
12 1221512 SCREW, PAN HEAD, M5×12 6
13 8313612 HEX NUT, M24 1
14 8313610 STEERING WHEEL 1
15 1021830 BOLT, HEX HEAD,M8×30 4
16 1422821 LOCK WASHER, M8 12
17 1421816 FLAT WASHER, M8×∮16×1.6 4
18 1021035 BOLT, HEX HEAD,M10×35 6
19 1422026 LOCK WASHER, M10 10
20 1421020 FLAT WASHER, M10×∮20×2 6
21 8313609 FLANGE BEARING, PLASTIC 1
22 8313608 FLANGE BAEARING 3
23 8313601 STEERING SUPPORT 1
24 1021820 BOLT, HEX HEAD,M8×20 8
25 1421824 FLAT WASHER, M8×∮24×2.0 8
26 8310640 ACCELERATOR & BRAKE ASSEMBLY 1
27 8310431 HALL SENSOR WITH CABLE 1
28 1021050 BOLT, HEX HEAD,M10×50 4
29 1421030 FLAT WASHER, M10×∮30×2.5 4
30 8320685 STEER-CONTROLASSEMBLY 1

18 ICE RS26+ / RS32+
OPERATOR MANUAL
DIA
NO. PART NUMBER DESCRIPTION NO REQ'D
31 8310687 BRACKET, WIRING 1
32 8310680 DRIVE WHEEL, 24VDC 1
33 1513020 SCREW, HEX SOCKET, M10×20 4
34 8310645 BRACKET, FLANGE BEARING 1
35 8310609 BEARING, FLANGE 1
36 1534508 SET SCREW, M5 ×8 8
37 8310604 U-JOINT 1
38 1654025 KEY, 4.75×4.75×25.4 2
39 8313621 SHAFT, STEERING 1
40 1531830
HEX SOCKET CAPHEAD SCREW , M8×30
41 8313620 U-JOINT 1
42 8313602 BRACKET, FLANGLE BEARING 1
43 8313607 BELT 1
44 8313606 PULLEY 2
45 1655025 KEY, 5×5×25 3
46 8313611 BUSHING 2
47 8313622 SHAFT, PULLEY 1
48 8313605 SHAFT , PULLEY 1
49 1436025 RETAINING RING, 25MM 3
STEERING & DRIVE WHEEL GROUP

ICE RS26+ / RS32+ 19
OPERATOR MANUAL
SOLUTION TANK GROUP

20 ICE RS26+ / RS32+
OPERATOR MANUAL
SOLUTION TANK GROUP
DIA
NO. PART NUMBER DESCRIPTION NO
REQ'D
1 8310132 NON-SLIT MAT 2
2 1222508 SCREW, M5×8 8
3 1512820 SCREW, HEX SOCKET M8×20 4
4 1421824 FLAT WASHER, M8×∮24×2.0 13
5 8320102 FOOTREST PLATE 1
6 8310140 JUNCTION PLATE 4
7 8320101 SOLUTION TANK 1
8 1422821 SPRING LOCK WASHER, M8 8
9 1021820 BOLT, HEX HEAD, M8×20 8
10 8310130 BRACKET, SOLUTION TANK MNTG 3
11 8310124 ELBOW, G1/2 1
12 8310142 NUT, M36 1
13 8310141 SEALING 2
14 1221512 SCREW, PAN HEAD, M5×12 9
15 1422513 LOCK WASHER, M5 4
16 1421510 FLAT WASHER, M5×∮10×1.0 9
17 8311310C SOLENOID VALVE 1
18 1021616 BOLT, HEX HEAD, M6×16 2
19 1422616 LOCK WASHER M6 2
20 1421612 FLAT WASHER, M6×∮12×1.6 2
21 8320105 BRACKET 1
22 8320128 BRACKET, PROTECTIVE 1
23 8310238A SENSOR, SOLUTION LEVEL, KIT 1
24 8310125 CAP, SOLUTION TANK 1
25 8320123 QUICK CONNECTOR G1/2 1
26 8320127 GASKET 1
27 1021825 BOLT, HEX HEAD, M8×25 1
28 8310225 SLEEVE, ∮8.1×∮12.7×7.8 1
29 8320104 ARM, RECOVERY TANK SUPPORT 1
30 1962050 CLAMP, 2 INCH 1
31 8011040 DRAIN HOSE 1
32 8320121 FLOAT VALVE 1
33 8320122 ELBOW, G1/2 1
34 8310123 ADAPTER, STRAINER ASSEMBLY 1
35 8310122 STRAINER 1
36 8310463 CAPADAPTER 1
37 8310464 INSERT TUBE 1
38 8310462 CAP, BOTTLE 1
39 8320901 DETERGENT TANK 1
40 8113009 CLAMP, NYLON 5