ICE COBOTICS ICE USA i15B Programming manual

Operator & Parts Manual
Automatic Scrubber
www.ice4usa.com
i15B
INTELLIGENT CLEANING EQUIPMENT
8401902
REV.01 (05-2021)

2ICE i15B
OPERATOR MANUAL
HOW TO ORDER PARTS
Only use ICE Company supplied or equivalent parts. Parts and supplies may be ordered
online,by phone, by fax or by mail.
1. Identify the machine model.
2. Identify the machine serial number from the data label.
3. Ensure the proper serial number is used from the parts list.
4. Identify the part number and quantity.
Do not order by page or reference numbers.
5. Provide your name, company name, customer ID number,billing and shipping address,
phone number and purchase order number.
Please ll out at time of installation for future reference.
Model No.
Serial No.
Machine Options
Sales Rep.
Sales Rep. Phone No.
Customer ID Number
Installation Date
READ OPERATOR MANUAL CAREFULLY!
ICE Company Limited
XiangShi Road LiaoBu DongGuan GuangDong China
Tel: 0769 - 81869000
Fax:0769 - 81863000
Specifications and parts are subject to change without notice.
IMPORTANT: To ensure full warranty protection, please ll out & return
your warranty card.
PROTECT THE ENVIRONMENT
Please dispose of packaging materials,old machine components
such as batteries, hazardous uids, including antifreeze and oil, in an
environmentally safe way according to local waste disposal regulations.
Always remember to recycle.

ICE i15B 3
OPERATOR MANUAL
SAFETY PRECAUTIONS......................................................................................................4
MACHINE COMPONENTS...................................................................................................5
MACHINE OPERATION .......................................................................................................6
MACHINE SETUP & INSTALLATION.............................................................................6
WHILE OPERATING MACHINE....................................................................................7
TANK DRAINING.....................................................................................................8
BATTERY CHARGING..........................................................................................8
PREVENTATIVE MAINTENANCE.......................................................................................9
BASIC TROUBLESHOOTING.............................................................................................10
TECHNICAL SPECIFICATIONS......................................................................................11
PARTS LIST................................................................................................12-25
WEARABLE PARTS............................................................................................26
WIRING DIAGRAM....................................................................................27
TABLE OF CONTENTS

4ICE i15B
OPERATOR MANUAL
SAFETY PRECAUTIONS
This machine is intended for commercial use. It
is designed exclusively to scrub hard oors in an
indoor environment and is not constructed for any
other use. Only use recommended accessories.
All operators shall read, understand and
exercise the following safety precautions:
1. Do not operate machine:
-Unless trained and authorized.
-Unless you have read and understand the
operators manual.
-In ammable or explosive areas.
-If not in proper operating condition.
-In outdoors areas.
2. Before starting machine:
-Make sure all safety devices are in place
and operate properly.
3. When using machine:
-Go slow on inclines and slippery
surfaces.
-Follow all safety guidelines.
-Be very careful when using the machine in
reverse.
-Reduce speed when turning.
-Report and x any damage to machine prior
to operating it.
-Never allow children to play on or
around.
-Do not operate on inclines that exceed 5%
(3°).
4. Before leaving or servicing machine:
-Stop on level surface.
-Turn o󰀨 machine.
5. When servicing machine:
-Read operators manual thoroughly prior to
operating or servicing this machine.
-Use manufacturer supplied or approved
replacement parts.
-Secure machine with wheel blocks prior to
jacking the machine up.
-Use approved jack or hoist to safely elevate
the machine.
-Disconnect batteries prior to working on
machine.
-Avoid moving parts. Do not wear loose tting
clothing while servicing machine.
WARNING: Fire or Explosion Hazard.
Keep sparks and open ames away! Keep
battery compartment open when charging.
WARNING: Flammable materials can
cause an explosion or re. Do not use
ammable materials in tanks.
WARNING: Flammable materials or
reactive metals can cause explosion or re.
Do not pick up.

ICE i15B 5
OPERATOR MANUAL
MACHINE COMPONENTS
1. Safety Lock-Out Switch
2. Control Handle
3. Trigger
4. Squeegee Vacuum Hose
5. Recovery Tank Cover
6. ICE Logo
7. Recovery Tank
8. Bucket Fill Port/ Clean-Out Port
9. Solution Tank
10. Scrub head
11. Bumper Rollers
12. Caster,1.5Inch,Squeegee Blade Adjustment
13. 10 Inch wheels
14. Recovery Tank Drain Hose
15. Squeegee Lift Lever
16. Leveling Rod
17. Main Power ON/OFF Switch
18. Battery Discharge Indicator
19. Vacuum Power ON/OFF Switch
20. Clear Cover,Battery Charger
21. Connector, On-Board Battery Charger
22. Clean Water Tank Drain Cover
23. Ball Valve
24. Battery
25. Vacuum Motor, 24VDC
26. Brush Motor, 24VDC
27. Solenoid, 24VDC
28. Squeegee Assembly
29. Filter Assembly
1 2 3 4
5
7
8
13
9
10
15
14
3
17
18
19
20
21
23
25
22
26
6
16
1112
2
24
27
29
28

6ICE i15B
OPERATOR MANUAL
FOR SAFETY: Do not operate machine unless
operator manual is read and understood.
PRE-OPERATION
1. IMPORTANT: To prevent vacuum system from
clogging, sweep and dust-mop oor.
2. Make sure battery is charged.
3.Check that the brush and squeegee blades are
installed.
SCRUBBING FLOORS
FOR SAFETY: Before Operating machine,follow
safety guidelines concerning wet oors.
WARNING: Fire or Explosion Hazard, Do
Not Use or Pick Up Flammable Materials.
WARNING: Spinning Brush. Keep Hands
Away.
1. Pull the handle adjustment lever and adjust
the handle to a comfortable operating height.
Release the lever to lock the position.
2. Press the main power switch to the on ( I )
position.
3. Press the vacuum switch to the on ( I ) position.
4. To begin scrubbing,rst press the safety switch
(1),pull the start triggers(2) and push or pull the
machine in either direction .
5. For heavily soiled areas, use the double scrub
method. First scrub the soiled area with the
vacuum switch turned o󰀨 then scrub the area a
second time with vacuum switch turned on.
UNCRATING MACHINE
Be sure and check packing carton for any damage.
Immediately report any damage to carrier. Check
the contents of package to ensure that the
following items are included:
• Machine
• 2-12V Batteries
• Squeegee assembly
• Battery Charger
• Pad Driver
• Brush
INSTALLING BATTERIES
The batteries are already in the machine upon
delivery; However you will need to connect the
cables to the battery posts.
WARNING: Fire or Explosion Hazard.
Keep sparks and open ames away! Keep
battery compartment open when charging.
1. Turn o󰀨 the machine.
2. Lift the Recovery tank (see machine
components, p5 item #2) to access the battery
compartment.
MACHINE SET UP & INSTALLATION
MACHINE OPERATION

ICE i15B 7
OPERATOR MANUAL
3. Carefully place the two batteries into the
compartment as shown in gure below.
DO NOT DROP BATTERIES INTO
COMPARTMENT!
4. Connect battery cables to posts as shown in
drawing below.
RED to POSITIVE and BLACK to NEGATIVE.
MACHINE SET UP
PRE-OPERATION CHECKS
1. Sweep or dust mop the surface to be cleaned.
2. Check battery meter to make sure batteries are
fully charged. (See BATTERY CHARGING)
3. Check that squeegee is properly installed.
4. Check that brush / pad is properly installed.
MOUNTING THE SQUEEGEE ASSEMBLY
1. Lift the Squeegee lift lever to the upward
position.
2. Mount the Squeegee assembly (see machine
components, p5 item #28) to the squeegee pivot
bracket. make sure the knobs are completely
seated into the slots before securing knobs.
3. Connect the vacuum hose to the squeegee
assembly. Loop the hose by using the hose clip
provided.
4. Check the squeegee blades for proper
adjustment.
FILLING THE SOLUTION TANK
The machine is equipped with a Solution ll-port
(see machine components, p5 item #8 )at the front
of the Solution tank, you can ll the solution tank
by using a hose or a bucket.
When using the bucket, stop lling when the level
reaches the bottom edge of the ll-port.
NOTE: When lling the solution tank with a buck-
et, make sure that the bucket is clean. Do not use
the same bucket for lling and draining the ma-
chine.
WARNING: Do not put any ammable
materials into solution tank. This can cause
an explosion or a re. Only use recommended
cleaning chemicals. Contact your Simple Clean
Scrubbers dealer for recommendations on
proper chemicals.
WHILE OPERATING MACHINE
WARNING: Fire Or Explosion Hazard. Do
Not Pick Up Flammable Materials Or Reactive
Metals.
1. Go slow on inclines and slippery surfaces. Do
not operate the machine on inclines that exceed
5% (3°).
2. Do not keep the machine in the same position
with pad / brush spinning, keep the machine
moving to prevent damage to oor nish.
3. If the squeegee assembly leaves streaks on the
oor, raise the squeegee o󰀨 the oor and wipe
the blades down with a damp cloth. Pre-sweep
the area to prevent leaving streaks on the oor.
4. Pour a recommended defoamer into the
recovery tank if excessive foam appears.
WARNING: Do not allow foam to enter
the oat shut-o󰀨 screen, vacuum motor dam-
age will result. Foam will not activate the oat
shut-o󰀨 screen.
5. Occasionally check the Battery meter, the indi-
cator displays the level of the batteries. When
meter is in the red, stop scrubbing and recharge
the batteries.
All green lights on: 100% level.
Yellow lights on, green lights o󰀨 : 50% level.
Red light on, other lights o󰀨: 20% level, the ma-
chine should be stopped and the batteries should
be recharged.
Red light ash: the batteries have already been
discharged deeply.
Red Yellow 2 Yellow 1 Green 2 Green 1

8ICE i15B
OPERATOR MANUAL
6. When the solution tank runs empty, turn o󰀨
the Brush motor switch and lift the brush head.
Keep the squeegee down and continue to vacu-
um until all the dirty water is picked up.
NOTE: See TANK DRAINING section to learn
how to drain recovery and solution tanks.
TANK DRAINING
1. Turn o󰀨 the machine.
2. With the squeegee and scrub head in their “up”
position, transport machine to approved area for
draining tank(s).
DRAINING THE RECOVERY TANK
Any time scrubbing is completed, or when relling
solution tank, the recovery tank should be drained
and cleaned.
WARNING: If the recovery tank is not
drained when the solution tank has been re-
lled, foam or water may enter the oat shut-
o󰀨 screen and cause damage to the vacuum
motor.
1. While holding the drain hose (see machine
components, p5 item #10) upward, remove the
cap and lower hose to drain.
2. Open the recovery tank cover and rinse out
the tank. Use a rag to remove any excess dirt.
Clean the oat shut-o󰀨 screen and debris tray
located in the recovery tank .
DRAINING THE SOLUTION TANK
Any time scrubbing operation is completed, the
solution tank should be drained and cleaned.
1. Pull the solution clear tube(see machine com-
ponents, p5 item #11) o󰀨 the hose tting, this
will allow the solution to ow freely into a bucket
or oor drain.
2. Remove the cover of the lter assembly to drain
the solution tank, check the lter screen and
clean up it if necessary.
3. Rinse the solution tank with clean water after
every use. This will help prevent chemical
buildup and clogging of the solution lines.
4. After rinsing out the tank, securely reconnect
the tank level hose to the hose tting, replace
the lter assembly cover and be sure the lter
screen and the “O” ring is in the correct posi-
tion.
BATTERY CHARGING
WARNING: Fire Or Explosion Hazard.
Batteries Emit Hydrogen Gas. Keep Sparks and
Open Flame Away. Keep Battery Compartment
Propped Open When Charging.
1. Transport the machine to a well ventilated area.
2. Turn the machine o󰀨.
3. If charging wet, lead acid, batteries check the
uid level before charging.
4. Connect the charger’s AC power supply cord to
a properly grounded receptacle.
5. The charger will automatically begin to charge,
you can watch the charging status on the win-
dow (machine components, p5 item #9), once
the charging cycle begins, the indicator lights
will progress from red, yellow to green. When
the green indicator light comes on, the charging
cycle is done. Unplug the charger cord.
NOTE: The machine will not operate when
charging.

ICE i15B 9
OPERATOR MANUAL
WARNING: Before performing any main-
tenance on the machine, be sure that the power
is turned o󰀨, or the batteries are disconnected!
WARNING: Repairs are to be completed
by Authorized service centers only. Any repairs
completed by unauthorized persons will void
the warranty.
DAILY MAINTENANCE
1. Remove pad driver/ brush and clean with ap-
proved cleaner.
2. Drain recovery and solution tanks completely
and rinse out with clean water. Visually check
the recovery tank for debris and clean out as
necessary.
3. Raise the squeegee assembly o󰀨 oor and wipe
it down with a damp towel. Be sure to store the
squeegee in the up position.
4. Remove the oat shut-o󰀨 assembly and rinse it
out with clean water.
5. Clean machine with an approved cleaner and a
damp towel.
6. Recharge the batteries.
7. Check the condition of the squeegee blade
wiping edge, rotate blade if worn.
MONTHLY MAINTENANCE
1. Clean the battery tops to prevent corrosion.
2. Check for loose battery cable connections.
3. Inspect and clean the recovery tank cover seal.
Replace it if damaged.
4. Lubricate all grease points and pivot points with
silicon spray and approved grease.
5. Check the machine for loose nuts and bolts.
6. Check the machine for leaks.
MOTOR MAINTENANCE
1. Contact your Simple Clean Scrubbers dealer for
any motor maintenance.
2. Motor should have the brushes checked every
250 hours. Brushes should be replaced when
they are worn to a length of 10 mm or less.
BATTERY MAINTENANCE
WARNING: Batteries emit hydrogen gas
and an explosion o re can result. Keep sparks
and re away from batteries at all times.
WARNING: Whenever servicing batteries,
be sure to wear protective gloves. Avoid con-
tact with battery acid at all times.
NOTE: For the best machine performance, keep
batteries properly charged at all times. Do not let
them sit in a discharged condition.
1. Always follow the battery charging directions as
outlined in the BATTERY CHARGING section of
this manual.
2. Keep battery tops and terminals free from corro-
sion. A strong solution of baking soda and water
is the best way to keep the batteries corrosion
free. DO NOT ALLOW THE BAKING SODA /
WATER SOLUTION TO ENTER THE BATTERY
CELLS.
3. Use a wire brush with the baking soda solution
to properly clean the battery posts and connec-
tions.
4. Check battery connections for wear and loose
terminals. Replace if necessary.
MACHINE STORAGE
1. Always store the machine indoors.
2. Always store the machine in a dry area.
3. Always store the machine in its upright position.
4. Always store the machine with the pad driver/
brush raised o󰀨 the oor.
5. If storing in an area which may reach freezing
temperatures, be sure to drain all uids from the
machine prior to storage. Any damage caused
by freezing temperatures will not be covered by
the warranty.
6. Drain the recovery tank.
7. Drain the solution tank of all uid.
PREVENTATIVE MAINTENANCE

10 ICE i15B
OPERATOR MANUAL
BASIC TROUBLESHOOTING
PROBLEM CAUSE SOLUTION
Machine will not
operate
Batteries need to be charged Charge batteries
Bad battery(s) Replace battery(s)
Loose battery cable Tighten loose cable
Brush motor will
not operate
Control handle trigger not pulled Pull control handle trigger
Tripped brush motor blown fuses Replace fuse
Bad brush motor switch Replace brush motor switch
Bad brush motor solenoid Replace brush motor solenoid
Faulty brush motor or wiring Contact ICE service Dealer
Worn motor carbon brushes Contact ICE service Dealer
Vacuum motor
will not operate
Bad vacuum motor switch Replace vacuum motor switch
Bad vacuum motor relay Replace vacuum motor relay
Faulty vacuum motor or wiring Contact ICE service Dealer
Worn Motor carbon brushes Contact ICE service Dealer
Little or no solu-
tion ow
Ball valve is shut o󰀨 Turn on the ball valve
Clogged solution tank lter or solution
hose
Clean solution tank lter or ush out solu-
tion hose
Clogged solution Solenoid valve Remove valve and clean
Poor water pick
up
Recovery tank is full Drain recovery tank
Loose drain hose cap Tighten cap
Clogged oat shut-o󰀨 screen located in
recovery tank Clean screen
Clogged squeegee assembly Clean squeegee assembly
Worn squeegee blades Replace or rotate squeegee blades
Incorrect squeegee blade deection Adjust squeegee blade height
Loose vacuum hose connections Secure hose connections
Clogged vacuum hose Remove clogged debris
Damaged vacuum hose Replace vacuum hose
Recovery tank lid not in place Properly position cover
Damaged recovery tank cover seal Replace seal
Faulty vacuum motor Contact ICE service Dealer
Low battery charge Recharge batteries
Short run time
Low battery charge Fully recharge batteries
Defective batteries Replace batteries
Batteries need maintenance See BATTERY MAINTENANCE
Faulty battery charger Repair or replace battery charger

ICE i15B 11
OPERATOR MANUAL
TECHNICAL SPECIFICATIONS
MODEL i15B
Brush Assist
DIMENSIONS L 31in / 790 mm
DIMENSIONS W 18.5 in / 468 mm
DIMENSIONS H 27 in / 690 mm
WEIGHT 93.7 lbs / 42.5Kg
WEIGHT WITH BATTERIES 140 lbs /63.5 Kg
RECOVERY TANK CAPACITY 5Gal / 19 L
SOLUTION TANK CAPACITY 4Gal / 15 L
SQUEEGEE WIDTH 18 in / 450 mm
CLEANING PATH WIDTH 15 in / 381 mm (Disk)
DRIVE SYSTEM Brush Assisted
BRUSH MOTOR 0.27hp / 0.2KW
140 RPM
VACUUM MOTOR 0.54hp / 0.4KW
WATER LIFT - AIR FLOW 45 in / 1,143 mm
BATTERIES 2-12，33Ah @ 20 hr
RUN TIME PER CHARGE 1.2 Hours
VOLTAGE DC 24V
DECIBEL RATE AT
OPERATOR'S EAR, INDOORS 78dB(A)
GRADE LEVEL, MAX 5% (3°)

12 ICE i15B
PARTS LIST
RECOVERY TANK GROUP

ICE i15B 13
PARTS LIST
RECOVERY TANK GROUP
DIA
NO.
PART
NUMBER DESCRIPTION NO. REQ'D
1 8401204 TOP COVER OF RECOVERY TANK 1
2 8401205 LOWER COVER OF RECOVERY TANK 1
3 1421409 FLAT WASHER M4×DIA9×0.8 8
4 1321110 SCREW,ST3.5×10 9
5 8401207 RECOVERY TANK COVER SEAL 1
6 8401206 RECOVERY TANK COVER SEAL 1
7 8401208 FLOATING BLOCK 1
8 1421425 FLAT WASHER,DIA4.3×DIA25×1.5 1
9 4010316 ICE LOGO 1
10 8401201 RECOVERY TANK 1
11 8401210 VACUUM HOSE 1
12 8401211 DRAIN HOSE 1
13 1962032 CLAMP 1

14 ICE i15B
PARTS LIST
SOLUTION TANK GROUP

ICE i15B 15
PARTS LIST
SOLUTION TANK GROUP
DIA
NO.
PART
NUMBER DESCRIPTION NO. REQ'D
1 1221612 SCREW,M6×12 4
2 1422616 LOCK WASHER, M6 6
3 1421616 FLAT WASHER M6×DIA16×1 4
4 8401212 SEAL PACKING 1
5 8401213 BACKSTOP 1
6 8401203 VACUUM MOTOR,24VDC 1
7 8401209 MOUNTING PLATE 1
8 1421409 FLAT WASHER M4×DIA9×0.8 8
9 1422411 LOCK WASHER, M4 8
10 1321213 SCREW,ST4×13 4
11 8310208 ISOLATER, M6 4
12 8401202 FILLER COVER 1
13 8050153 CHAIN 1
14 1321110 SCREW,ST3.5×10 2
15 8401101 SOLUTION TANK 1
16 8401121 TWIST CAP 1
17 8401102 MAIN FRAME 1
18 1421824 FLAT WASHER M8×DIA24×2 4
19 1422821 LOCK WASHER, M8 6
20 1021820 SCREW,M8×20 6
21 1421828 FLAT WASHER M8×DIA28×3 2
22 8401108 WHEEL,10 INCH 2
23 8401127 BUSHING 2
24 1511525 SCREW,M5×25,HEX SOCKET 4
25 4010405 HOOK,CABLE 2
26 1221310GL SCREW,M3×10,HEX HEAD 4
27 8401131 PIPE CLAMP 2
28 1221410 SCREW,M4×10 6
29 8401133 TAGS 1
30 6210503 ROCKER SWITCH 1
31 1123305 NUT,LOCK M3 2
32 8401104 REAR COVER 1
33 1221510 SCREW,M5×10 2
34 8144707 RELAY 40A 2

16 ICE i15B
PARTS LIST
SOLUTION TANK GROUP
DIA
NO.
PART
NUMBER DESCRIPTION NO. REQ'D
35 1123406 NUT,LOCK M4 2
36 8401107 BATTERY CHARGER 1
37 8401103 MOUNTING PLATE 1
38 8401132 MOUNTING PLATE 1
39 1421612 LOCK WASHER, M6 2
40 1021616 SCREW M6×16 2
41 8401711 BATTERY CONNECT CABLE,RED 2
42 8401712 BATTERY CONNECT CABLE,BLACK 1
43 8401713 BATTERY CONNECT CABLE,RED 1
44 8401710 BATTERY 2

ICE i15B 17
PARTS LIST
HANDLE ASSEMBLY

18 ICE i15B
PARTS LIST
HANDLE ASSEMBLY
DIA
NO.
PART
NUMBER DESCRIPTION NO.
REQ'D
18014063 BATTERY CAPACITY METER 1
21885301 POWER CONTROL SWITCH 1
31211410 SCREW, M4×10 4
4 8401704 DECAL,CONTROL PANEL 1
58401703 CONTROL PANEL 1
6 1512625 SCREW, M6×25 2
7 1421616 FLAT WASHER M6×∮16×1.0 4
88401401 THE HANDLE BACK COVER 1
9 1512635 SCREW, M6×35 2
10 1211512 SCREW, M5×12 4
11 1434500 TOOTH WASHER,∮5 4
12 8401402 BOBY 1
13 8401405 CONTROL LINE PROTECTION RING 1
14 8401403 PULL ROD 1
15 4010207 SEAT,SPRING 1
16 4010216 SEAL,SEAT 1
17 4010208 SPRING,LEVELING 1
18 1111403 NUT M4 1
19 4010211 INSERT 1
20 1511530 SCREW, M5×30 4
21 1511540 SCREW, M5×40 2
22 1521620 SCREW, M6×20 4
23 4010110 SHAFT 1
24 4010114 WASHER 1
25 1222512 SCREW, M5×12 1
26 1521845 SCREW, M8×45 1
27 5012416 HANDLE,STAND,LEFT 1
28 1123608 NUT M6 4
29 1212410 SCREW, M4×10 2
30 4010212 COVER 2
31 4010202 COVER,SEAT GEAR 1
32 8401404 GEAR 1
33 4010201 MOUNTING BASE,GEAR 1
34 1123507 NUT M5 8
35 8401415 MOUNTING BRACKET 1
36 1421510 FLAT WASHER M5×∮10×1.0 2
37 1422616 LOCK WASHER, M6 4
38 1421612 FLAT WASHER M6×∮12×1.0 4
39 5012415 HANDLE,STAND,RIGHT 1
40 1421618 FLAT WASHER M6×∮18×1.6 3
41 8113111 NYLON FLAT WASHER ∮12.9×∮25.4×0.8 2
42 8401411 DIGGING ROPE 1

ICE i15B 19
PARTS LIST
HANDLE ASSEMBLY
DIA
NO.
PART
NUMBER DESCRIPTION NO. REQ'D
43 8014101 LIFTING ROPE SPACER 1
44 8401407 RAISE THE HANDLE 1
45 8401413 AXLE SLEEVE 1
46 1021630 HEX HEAD BOLT M6×30,SS 1
47 1021620 HEX HEAD BOLT M6×20,SS 1
48 4010317 SEAT,BALL 1
49 1211408 SCREW, M4×8 2
50 1123406 NUT M4 1
51 1421412 FLAT WASHER M4×∮12×1.0 1
52 4010304 LEVELONG ROD 1
53 8113104 BALL KNOB M8 1
54 4010330 TRIGGER,SWITCH,RIGHT 1
55 4010331 TRIGGER,SWITCH,LEFT 1
56 4010314 PIN 4
57 1221406 SCREW M4×6 2
58 4010311 CLAMP,CORD 1
59 4010323 SPRING,SWITCH 1
60 1211325 SCREW M3×25 2
61 1434300 TOOTH WASHER M3 2
62 4010308 SWITCH 1
63 4010307 SAFETY BOTTOM 1
64 4010333 SPRING,SAFTY 1
65 8401408 FRONT COVER 1
66 4010316 ICE,LOGO 1

20 ICE i15B
PARTS LIST
SCRUB HEAD GROUP