Icecrypt S3250CCIHD User manual

1
CONTENTS
1. SAFETY.............................................................................................................................................................3
2. INTRODUCTION.............................................................................................................................................3
3. FEATURES........................................................................................................................................................4
4. REMOTE CONTROL......................................................................................................................................5
5. FRONT PANEL ................................................................................................................................................7
6. REAR PANEL...................................................................................................................................................7
7. CONNECTING YOUR SYSTEM ...................................................................................................................8
8. BASIC OPERATIONS .....................................................................................................................................9
8.1 TURN ON STB.....................................................................................................................................................9
8.2 POWER ................................................................................................................................................................9
8.3 CHANNEL UP/CHANNEL DOWN...........................................................................................................................9
8.4 VOLUME UP/VOLUME DOWN- ............................................................................................................................9
8.5 NUMBER..............................................................................................................................................................9
8.6 MUTE..................................................................................................................................................................9
8.7 PAUSE .................................................................................................................................................................9
8.8 RECALL...............................................................................................................................................................9
8.9 FAVOURITE .......................................................................................................................................................10
8.10 AUDIO.............................................................................................................................................................10
8.11 INFORMATION .................................................................................................................................................10
8.12 EPG (WHERE AVAILABLE) .............................................................................................................................10
8.13 TV/RADIO.....................................................................................................................................................11
8.14 CHANNEL LIST................................................................................................................................................11
8.15 SLEEP..............................................................................................................................................................12
8.16 PAGE UP/PAGE DOWN.....................................................................................................................................13
8.17 TEXT..............................................................................................................................................................13
8.18 SUBTITLE ........................................................................................................................................................13
8.19 FIND................................................................................................................................................................13
8.20 ZOOM ............................................................................................................................................................13
8.21 TV/ SAT.........................................................................................................................................................13
8.22 MENU..............................................................................................................................................................13
8.23 VIDEO FORMAT...............................................................................................................................................13
8.24 EXIT................................................................................................................................................................14
9. SERVICE.........................................................................................................................................................14
9.1 ORGANIZING SERVICES.....................................................................................................................................14
9.2 ORGANIZING FAVOURITES ................................................................................................................................16
10. INSTALLATION ............................................................................................................................................16
10.1 SATELLITE INSTALLATION ..............................................................................................................................16
10.2 AUTO INSTALLATION ......................................................................................................................................19
10.3 SATELLITE GUIDE ...........................................................................................................................................19
10.4 TERRESTRIAL INSTALLATION..........................................................................................................................19
10.5 CABLE INSTALLATION.....................................................................................................................................20
11. PREFERENCE................................................................................................................................................20
11.1 LANGUAGE......................................................................................................................................................21
11.2 PARENTAL CONTROL ......................................................................................................................................21
11.3 A/V CONTROL.................................................................................................................................................22
11.4 TIME SETTING.................................................................................................................................................23
11.5 TIMER .............................................................................................................................................................23
11.6 MISCELLANEOUS SETTINGS ............................................................................................................................24
11.7 OSD SETTING .................................................................................................................................................25
12. SYSTEM ..........................................................................................................................................................26

2
12.1 INFORMATION.................................................................................................................................................26
12.2 DEFAULT SETTING..........................................................................................................................................26
12.2.1 Default Value: ..........................................................................................................................................26
12.2.2 Delete All Channels:.................................................................................................................................27
12.2.3 Save default value.....................................................................................................................................27
12.3 SOFTWARE UPGRADE......................................................................................................................................27
12.4 UPGRADE BY USB..........................................................................................................................................28
12.5 BACKUP TO USB.............................................................................................................................................28
13. CONDITIONAL ACCESS.............................................................................................................................28
13.1 CA SETTING....................................................................................................................................................28
13.2 COMMON INTERFACE......................................................................................................................................29
14. USB...................................................................................................................................................................29
14.1 FILE LIST.........................................................................................................................................................29
14.1.1 Record Files...............................................................................................................................................30
14.1.2 MP3 Files...................................................................................................................................................30
14.1.3 Image Files.................................................................................................................................................32
14.1.5.Software .....................................................................................................................................................33
14.1.6All................................................................................................................................................................34
14.2 STORAGE INFORMATION .................................................................................................................................34
14.3 PVR SETTING..................................................................................................................................................34
14.4 USB SPEED TEST ............................................................................................................................................35
14.5 REMOVE USB DEVICE SAFELY!......................................................................................................................35
15. INTERNET......................................................................................................................................................35
15.1 NETWORK LOCAL SETTING.............................................................................................................................35
15.2 HTTP UPGRADE...............................................................................................................................................36
15.3 FTP UPGRADE ................................................................................................................................................36
15.4 FTP.................................................................................................................................................................37
15.5 WEATHER FORECAST......................................................................................................................................37
15.6 RSS READER ..................................................................................................................................................37
15.7 WIFI MANAGER..............................................................................................................................................38
15.8 NET MEDIA.....................................................................................................................................................38
15.9 GOOGLE MAPS................................................................................................................................................39
16. GAME ..............................................................................................................................................................39
16.1 TETRIS ............................................................................................................................................................39
16.2 SNAKE ............................................................................................................................................................39
16.3 OTHELLO ........................................................................................................................................................40
17. NEW FEATURES...........................................................................................................................................40
17.1 EQUALIZER .....................................................................................................................................................40
17.2 TIME SHIFT .....................................................................................................................................................40
17.3 RECORD ..........................................................................................................................................................41
18. TROUBLE SHOOTING.................................................................................................................................42
19. SPECIFICATIONS.........................................................................................................................................43

3
1. SAFETY
This HD Receiver has been manufactured to satisfy the international safety standards.
Please read the following safety precautions carefully.
MAINS SUPPLY: 100~240V AC, 50/60Hz
OVERLOADING: Do not overload wall outlet, extension cord or adapter as this may result in fire or
electric shock.
LIQUIDS: Keep liquids away from the HD Receiver. The apparatus shall not be exposed to dripping
or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
CLEANING: Disconnect the HD Receiver from the wall outlet before cleaning .Use a light damp cloth
(no solvents) to dust the HD Receiver.
VENTILATION: The slots on top of the HD Receiver must be left uncovered to allow proper airflow to
the unit. Do not stand the HD Receiver on soft furnishings or carpets. Do not expose the HD Receiver
to direct sunlight or do not place it near a heater. Do not stack electronic equipments on top of the HD
Receiver.
ATTACHMENTS: Do not use any attachments that are not recommended as these may cause
hazard or damage the HD Receiver.
CONNECTION TO THE SATELLITE DISH LNB: Disconnect the HD Receiver from the mains before
connecting or disconnecting the cable from the satellite dish.
FAILURE TO DO SO CAN DAMAGE THE LNB.
CONNECTION TO THE TV: Disconnect the HD Receiver from the mains before connecting or
disconnecting the cable from the satellite dish.
FAILURE TO DO SO CAN DAMAGE THE TV.
EARTHING: The LNB cable MUST BE EARTHED to the system earth for the satellite dish.
LOCATION: Place the HD Receiver indoor in order not to expose to lightening, rain or sunlight.
2. INTRODUCTION
Thank you for purchasing the Icecrypt S3250CCIHD Receiver.
This HD Receiver is fully compliant with the international DVB standard and thus transmits digital
images, sounds, information guides and Teletext directly to your TV through the satellite, terrestrial
and cable broadcasts.
Now you can comfortably see and receive digitally transmitted music, news, movie and sports
broadcasts in your office or at your home. You can enjoy interesting games embedded in HD
Receiver.
In service search section, both the automatic service search method and the manual search mode
are provided. Also it supports DiSEqC 1.0, 1.2 and USALS, enabling you to move your antenna in
order to focus on preferred satellite. You can save up to 6000 TV and Radio services and work with a
Favourite, Lock, Delete, Move and Sort function.
The menu is very modern and supports multiple languages. All functions can be carried out using the
remote control and some of the functions can also be carried out using the front panel. The HD
Receiver is easy to use and adaptable for future advances. Please be aware that new software may
change the functions of the HD Receiver.

4
If you have any difficulties concerning the operation of your HD Receiver, please refer to the relevant
section of this manual, including the ‘Troubleshooting’. This Manual will provide you with useful
information on using the HD Receiver.
3. FEATURES
MPEG-Fully DVB-S/DVB-S2/DVB-T/DVB-T2/DVB-C/DVB-C2 (H.264) HD compliant
6000 channels (TV and Radio) programmable
Multilingual menu text support
Channel switching time less than 1 second
Channel list editing
Favourite channel list editing
True-colour On-Screen Display (OSD)
Full Picture In Graphic (PIG) function
Electronic Programme Guide (EPG) for on screen channel information
Subtitle supported
Teletext supported by VBI insertion and software emulation
Parental lock facility by channel and programme event
Programme and Channel information transfer from receiver to receiver
Exciting games embedded
Dolby Digital Bit-Stream output via HDMI
DiSEqC 1.0, 1.1, 1.2 and USALS
HDMI Full HD (1080p) Video/Audio Output
2x USB 2.0 Host
VFD Display for service information
RTC (Real-Time-Clock)
Time Shift
Video Recording
Record one channel and Time Shift another channel (optional)

5
4. Remote Control
You can power on/off the receiver, operate on screen menu, and
use a variety of hot key functions.
POWER
To switch your receiver on from standby.
MUTE
Used to enable or disable the audio
NUMERIC KEYS
Used to select channels or enter programming parameters
TV / RADIO
Receiver switches between TV and Radio mode.
(ZOOM)
Press key select zoom times, from X1 to X16.
RECALL
Return to the previous menu or status.
TV/SAT
Receiver switches between TV and Receiver mode.
INFO
To display channel status or various programme information of current
service.
EPG (Electronic Programme Guide)
Display the Programme Guide on screen when available.
MENU
Displays the Main Menu on the screen, or return to the previous menu or
status.
EXIT
Cancel the user selection and return to the viewing mode from a menu.
OK
To select menu option, or to update an entry.
<,> KEY
To adjust volume level, or to move cursor left or right in the menu.
^,v KEY
To change channels, or to move cursor up or down in the menu.
PAGE+/PAGE-
To move the cursor to the next or previous page
in the menu or channel list.
●REC
Has a different function per menu.
Teletext
Shows Teletext information of the current channel (if supported).
Subtitle
Subtitle Display.
UHF
If your TV is connected through RF Modulator (UHF), select output channel
number between CH21 and CH69 with up and down key.
(FIND)
Find channels sort by Letter/Name.
TIMER
Press timer key so you can setup up the Standby time.
V ． FORMAT
Press P/N button to switch the display mode among "Auto-> by native
TV<->480i->480p ->576i-> 576P-> 720p-50-> 720p-60-> 720P-60->
1080i-50->1080i-60 ->1080p-50->1080p-60".
FAV (FAVOURITE)
To set receiver to the favourite server mode,
Display the favourite channel.
FOLDER
Press this button to enter the Recording Manager menu directly.
AUDIO (Red Key)
Audio channels setup, to select audio mode; Left, Right, Stereo, Mono.
OPTION (GREEN KEY)
Shows NVOD information of the current channel supports.
SAT
Display the satellite list as normal picture.

6
Play Mode
Select the play mode in MP3 or JPEG player.
USB
To remove the USB Hard Disk safely.
TMS (Time Shift)
Press this button to display Time Shift info bar.
Play
To play the MP3, JPEG, or Record files.
Stop
To stop the Time Shift, recording, or MP3/JPEG player.
PAUSE
Used to select the freeze function.
Press once to freeze the screen picture.
FB
To start Fast Backward function.
FF
To start Fast Forward function.
SB
To start Slow Backward function.
SF
To start Slow Forward function
/ PREV/NEXT
Switch to preview or next file in play mode

7
5. Front panel
POWER KEY: To switch the receiver power on/stand by.
MENU KEY：To enter the Main Menu.
◄►KEY: To adjust volume level, or to move cursor left or right in the menu.
▲ ▼ KEY: To change channels, or to move cursor up or down in the menu.
OK KEY: To see TV/Radio channel list, or to confirm in the menu.
Remote Sensor: Detects infrared signal from remote control unit.
POWER Indicator: Lit whilst the receiver is powered on and at standby mode.
Signal Indicator: When received signal is strong, the signal indicator is lit.
Card Slot: One slot CA Interface for Conax.
Common Interface: One socket for Conditional Access Modules CAM.
USB: USB 2.0 Host, connect to USB hard disk, or flash disk.
Display: (VFD type) Indicates operating status of receiver.
6. Rear Panel
Please refer to the diagram above for all possible connections of your receiver
Do not connect the unit to the mains socket until all other connections have been made and checked.
POWER ON/OFF SWITCH: To switch ON/OFF the receiver power supply.
LOOP: This enables the connection of another receiver.
LNB IN 13/18V 500mA MAX: This port is to connect the coaxial cable from LNB of your Dish.
RF OUT: This enables the connection of another receiver.
RF IN: This port is to connect the coaxial cable from Terrestrial/Cable Antenna.
AERIAL OUT: This enables the connection of another receiver.
AERIAL IN: This port is to connect the signal cable from Terrestrial/Cable Antenna.
TV: This is used to connect your TV through SCART cable.
VIDEO: This RCA connector is used to connect any external video.
AUDIO R/L: These RCA connectors are used to connect any external audio amp or system.
0/12V 50mA: This is used to connect 12V to an external 0V/12V switch.
S/PDIF: Digital Audio interface, connect to AV amplifier S/PDIF input terminal.
RS 232C SERIAL PORT: This is used to connect your receiver to a computer through a serial cable.
HDMI: Audio and Video output socket for TV set with HDMI Input Jack only.
USB: USB 2.0 Host, connect to USB hard disk, or flash disk
Ethernet: Network port, you can get a new software updates from this port.

8
7. Connecting Your System
There are two ways to connect the receiver to your existing TV system. We recommend using one of
the following cases for the best result:
1. If you have a high definition television set, you should use a HDMI cable for best result, Plug one
end of the cable into the HDMI socket on the receiver, and the other end into the matching socket on
your television. In this case, you do not have to make audio connections because the HDMI connector
can output stereo audio or Dolby Digital audio.
2. Connect one end of SCART cable to the TV (SCART) jack on the back of the receiver and the other
end to a SCART jack on your TV.
3. Connect one end of RCA cable to the RCA jack on the back of the receiver and the other end to a
RCA jack on your TV.
Finally connect the coaxial cable from the LNB of your Dish to the LNB IN jack on the receiver.
With External Audio / Hi-Fi System
To connect any external Audio Hi-Fi system, the receiver has been provided with RCA connector at
the back of the receiver marked with AV OUT.
Connect an RCA cable from the AV OUT jack on the back of the receiver to the LINE, AUX, SPARE
or EXTRA input jacks on your Hi-Fi System.
7.1 TV with Motorized System (DiSEqC 1.2)
Connect one end of your coaxial cable to the LNB IN connector on the receiver and the other end to
the REC or Receiver connector on the DiSEqC 1.2 motor.
Connect the coaxial cable from the LNB to the LNB connector on the DiSEqC 1.2 motor.
All our receivers are designed to be DiSEqC 1.0 and DiSEqC 1.2 compatible.
This allows multiple antennas to be connected to the receiver at the same time.
If you have two or more fixed antennas or LNBs, then we recommend you use a DiSEqC 1.0
switch.
Connect the coaxial cable from the first LNB to the LNB 1 or LNB A input connector of the DiSEqC
switch.
Do the same for any other LNBs that you have.
Connect one end of a coaxial cable to the RF output connector of the DiSEqC switch,
connect the other end to the LNB IN socket on the receiver.
To the digital receiver, you can connect either a single satellite antenna directly or LNB of
multi-feed equipment.

9
8. Basic Operations
8.1 Turn on STB
First, press the [Device’s Main Power] to turn on
the unit. When the STB is first used it will show
the Main Menu. If channels are already installed
the, STB will play the same channel as last time
before turning off.
Frequently Asked Questions
Q: The power of my STB has been turned on
and not in Standby mode, but the TV
screen showed nothing:
A: Make sure the TV set has been set to the
correct video input (not the TV channels). For
example, if you have connected the unit with the
Video1 input of the TV set, the TV set has to be
switched to Video1.
Q: The power of my STB has been turned on
(not in Standby mode), but the TV screen
showed nothing except one box with “No
Signal”image.
A: This means there is no signal for the channel
which you have selected. It could be several
causes:
1 The channel which you selected is not on
your allocated satellite. The simple solution
is to change channel.
2 The signal of current TV channel is too
weak. You can try to change channel to a
stronger signal channel. If the problems still
exist, please consult your local dealer or
other professionals for technical service.
3 You are using a different LNB, and you
need to Modify LNB Type
8.2 Power
1 Press [Power] Key can enter the Standby
state.
2 In Standby state, press [Power] Key again
to wake the unit and go on to view the last
channel.
3 User can also disconnect the device’s main
power to end the Standby state.
8.3 Channel Up/Channel Down
In full screen, press [CH+/CH-] to change
channel.
8.4 Volume Up/Volume Down-
In full screen, press [VOL+/VOL-] to adjust
volume.
8.5 Number
In full screen, use number key and press [OK]
on the Remote Control Unit to change channel.
8.6 Mute
1 Press [MUTE] key to mute the sound and
the screen will show up mute OSD.
2 Press [MUTE] key again to restore sound.
8.7 Pause
1 In play mode, press [Pause] key, the
picture will be paused, but the sound of the
channel will still continues.
2 Press [PLAY] key again, the screen’s
picture will skip over to the live picture, and
the sound of the channel will correspond to
the live image.
8.8 Recall
Press [RETURN] key to directly switch to the
previous channel that you viewed before current
channel.

10
8.9 Favourite
1 In full screen, press [FAV] key, it will display
a window of “Favourite list” on the left of the
screen, which you can see like below.
2 In the window of “Favourite list ", you can
move highlight by press [Channel
Up/Channel Down] key to select favourite
Channels.
3 In the window of ” Favourite list ", you can
press [Left/Right] key to select favourite
groups Pressing [P-/P+] keys can
implement the “Page up/Page down”
function
4 Press [Exit] key to exit the current window.
Frequently Asked Question
Q: Why the screen displays “No Favourite
Channel”, after pressing [Favourite] key?
A: It is because that you haven’t set any
channels as “Favourite Channel”. Please
refer to Favourite
.
8.10 Audio
1 In full screen, press [AUDIO] key to open
the “Audio”window on the screen.
2 You can modify the audio track by pressing
[Channel Up / Channel Down] key and
modify the audio mode by pressing
[Volume Up / Volume Down] key.
3 Mode: Left/Right/Stereo/Mono
8.11 Information
In full screen, press [INFO] key (press [INFO]
key and [RED] key) to open information screen;
the window shows the parameters of current
channel.
8.12 EPG (Where Available)
1 The STB has an Electronic Programme
Guide (EPG) to help you navigate channels
through all the possible viewing options.
The EPG supplies information such as
channel listing and start and end times for
all available channels.
Press [EPG] key to display EPG screen.

11
2 Press [Red] key to select the channels by
different groups, such as by
Favourite/Satellite/Provider/CAS etc.
3 Press [Green] key to select different display
modes including “Now EPG”, “Next EPG”,
“More”and “Schedule”, like the below
image:
4 Press [Yellow] key in EPG menu to set one
record timer or go to Timer List menu.
5 In EPG menu, when you select one event
by highlighting item, you can set this event
to record directly by pressing [REC] button.
6 In EPG menu, press [Exit] to close EPG
screen.
8.13 TV/RADIO
In TV mode, pressing [TV/RADIO] key can
switch to Radio mode. In Radio mode, press
[TV/RADIO] key to switch to TV mode.
8.14 Channel List
1 In full screen, press [OK] key can enter
“Channel List”.

12
2 Press [Red] key to change the group.
Which you can see below.
3 Press [Green] key to display detailed
information for EPG Now.
Press [Yellow] key you to change the current
channel’s property, such as FAV/ Lock/ Skip/
Delete/ Rename.
4 Press [Blue] key to open the “Sort”window
like below. There are five kinds of ways to
sort. You can press [Channel Up/Channel
Down] key to move highlight and press
[OK] key to confirm your selection.
5 The five ways to sort are:
Default: Sort by scan result.
FTA/$: Sort channels through free and
scrambled sequence. Free channels
will be listed first and scrambled
channels will at the back.
Lock: Accumulate all locked channels
and list at the end of TV Channel List.
Name (A-Z): Sort in Alphabetical Order
(ignore “$”symbol).
Name (Z-A): Sort in Alphabetical Order
(ignore “$”Symbol).
6 Press [Up/Down] key to move highlight and
press [OK] key to play the highlighted
channel.
7 Press [Page Up/Down] key to page up and
page down.
8 Press [Exit] key to exit the channel list.
8.15 Sleep
1 This function can set sleep timer. When
you set a sleep timer and the time arrives,
the system will enter standby
automatically.
2 Pressing [SLEEP] key will switch the mode
between Sleep Timer Off /10/30/60/90/120
minutes.

13
8.16 Page Up/Page Down
In Channel list, press [Page+/Page-] key to page
up and page down in the channel list.
8.17 TEXT
1 Press [TTX] key in full screen, you can
open Teletext page on a channel which has
Teletext information.
2 If the channel has no Teletext information,
it will show “No Teletext Data”on the
screen.
8.18 Subtitle
Press [Subtitle] key in full screen to switch
subtitles “On”or “Off”.
8.19 Find
1 Press [Find] key in full screen to open the
“Find” window like above. You can press
[Channel Up/Channel Down/Volume
Up/Volume Down] key to move highlight
and press [OK] key to input the selected
symbol or letter into the Find Box.
2 After entering each character, the
programme list on the left will search the
channel according your input, and list the
matched channel.
3 Move highlight to “OK” and press [OK] key
to close “Find” window and you can select
channel from the channel list directly.
8.20 Zoom
1 The [ZOOM] key allows you to magnify a
certain area on the screen.
2 Press [ZOOM] key again, the image will
enlarge x1, x2, x4, x6, x8, x12, x16.
3 In “x2 ~ x16”image, using [Up/ Down/ left/
right] keys to move the image area you
want to see.
4 In zoom mode, press [Exit] to close “Zoom”
window.
8.21 TV/ SAT
Press [TV/ SAT] key to switch between TV
mode and STB mode
8.22 Menu
Press [MENU] key to open the menu, exit the
current menu to last menu or close the
window.
8.23 Video Format
Press [P/N] (white) key under Full Screen
playback to show the current video resolution.
Press this key again to video resolution in the
sequence “480i->480p ->576i-> 576P->
720p-50-> 720p-60-> 720P-60->
1080i-50->1080i-60 ->1080p-50->1080p-60”.

14
8.24 Exit
Press [EXIT] key to exit the current menu, to
return to last menu, or close the window.
9.Service
When you press [Menu] key to enter menu,
there will display the picture like below:
Press [Up/Down] key to select the
submenu of organizing services and
organizing favourites.
Press [OK] key to enter the “Organizing
Service”. If Menu Lock is “On”, it will display
a dialogue for user to key in password. The
default Password is “0000”.
Press [Menu] key to go back to main menu.
9.1 Organizing Services
When you enter “Organizing Services”menu,
you will see a screen like below.
1. You can move highlight by pressing
[Channel Up/Channel Down] key and [OK]
key to select the programmes which you
want to edit.
2. You can press [Page Up/Page Down] key
to implement the Page Up/Page Down
function.
3. You can use [Red] key to switch to a
different Group.
4. You can press [Green] key to select the
programmes by a different mode.
5. Pressing a colour key can implement the
corresponding function in “Organizing
Services”.
Groups
1 Press [Red] key to open the “Groups”window
like above
2 You can press [Up/Down] key to move
highlight and press [OK] key to select group.
3 Press [Menu] key to close “Groups”List.
Options

15
1. Press [Green] key to open the “Options”
window like above.
2. You can press [Up/Down] key to move
highlight and press [OK] key to confirm the
selection.
3. Press [Menu] key to close “Options”List.
Move
1. Select the channels which you want to edit
in channel list by pressing [OK] key.
2. Then press [Right] key to move the high
light to right toolbar.
3. Select Move icon by pressing [Channel
Up/Channel Down] key and [OK] key.
4. Move the channels to the position which
you want and press [OK] key to confirm.
Like the following picture:
Lock
1 Select the channels which you want to edit in
channel list by pressing [OK] key.
2 Then press [Right] key to move the high light
to right toolbar.
3 Select Lock icon by pressing [Channel
Up/Channel Down] key and [OK] key.
4 Lock the channel by pressing [OK] key.
Like the following picture:
Delete
a) Select the channels which you want to
edit in channel list by pressing [OK] key.
b) Then press [Right] key to move the high
light to right toolbar.
c) Select Delete icon by pressing [Channel
Up/Channel Down] key and [OK] key.
d) Delete the channel by pressing [OK]
key.
Skip and rename
In the same way you can set a channel to Skip,
or rename a selected channel.
Find

16
1. Press [Find] key to open the “Find”window
like above. You can press [Channel
Up/Channel Down/Volume Up/Volume
Down] key to move highlight and press [OK]
key to input the selected symbol or letter
into the find box.
2. After inputting each character, the
programme list on the left will search the
channel according your selection, and list
the matched channels.
3. Move highlight to “OK”and press [OK] key
to close “Find”window and you can select
channel from the channel list directly.
9.2 Organizing Favourites
This menu is helpful in adding and deleting
services to and from the Favourite Group.
1 FAV List
To choose the FAV List press “FAV” button.
2 Add
To add services to Favourites: Mark the desired
service(s) by pressing “OK” button in Service
List, press to choose Add mode and press
“OK” button.
3 Remove
To remove services from Favourites: Mark the
desired services by pressing “OK” button in
Favourite List, press to choose Remove
mode and press “OK” button.
4 Move
You can reorder and move the services to your
preferred position in Favourites List.
5 Rename
Select the desired FAV List by pressing “FAV”
button, using , buttons to choose Rename
mode and press “OK” button to display
keyboard, and rename service.
6 Group, Options and Find functions
Please refer to the “Organizing Services”part in
this manual.
10. Installation
1 Press [Left/Right] key to select menu
pages; Service, Installation, Preference,
System, Conditional Access, Internet,
USB and Game.
2 Press [OK] key to enter the “Installation”.
If Menu Lock is “On”, it will display a
message for user to key in password. The
default Password is “0000”.
3 Press [Up/ Down] key to select menu
items. Press [menu] key to go back to
main menu.
10.1 Satellite Installation Satellite
1 Satellite: Press [OK] key to enter the
Satellite list.

17
2 Press [Up/ down] key to select satellite.
Press [Page] key to page up or page down.
LNB Type
In this option press[Volume Up/ Volume
Down]key to switch among “Standard”, “User”,
“Universal”and ”Unicable”mode.
DiSEqC
DiSEqC: You can use [Volume Up/ Volume
Down] key to switch options. There are
several options for your selection:
a) Disable: No DiSEqC.
b) 1/2, 2/2: two DiSEqC ports.
c)1/4, 2/4, 3/4, 4/4: 4 DiSEqC ports.
d) 1/8, 2/8… 8/8: 8 DiSEqC ports.
e) 1/16, 2/16….16/16: 16 DiSEqC ports.
Positioner
Positioner：In “Positioner”option, you can press
[Volume Up/ Volume Down] key to switch “Off /
DiSEqC 1.2 / USALS”functions.
22K
You can use [Volume Up/ Volume Down] key to
switch “ON / Off”. When this option is switched
“ON”, receiver will receive TV and radio input
signals from 22K port. If the option is switched
“Off”, the receiver will receive all signals from 0K
port.
Notice!
When you choose LNB type “Universal”, you
cannot modify 22K.
0/12V
You can use [Left/ Right] key to switch “on /off”.
Polarity
In “Polarity”option, [Volume Up/ Volume Down]
key switches “Auto / H / V”functions.
Toneburst
In “Toneburst”option, you can press [Volume
Up/ Volume Down] key to switch “Off/On”
function.

18
LNB Power
In “LNB POWER” option, you can press [Volume
Up/ Volume Down] key to switch:” Off、13v/18v、
13.5V/18.5V” functions.
TP Edit
When you enter “TP Edit”menu you will see a
screen like below:
1 In “Satellite”option press [Volume Up/
Volume Down] key to switch to the satellite
that you want to scan, or press [OK] key to
enter satellite list for selection.
2 In “TP Index”option, you can not only use
[Volume Up/ Volume Down] key to select
transponder but also can use [Add] and
[Delete] functions.
When you press [Green] key, it will display
“New TP”in “TP Index”item; you should set
the parameters of “TP Frequency”and
“Symbol Rate”for this new transponder.
The parameters of “TP Frequency”and
“Symbol Rate”can set by number keys.
The available range are “3000~13450
MHz”and “1000~45000Ks/s”.
When you press [Yellow] key you will see a
warning message asking for confirmation to
delete the current transponder. If you select
“Yes”, the current transponder will be
deleted, and the total amount of
transponders will reduce correspondingly.
When you press [Blue] key you will see a
warning message asking for confirmation to
delete all transponders. If you select “OK”,
all transponders will be deleted.
3 For the existing transponder, you also can
use number keys to modify the parameters
of “TP Frequency”and “Symbol Rate”.
4 When you complete your modification,
Press [Red] key to see an option asking
you Scan Mode, Programme Type, Scan
Type and NIT Search On/Off. After you set
these up, press [OK] key to start scanning.
5 In the “TP Scan”option, press [Exit] key to
exit the scan and save the current
parameters.
Single Scan
1 Press [Red] key to show an option asking
you: Scan Mode (select if you want to scan
all channels or only Free To Air channels),
Programme Type (select if you want to
scan all channels or only scan TV/Radio
channels), Scan Type (select if you want to
scan the existing TP), Automatic Scan
means blind scan (no existing TP info is
required) and NIT Search On/Off. After you
set these press [OK] key to start scanning.
2 Press [White] key to start the blind scan
immediately.
TP Scan
Press [Green] key to scan current TP’s
programmes.
Auto DiSEqC
Press [Blue] key to run Auto DiSEqC function, it
can find the satellites connected to each port
automatically.

19
Blind Scan
Press [White] key to enter blind scan mode
directly to scan the current satellite.
10.2 Auto installation
“Auto Installation” is a very new and convenient
function. It will automatically detect all dishes
connected to this receiver and scan the
available services of the satellite(S) matched
using the satellites and transponder data in
current database. You don’t have to input any
parameters of your antenna settings. Just press
“OK” button to enter this “Auto Installation”
menu, it starts scanning and shows you the
result at the end of scan.
10.3 Satellite Guide
When you enter “Satellite Guide”menu, you will
see the screen like below:
“Satellite Guide”is for user to enter local
longitude; local latitude and satellite longitude.
The receiver evaluates the antenna azimuth and
antenna elevation; user can follow this guidance
to adjust antenna if required.
1 You can use number keys to input
parameters in “Local Longitude”, “Local
Latitude”and “Satellite Longitude”.
2 You can use [Left/Right] key to select east
or west in “Local Longitude”and “Satellite
Longitude”, select north and south in
“Local Latitude”.
3 Move highlight to “Start”item and press
[OK] key. The lower column on the screen
will calculate the corresponding value
automatically.
4 Orientation means the angle between
south and satellite.
5 Press [Exit] key to draw back to “Main”
Menu.
10.4 Terrestrial Installation
Press [OK] key to enter the selected item.
1 You can select the Region according to
your country.
2 You can set the Tuner Power ON/OFF.
3 Press [Red] key to enter blind scan mode to
scan the current programmes.

20
4 Press [Green] key to enter the following
menu.
Scan Mode.
1 There is two modes. You can scan channels
“By Channel”or “By Frequency”.
2 When scan band is UHF and region is
“France”, the range of Ch No. is from 21 to
69. When scan band is VHF and region is
“France”, the range of Ch No. is from 1 to 9.
(It’s according to region)
3 Press [Red] key to enter blind scan menu, or
press [Green] key to enter TP scan menu.
4 Press [Exit] key to exit the scan.
10.5 Cable Installation
Press [OK] key to enter the selected item.
You can select the Scan Mode, Manual
Scan or Blind Scan.
You can input the Frequency by using
the numeric buttons of the RCU.
If you set the Scan Mode to Blind Scan
you can input the Second Frequency
by using the numeric buttons of the
RCU.
You can input the Symbol Rate by use
the numeric button of the RCU.
You can select the QAM value from
16QAM, 32QAM, 64QAM, 128QAM
and 256QAM.
If you set the Scan Mode to Manual
Scan you can turn ON or OFF the NIT
Search.
When you complete your changes,
press OK button on Search to enter
Scan menu and then press OK button
to begin scan.
11. Preference
When you enter the “Preference”menu, you will
see a screen like below:
In “Preference”menu:
Press [Channel Up/Channel Down] key to
select menu item: Language, Parental
Lock, Control Time setting, Timer, A/V