Icidu NI-707534 Installation instructions

FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
•Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized
modifications to this equipment. Such modifications could void the user’s authority to operate the
equipment.

FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-located or operating in conjunction with
any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only
Mobile Configurations. The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.”
CE Mark Warning
National restrictions
This device is intended for home and office use in all EU countries (and other countries following
the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:
Country Restriction Reason/remark
Bulgaria None General authorization required for outdoor use and
public service
France
Outdoor use limited to 10
mW e.i.r.p. within the band
2454-2483.5 MHz
Military Radiolocation use. Refarming of the 2.4 GHz
band has been ongoing in recent years to allow current
relaxed regulation. Full implementation planned 2012
Italy None If used outside of own premises, general authorization is
required
Luxembourg None General authorization required for network and service
supply(not for spectrum)
Norway Implemented This subsection does not apply for the geographical area
within a radius of 20 km from the centre of Ny-Ålesund
Russian Federation None Only for indoor applications
Note: Please don’t use the product outdoors in France.

- I -
CONTENTS
Package Contents.....................................................................................................1
Chapter 1. Introduction.........................................................................................2
1.1 Overview of the Router.................................................................................................2
1.2 Conventions..................................................................................................................3
1.3 Main Features...............................................................................................................3
1.4 Panel Layout.................................................................................................................4
1.4.1 The Front Panel ................................................................................................4
1.4.2 The Rear Panel.................................................................................................5
Chapter 2. Connecting the Router.......................................................................6
2.1 System Requirements ..................................................................................................6
2.2 Installation Environment Requirements........................................................................6
2.3 Connecting the Router..................................................................................................6
Chapter 3. Quick Installation Guide.....................................................................8
3.1 TCP/IP Configuration....................................................................................................8
3.2 Quick Installation Guide..............................................................................................10
Chapter 4. Configuring the Router ....................................................................16
4.1 Login ...........................................................................................................................16
4.2 Status ..........................................................................................................................16
4.3 Quick Setup ................................................................................................................18
4.4 WPS............................................................................................................................18
4.5 Network.......................................................................................................................25
4.5.1 LAN .................................................................................................................25
4.5.2 WAN................................................................................................................26
4.5.3 MAC Clone......................................................................................................36
4.6 Wireless ......................................................................................................................37
4.6.1 Wireless Settings ............................................................................................38
4.6.2 Wireless Security ............................................................................................40
4.6.3 Wireless MAC Filtering ...................................................................................43
4.6.4 Wireless Advanced .........................................................................................46
4.6.5 Wireless Statistics...........................................................................................47
4.7 DHCP..........................................................................................................................48
4.7.1 DHCP Settings................................................................................................48

- II -
4.7.2 DHCP Clients List ...........................................................................................49
4.7.3 Address Reservation ......................................................................................50
4.8 Forwarding..................................................................................................................51
4.8.1 Virtual Servers ................................................................................................51
4.8.2 Port Triggering ................................................................................................53
4.8.3 DMZ ................................................................................................................55
4.8.4 UPnP...............................................................................................................55
4.9 Security .......................................................................................................................56
4.9.1 Basic Security .................................................................................................56
4.9.2 Advanced Security..........................................................................................58
4.9.3 Local Management .........................................................................................59
4.9.4 Remote Management .....................................................................................60
4.10 Parental Control..........................................................................................................61
4.11 Access Control............................................................................................................64
4.11.1 Rule.................................................................................................................64
4.11.2 Host.................................................................................................................67
4.11.3 Target ..............................................................................................................69
4.11.4 Schedule .........................................................................................................71
4.12 Advanced Routing ......................................................................................................73
4.12.1 Static Routing..................................................................................................73
4.12.2 System Routing Table.....................................................................................74
4.13 Bandwidth Control ......................................................................................................75
4.13.1 Control Settings ..............................................................................................75
4.13.2 Rules List ........................................................................................................75
4.14 IP & MAC Binding Setting...........................................................................................77
4.14.1 Binding Settings..............................................................................................77
4.14.2 ARP List ..........................................................................................................79
4.15 Dynamic DNS .............................................................................................................79
4.15.1 Comexe.cn DDNS...........................................................................................80
4.15.2 Dyndns.org DDNS ..........................................................................................81
4.15.3 No-ip.com DDNS ............................................................................................81
4.16 System Tools...............................................................................................................82
4.16.1 Time Settings ..................................................................................................83
4.16.2 Diagnostic .......................................................................................................84
4.16.3 Firmware Upgrade ..........................................................................................85
4.16.4 Factory Defaults..............................................................................................86

- III -
4.16.5 Backup & Restore...........................................................................................87
4.16.6 Reboot.............................................................................................................88
4.16.7 Password ........................................................................................................88
4.16.8 System Log .....................................................................................................89
4.16.9 Statistics..........................................................................................................91
Appendix A: FAQ....................................................................................................93
Appendix B: Configuring the PC...........................................................................98
Appendix C: Specifications.................................................................................102
Appendix D: Glossary..........................................................................................103

NI-707534
Wireless Router 300N
- 1 -
Package Contents
The following items should be found in your package:
NI-707534 Wireless Router 300N
Power adapter 9V 0.6A
CD with manuals
Manual
Note:
Make sure that the package contains the above items. If any of the listed items are damaged or
missing, please contact with your distributor.

NI-707534
Wireless Router 300N
- 2 -
Chapter 1. Introduction
Thank you for choosing the NI-707534 Wireless 300N Router.
1.1 Overview of the Router
The NI-707534 Wireless 300N Router integrates 4-port Switch, Firewall, NAT-Router and Wireless
AP. Powered by 2x2 MIMO technology, the Wireless 300N Router delivers exceptional range and
speed, which can fully meet the need of Small Office/Home Office (SOHO) networks and the users
demanding higher networking performance.
The NI-707534 Wireless 300N Router provides up to 300Mbps wireless connection with other
802.11n wireless clients. The incredible speed makes it ideal for handling multiple data streams at the
same time, which ensures your network stable and smooth. The performance of this 802.11n wireless
Router will give you the unexpected networking experience at speed 650% faster than 802.11g. It is
also compatible with all IEEE 802.11g and IEEE 802.11b products.
With multiple protection measures, including SSID broadcast control and wireless LAN
64/128/152-bit WEP encryption, WiFi protected Access (WPA2- PSK, WPA- PSK), as well as
advanced Firewall protections, the NI-707534 Wireless 300N Router provides complete data
privacy.
The NI-707534 Wireless 300N Router provides flexible access control, so that parents or network
administrators can establish restricted access policies for children or staff. It also supports Virtual
Server and DMZ host for Port Triggering, and then the network administrators can manage and
monitor the network in real time with the remote management function.
Since the Router is compatible with virtually all the major operating systems, it is very easy to
manage. Quick Setup Wizard is supported and detailed instructions are provided step by step in
this user guide. Before installing the Router, please look through this guide to know all the
Router’s functions.
Simple Installation
Flexible Access Control
Multiple Security Protections
Incredible Speed

NI-707534
Wireless Router 300N
- 3 -
1.2 Conventions
The Router or NI-707534 mentioned in this guide stands for NI-707534 Wireless 300N Router without
any explanation.
1.3 Main Features
Complies with IEEE 802.11n to provide a wireless data rate of up to 300Mbps.
One 10/100M Auto-Negotiation RJ45 WAN port, four 10/100M Auto-Negotiation RJ45 LAN
ports, supporting Auto MDI/MDIX.
Provides WPA/WPA2, WPA-PSK/WPA2-PSK authentication, TKIP/AES encryption security.
Shares data and Internet access for users, supporting Dynamic IP/Static IP/PPPoE Internet
access.
Supports Virtual Server, Special Application and DMZ host.
Supports UPnP, Dynamic DNS, Static Routing.
Provides Automatic-connection and Scheduled Connection on certain time to the Internet
Built-in NAT and DHCP server supporting static IP address distributing.
Supports Parental Control and Access Control.
Connects Internet on demand and disconnects from the Internet when idle for PPPoE.
Provides 64/128/152-bit WEP encryption security and wireless LAN ACL (Access Control
List).
Supports Flow Statistics.
Supports firmware upgrade and Web management.

NI-707534
Wireless Router 300N
- 4 -
1.4 Panel Layout
1.4.1 The Front Panel
Figure 1-1 Front Panel sketch
The Router’s LEDs and the WPS/Reset button are located on the front panel
(View from left to right).
Name Status Indication
PWR Off Power is off.
On Power is on.
SYS Flashing The Router is working properly.
On /Off The Router has a system error.
WLAN Off The Wireless function is disabled.
Flashing The Wireless function is enabled.
WAN,
LAN 1-4
Off There is no device linked to the corresponding port.
On
There is a device linked to the corresponding port but
there is no activity.
Flashing There is an active device linked to the corresponding port.
WPS
Slow Flash A wireless device is connecting to the network by WPS
function. This process will last in the first 2 minutes.
On A wireless device has been
successfully added to the
network by WPS function.
Quick Flash A wireless device failed to be added
to the network by
WPS function.
Table 1-1 The LEDs Description
Note:
1. After a device is successfully added to the network by WPS function, the WPS LED will keep
on for about 5 minutes and then turn off.
2. When press and hold the WPS/Reset button for more than 5 seconds, you will reset the
router.

NI-707534
Wireless Router 300N
- 5 -
1.4.2 The Rear Panel
Figure 1-2 Rear Panel sketch
The following parts are located on the rear panel (View from left to right).
POWER: The Power socket is where you will connect the power adapter. Please use the
power adapter provided with this NI-707534 Wireless 300N Router.
ON/OFF: The switch for the power.
WAN:This WAN port is where you will connect the DSL/cable Modem, or Ethernet.
4,3,2,1 (LAN): These ports (4,3,2,1) connect the Router to the local PC(s).
Wireless antenna: To receive and transmit the wireless data.

NI-707534
Wireless Router 300N
- 6 -
Chapter 2. Connecting the Router
2.1 System Requirements
Broadband Internet Access Service (DSL/Cable/Ethernet)
One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the Router is
connected directly to the Ethernet.)
PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors
TCP/IP protocol on each PC
Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari
2.2 Installation Environment Requirements
Place the Router in a well ventilated place far from any heater or heating vent
Avoid direct irradiation of any strong light (such as sunlight)
Keep at least 2 inches (5 cm) of clear space around the Router
Operating Temperature: 0℃~40℃ (32℉~104℉)
Operating Humidity: 10%~90%RH, Non-condensing
2.3 Connecting the Router
Before installing the Router, make sure your PC is connected to the Internet through the
broadband service successfully. If there is any problem, please contact your ISP. After that, please
install the Router according to the following steps. Don't forget to pull out the power plug and keep
your hands dry.
1. Power off your PC, Cable/DSL Modem, and the Router.
2. Locate an optimum location for the Router. The best place is usually at the center of your
wireless network.
3. Adjust the direction of the antenna. Normally, upright is a good direction.
4. Connect the PC(s) and each Switch/Hub in your LAN to the LAN Ports on the Router, shown
in Figure 2-1. (If you have the wireless NIC and want to use the wireless function, you can
skip this step.)
5. Connect the DSL/Cable Modem to the WAN port on the Router, shown in Figure 2-1.

NI-707534
Wireless Router 300N
- 7 -
6. Connect the power adapter to the power socket on the Router, and the other end into an
electrical outlet. Press the power switch, then the Router will start to work automatically.
7. Power on your PC and Cable/DSL Modem.
Figure 2-1 Hardware Installation of the NI-707534 Wireless 300N Router

NI-707534
Wireless Router 300N
- 8 -
Chapter 3. Quick Installation Guide
This chapter will show you how to configure the basic functions of your NI-707534 Wireless 300N
Router using Quick Setup Wizard within minutes.
3.1 TCP/IP Configuration
The default IP address of the NI-707534 Wireless 300N Router is 192.168.1.1. And the default
Subnet Mask is 255.255.255.0. These values can be changed as you desire. In this guide, we use
all the default values for description.
Connect the local PC to the LAN ports of the Router. And then you can configure the IP address
for your PC in the following two ways.
Configure the IP address manually
1) Set up the TCP/IP Protocol for your PC. If you need instructions as to how to do this,
please refer to Appendix B: "Configuring the PC".
2) Configure the network parameters. The IP address is 192.168.1.xxx ("xxx" is any number
from 2 to 254), Subnet Mask is 255.255.255.0, and Gateway is 192.168.1.1 (The
Router's default IP address)
Obtain an IP address automatically
1) Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC.
If you need instructions as to how to do this, please refer to Appendix B: "Configuring the
PC”.
2) Then the built-in DHCP server will assign IP address for the PC.
Now, you can run the Ping command in the command prompt to verify the network connection
between your PC and the Router. The following example is in Windows 2000 OS.
Open a command prompt, and type ping 192.168.1.1, and then press Enter.
If the result displayed is similar to the Figure 3-1, it means the connection between your PC
and the Router has been established well.

NI-707534
Wireless Router 300N
- 9 -
Figure 3-1 Success result of Ping command
If the result displayed is similar to the Figure 3-2, it means the connection between your PC
and the Router is failed.
Figure 3-2 Failure result of Ping command
Please check the connection following these steps:
1. Is the connection between your PC and the Router correct?

NI-707534
Wireless Router 300N
- 10 -
Note:
The 1/2/3/4 LEDs of LAN ports which you link to on the Router and LEDs on your PC's adapter
should be lit.
2. Is the TCP/IP configuration for your PC correct?
Note:
If the Router's IP address is 192.168.1.1, your PC's IP address must be within the range of
192.168.1.2 ~ 192.168.1.254.
3.2 Quick Installation Guide
With a Web-based utility, it is easy to configure and manage the NI-707534 Wireless 300N Router.
The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser,
such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
1. To access the configuration utility, open a web-browser and type in the default address
192.168.1.1 in the address field of the browser.
Figure 3-3 Log in the Router
After a moment, a login window will appear, similar to the Figure 3-4. Enter admin for the
User Name and Password, both in lower case letters. Then click the OK button or press the
Enter ke y.
Figure 3-4 Login Windows

NI-707534
Wireless Router 300N
- 11 -
Note:
If the above screen does not pop-up, it means that your Web-browser has been set to a proxy.
Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears,
cancel the Using Proxy checkbox, and click OK to finish it.
2. After successfully log in, you can click the Quick Setup menu to quickly configure your
Router.
Figure 3-5 Quick Setup
3. Click Next, and then WAN Connection Type page will appear, shown in Figure 3-6.
Figure 3-6 WAN Connection Type
The Router provides Auto-Detect function and supports three popular ways PPPoE,
Dynamic IP and Static IP to connect to the Internet. It’s recommended that you make use of
the Auto-Detect function. If you are sure of what kind of connection type your ISP provides,
you can select the very type and click Next to go on configuring.
4. If you select Auto-Detect, the Router will automatically detect the connection type your ISP
provides. Make sure the cable is securely plugged into the WAN port before detection. The
appropriate configuration page will be displayed when an active Internet service is
successfully detected by the Router.

NI-707534
Wireless Router 300N
- 12 -
1) If the connection type detected is PPPoE, the next screen will appear as shown in Figure
3-7.
Figure 3-7 Quick Setup - PPPoE
User Name/Password - Enter the User Name and Password provided by your ISP.
These fields are case sensitive. If you have difficulty with this process, please contact your
ISP.
2) If the connection type detected is Dynamic IP, the next screen will appear as shown in
Figure 3-9. Then you can go on with the wireless configuration.
3) If the connection type detected is Static IP, the next screen will appear as shown in Figure
3-8.
Figure 3-8 Quick Setup - Static IP
IP Address - This is the WAN IP address as seen by external users on the Internet
(including your ISP). Enter the IP address into the field.
Subnet Mask - The Subnet Mask is used for the WAN IP address, it is usually
255.255.255.0.
Default Gateway - Enter the gateway IP address into the box if required.

NI-707534
Wireless Router 300N
- 13 -
Primary DNS - Enter the DNS Server IP address into the box if required.
Secondary DNS - If your ISP provides another DNS server, enter it into this field.
5. Click Next to continue, the Wireless settings page will appear as shown in Figure 3-9.
Figure 3-9 Quick Setup – Wireless
Wireless Radio - Enable or disable the wireless radio choosing from the drop-down list.
SSID - Enter a value of up to 32 characters. The same name of SSID (Service Set
Identification) must be assigned to all wireless devices in your network. Considering
your wireless network security, the default SSID is set to be ICIDU. This value is
case-sensitive. For example, TEST is NOT the same as test.
Region -Select your region from the drop-down list. This field specifies the region
where the wireless function of the Router can be used. It may be illegal to use the
wireless function of the Router in a region other than one of those specified in this field.
If your country or region is not listed, please contact your local government agency for
assistance.
Note:
Limited by local law regulations, version for North America does not have region
selection option.
Channel - This field determines which operating frequency will be used. The default
channel is set to Auto, so the AP will choose the best channel automatically. It is not