ICON EDGE User manual

EDGE
USER MANUAL
KEEP THIS MANUAL FOR FUTURE NEEDS

ICON EDGE USER MANUAL 1
CONTENTS
1. SAFETY INSTRUCTIONS 2
2. FEATURES 4
3. FIXTURE OVERVIEW 6
4. DIMENSIONAL DRAWINGS 7
5. INSTALLATION INSTRUCTIONS 8
6. DMX-512 CONTROL CONNECTION 17
7. DMX-512 CONNECTION WITH DMX TERMINATOR 17
8. DEVICE DMX START ADDRESS SELECTION 18
9. DISPLAY 18
10. DMX PROTOCOL 26
11. ERROR MESSAGES 31
12. CLEANING AND MAINTENANCE 33

ICON EDGE USER MANUAL 2
1. SAFETY INSTRUCTIONS
1.1. IMPORTANT SAFETY WARNING
This device has left the factory in perfect condition. In order to maintain this condition and to ensure safe
operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written
in this user manual.
In order to install, operate, and maintain the lighting fixture safely and correctly we suggest that the
installation and operation be carried out by qualified technicians and these instructions be carefully
followed.
CAUTION!
HIGH VOLTAGE. RISK OF SEVERE OR FATAL ELECTRIC SHOCK
CAUTION!
ALWAYS DISCONNECT MAINS SUPPLY BEFORE REMOVING ANY FIXTURE COVERS
CAUTION!
NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE. SENSITIVE PERSONS MAY SUFFER
AN EPILEPTIC SHOCK
CAUTION!
NEVER TOUCH THE DEVICE DURING OPERATION! COVERS MAY BE HOT
CAUTION!
KEEP THIS DEVICE AWAY FROM RAIN AND MOISTURE
Important:
Damage caused by the disregard of this user manual is not subject to warranty. The dealer
and manufacturer will not accept liability for any resulting defects or problems.
1) If the device has been exposed to temperature changes due to environmental conditions, do not
power on immediately. The resulting condensation could damage the device. Leave the device
powered off until it has reached room temperature.
2) This device falls under protection-class I. Therefore, it is essential that the device be earthed.
3) If either lenses or display are damaged (damage may include cracks or gashes in the material)
they must be replaced.
4) Electrical connections, such as replacing the power plug, must be performed by a qualified person.
5) Make sure that the available voltage is not higher than that which is stated at the end of this
manual.
6) Make sure the power cord is never crushed or damaged by sharp edges. If the flexible power cord
of this device is damaged, it should be replaced by the manufacturer, local service agent or a
similar qualified person in order to avoid injury.
7) When the device is not in use or before performing maintenance, always disconnect the device
from the mains. Only handle the power cord from the plug. Never pull the plug out of a socket by
tugging the power cord.
8) When powered on for the first time, some smoke or smell may occur. This is caused by coating on
metal parts when heated and is normal. If you are concerned, please contact your distributor.
9) Do not focus the beam onto flammable surfaces. The minimum distance between the exiting lens
of the device and the illuminated surface must be greater than 10 metres.

ICON EDGE USER MANUAL 3
Please be aware that damage caused by any modifications to the device are not subject to warranty.
Keep away from children and non-professionals.
1.2. GENERAL GUIDELINES
1) This device is a lighting effect for professional use on stages, in discotheques, theatres, etc., the
device was designed for indoor use only.
2) This fixture is only allowed to be operated within the maximum alternating current as stated in the
technical specifications in section 2 of this manual.
3) Handle the device with care, avoid shaking or using force when installing or maintaining the device.
4) When choosing the installation location, please make sure that the device is not exposed to
extreme heat, moisture or dust.
5) If you use the quick lock cam when rigging the device, make sure the quick lock fasteners are
located in the quick lock holes correctly and securely.
6) Operate the device only after having familiarised yourself with its functions. Do not permit operation
by persons not qualified for operating the device. Most damages are the result of unprofessional
operation.
7) Please use the original packaging if the device is to be transported.
8) The applicable temperature for the device is between -10°C to 45°C. Do not use the device outside
of this temperature range.
For safety reasons, please be aware that all modifications to the device are forbidden.
If this device is operated in any way different to the ones described in this manual, the product may
suffer damage and the warranty becomes void. Furthermore, any other operation may lead to
short-circuits, burns, electric shocks etc.

ICON EDGE USER MANUAL 4
2. FEATURES
POWER SUPPLY
 AC 100-240V~，50/60Hz
 Power Consumption: 700W
OPTICS

Lamp: MSD Platinum 21R 470W

Extremely long Life: >1500H
MOVEMENT
 Pan movement: 540。 /630。 Optional (16 bit)
 Tilt movement: 270。 (16 bit)

Advanced moving system: fast, stable and quite, auto x-y repositioning
COLORS

CMY & CTO Variable Color Mixing for Infinite Color Possibilities

1 Color wheel: 14 dichroic filters + open, indexable, rainbow effect
GOBOS
 1 Rotation gobo wheel: 8 interchangeable, rotating, and indexable, gobo + open
 “Slot in & out” gobo wheel system.
 1 Static gobo wheel: 14 + open
FEATURES

2 Control channel modes: 25/36 channels

2 operations modes: DMX-512, Extended / Standard
 Strobe effect with 1-25 flashes per second and pulse effect
 Rotating Prism: 8 facets prism, Linear prism and prism Macros
 Motorized focus
 Dimmer: 0%~100% full range dimming.
 Stepless frost, 0%~100% linear change frost.

Animation Wheel: flame or water effect
DISPLAY
 Advanced and convenient full –color LCD touch screen, with rechargeable battery
 Locked automatically after standby for 15 seconds to prevent error; hold the button for 3
seconds to activate.
 Pan/Tilt Lock Out：Locks Pan / Tilt from resetting, enabling reset to be carried out inside a flight case.
Power the unit. Press & hold button until the display shows “No Movement Reset”.
SOFTWARE
Upgrades: fast and convenient through DMX cable
Reset DMX address, remote lamp switch, reset can all be done by the controller
Running time of fixture on display for reference
OTHER SPEC
Input signal isolation: guarantees stable signal transmission without interference
Advanced RDM function
WE
IGHT
Net weight: 29.8 kg

ICON EDGE USER MANUAL 5
DMX CHANNEL DATA IMAGE

ICON EDGE USER MANUAL 6
3. FIXTURE OVERVIEW
1） Lens
2） Display
3） Mode/Esc-button
4） Left-button
5） Down-button
6） ENTER-button
7） Right-button
8） Up-button
9） RJ45 in
10） RJ45 out
11） DMX in
12） DMX out
13） Power in
14） Power out
15） Fuse

ICON EDGE USER MANUAL 7
4. DIMENSIONAL DRAWINGS

ICON EDGE USER MANUAL 8
5. INSTALLATION INSTRUCTIONS
5.1. Installing or replacing the lamp
CAUTION!
ONLY INSTALL THE LAMP WITH THE DEVICE UNPLUGGED FROM THE MAINS
CAUTION!
THE LAMP HAS TO BE REPLACED WHEN IT IS DAMAGED OR DEFORMED
Because of the nature of the extreme heat associated with the MSD Platinum 21R
470W lamp and the tight nature of the internal optical system it is imperative that
the lamp be replaced every 1500 hours. This is done to protect the internal optical
system as well as prevent accidental lamp explosion, which could lead to hot glass
particles falling from the fixture. Failure to change the lamp within 300 hours of
operation will result in automatic shut down of the fixture’s electronics.
At 1500 hours the display will begin to flash “Replace the lamp” and the lamp will
flicker for the first five minutes of operation. At this point the lamp has reached the
maximum rated life and should be replaced immediately. After the lamp has
flickered for about five minutes it should strike normally allowing the fixture to be
used temporarily until a replacement lamp can be installed. The fixture will
continue to operate for an additional 300 hours, however the “Replace the Lamp”
warning will continue to flash in the display. Keep in mind that the flicker protection
circuitry will only work for about 300 hours (lamp clock life of 1500-1800 hours).
After 1800 hours the fixture will no longer respond to DMX commands and
immediately enter a hibernation mode that will electronically discontinue all fixture
functionality with the exception of a few menu commands. The fixture will continue
to enter hibernation mode until the lamp is replaced and the lamp clock has been
reset.
Before replacing the lamp let the lamp cool down, because during operation, the lamp can
reach very high temperatures.
During the installation of halogen lamps do not touch the glass bare handed. Always use a cloth to handle
the lamps during insertion and removal.
Do not install lamps with a higher wattage. They generate higher temperatures than which the device was
designed for.
WARNING!
THE BULB SHOULD BE REPLACED WHEN DAMAGED OR HEAT DISTORTION.
CAUTION!
DISCONNECT THE FIXTURE FROM POWER AND ALLOW IT TO COOL FOR ONE HOUR

ICON EDGE USER MANUAL 9
Procedures:
1) Please put the fixture on a flat surface, release the screw A, B, C, D. Then open the back plate to
view the lamp-socket.
2) Before removing the lamp, please release the lamp wires which connect to the lamp terminals.
3) Release the screw indicated by arrow below, pull the metal plate to the right, and then pull down
the spring, whilst holding the lamp to ensure it doesn’t fall out.
4) Ensure to use a soft cloth to remove and replace the lamp to avoid your fingers touching the
glass of the lamp.
5) Replace lamp and make it stable and located. Please note that there's only one orientation for
the lamp. Make sure the replaced lamp is installed in the same direction as the old with the
terminals of the lamp pointing down.
6) Replace the spring over the lamp and re-install the plate over the spring. Tighten screw and
replace lamp wires.
7) Replace the back plate and tighten screw A, B, C, D.
8) Please reset the lamp life-time. Otherwise it is likely to trigger the protecting firmware of the
system to make the replaced lamp close itself automatically.

ICON EDGE USER MANUAL 10
Please remember the lamp is not a hot-restrike type, you must wait for
approximately 10
minutes after having turned off the lamp before you can turn it back on again.
CAUTION!
DO NOT OPERATE THIS DEVICE WITH OPEN COVERS
5.2. RIGGING THE DEVICE
CAUTION!
PLEASE CONSIDER THE GB7000.1-2015, GB7000.217-2008 AND THE OTHER
RESPECTIVE NATIONAL NORMS DURING THE INSTALLATION. THE INSTALLATION
MUST ONLY BE CARRIED OUT BY A QUALIFIED PERSON.
 The structure on which the device is rigged must be able to support 10 times the weight of the
device for 1 hour without any critical deformation occurring.
 The installation must always be secured with a secondary safety attachment, e.g. the included
appropriate safety cable.
 Never stand directly below the device when rigging, de-rigging or maintaining the device.
 All electrical connections should be approved by a qualified electrician prior to using the product.
 When the device is permanently installed these installations have to be approved by a qualified
person once a year.
 Overhead rigging requires extensive experience, including (but not limited to) calculating working
load limits, specifying installation/ rigging materials, and periodic safety inspection of all installation
material as well as the device. If you lack these qualifications, do not attempt the rigging of this
device yourself. Improper installation/ rigging can result in serious bodily injury.
 Before rigging, make sure that the installation area can hold a minimum point load of 10 times the
device’s weight.

ICON EDGE USER MANUAL 11
5.3. RIGGING USING THE OMEGA BRACKETS
 Fix the clamp to the bracket by tightening the M12 nut and bolt to the bracket through the Ф13 hole
in the middle of the bracket.
 Insert the quick-lock fasteners of the first Omega holder into the respective holes on the bottom of
the device. Tighten the quick-lock fasteners fully clockwise.
 Install the second Omega holder.
 Pull the safety cable through the holes on the bottom of the base and over the trussing system or
another suitable rigging point. Insert the end into the carabiner and tighten the safety screw.
Important:
This step is very important to ensure safe rigging of the fixture.

ICON EDGE USER MANUAL 12
5.4. RIGGING DRAWINGS
 The device can be rigged in any of the orientations shown in the image above.
 The device must be kept at least 0.1 m away from any flammable materials (decoration etc.).
 Always use and install the supplied safety cable as a safety measure to prevent accidental damage
and/or injury in the event the clamp fails.
Important:
Overhead rigging requires extensive experience, including (but not limited to) calculating
working load limits, specifying installation/ rigging materials, and periodic safety inspection of all
installation material as well as the device. If you lack these qualifications, do not attempt the
rigging of this device yourself. Improper installation/ rigging can result in serious bodily injury.

ICON EDGE USER MANUAL 13
5.5. CMY Module and Pattern Module Disassembly and Installation
CMY Module Disassemble and Install Instruction：
Disassemble 1: Remove 4 screws: A, B, C, D. Remove the 2 positioning plates: E,F. Unplug the
sensor signal wire from socket G.
Install 4 or 7: rotate the yoke 180, flip the head to another side, and use screw A, B to lock
positioning plate E tightly and screw C, D to lock positioning plate F tightly. Plug the sensor signal
wire into socket G.
Disassemble 2: rotate the yoke 180, flip the head to the other side, and remove 2 screws: H, I.
Install 3 or 6: Positioning the CMY module to the right place, lock 2 screws: H, I.
Disassemble 3: Pull out the CMY module about 30mm, unplug power cord from socket J and
signal wire from K.
Install 2 or 5: Push along the CMY module into the slot about 90mm, plug the power cord into
socket J and signal wire into socket K.

ICON EDGE USER MANUAL 14
Disassemble 4: Pull out CMY module L until this bulkhead is separated from the fixture. This is
all for the disassembling CMY module.
Install 1 or 4: Push along the CMY module L into the slot steadily.
Installation of CMY module is the backward procedure from 1-4.

ICON EDGE USER MANUAL 15
Pattern Module Disassemble and Install Instruction：
With the limitation of the space, the CMY module has to be removed before disassemble the pattern
and color module. Ensure the Zoom Assy is pushed forward to the front lens.
Disassemble 5: Remove 2 screws: M, N
Install 3: Push the gobo into the right place and lock 2 screws M, N.
Disassemble 6: Pull out the gobo assembly about 60mm, unplug the power cord from socket O, and
signal wire from socket P.
Install 2: Push along the gobo assembly into the slot about 50mm, plug the power cord into socket O
and signal wire into socket P.

ICON EDGE USER MANUAL 16
Remove 7: Pull out the gobo & color assembly Q until it’s separated from the fixture. This is all for
the gobo & color assembly disassembling.
Install 1: Push along the gobo & color assembly Q into the socket.
Pattern assembly installation is the backward procedure from 1-3. Last but not the least, install the
CMY module in the end 4-7.

ICON EDGE USER MANUAL 17
6. DMX-512 CONTROL CONNECTION
Connect the provided male side of the XLR cable to the female XLR output of your controller and the
female side of the XLR cable to the male XLR input of the device. You can connect multiple devices
together in a serial fashion. The cable needed should be two core, screened cable with XLR input and
output connectors. Please refer to the diagram below.
Address 1 Address 26 Address 51
7. DMX-512 CONNECTION WITH DMX TERMINATOR
For installations where the DMX cable has to run over a long distance or is in an electrically noisy
environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps in
preventing corruption of the digital control signal caused by electrical noise. The DMX terminator is an XLR
plug with a 120 Ω resistor connected between pins 2 and 3, which is then plugged into the output (female)
XLR socket of the last fixture in the chain. Please see illustrations below.

ICON EDGE USER MANUAL 18
8. DEVICE DMX START ADDRESS SELECTION
All fixtures should be given a DMX starting address when using a DMX signal, so that the correct fixture
responds to the correct control signals. This digital starting address is the channel number from which the
fixture starts to “listen” to the digital control information sent out from the DMX controller. The allocation of
this starting address is achieved by setting the correct address number on the display located on the base
of the device.
You can set the same starting address for all fixtures or a group of fixtures, or set different addresses for
each fixture individually.
If you set the same address on all devices, all the devices will start to “listen” to the same control signal
from the same channel number. In other words, changing the settings of one channel will affect all the
fixtures simultaneously.
If you set a different address, each unit will start to “listen” to the channel number you have set, based on
the quantity of control channels of the unit. That means changing the settings of one channel will affect only
the selected device.
In the case of the led move head, which is a 25 channel fixture, you should set the starting address of the
first unit to 1, the second unit to 26 (25 + 1), the third unit to 51 (25+ 26), and so on.
9. DISPLAY
The Display offers several features: you can set the starting address, run the pre-programmed
program or reset the device.
The main menu is accessed by pressing the -button until the display starts flashing. Browse
through the menu by pressing the -button, -button, -button or -button.
Press the Enter-button in order to select the desired menu. You can change the selection by
pressing the -button, -button, -button or -button. Confirm every selection
by pressing the -button. You can leave every mode by pressing the -button. After
accessing the edit mode, the unit will automatically exit to the main menu after 15 seconds from
the last button press. When the unit is powered on, if no data signal is connected after 1 minute,
then the display will switch off automatically. The Display does not need external power to
operate. Hold down the -button for 3 seconds and the Display will turn on by using the unit’s
battery built in battery.

ICON EDGE USER MANUAL 19
Address A001~AXXX
Config
Mode Extended Mode Default
Standard Mode
Select Signal DMX Only Default
Art-Net On IP2
Art-Net On IP10
Set Universe 001~255 Default 001
Pan and Tilt Tilt Reverse On/Off Default Off
Pan Reverse On/Off Default Off
Feedback On/Off Default On
Dimmer Curve Standard Default
Linear
Beam enable Rot. gobo
ALL GLASS GOBO
ALL METAL GOBO Default
GOBO8 IS GLASS
Reset Defaults On/Off Default Off
Lamp
Lamp Power On/Off Default Off
Automatic On On/Off Default Off
Lamp Hours XXXX (Hours)
Password
Reset Lamp Hour On/Off Need Password 38
Temperature Head Temperature XXX
℃
/
℉
Reset
Function
All
Pan/Tilt
Others
Comm
Read DMX Value Pan, Tilt, ……
DMX Info DMX Update Rate Unit: Package per
second (p/s)
Comm Loss
No Fade on Loss
Fade out 30 seconds Default
Fade out 60 seconds
Info
Software Version V1.1.0……
ARTNET IP ARTNET IP
XXX. XXX. XXX. XXX
XXX. XXX. XXX. XXX
Cross load SW On Need Password 50
Off Default
Total Run Time XXXX (Hours)
Last Run Time XXXX (Hours)