ICON STAGE User manual

STAGE
USER MANUAL
KEEP THIS MANUAL FOR FUTURE NEEDS

ICON STAGE USER MANUAL
1
CONTENTS
1. SAFETY INSTRUCTIONS………………………………………………………………………………… 2
IMPORTANT SAFETY WARNING………………………………………………………………………. 2
GENERAL GUIDELINES ………………………………………………………………………………… 3
2. FEATURES ……………………………………………………………………………….………………….. 4
3. FIXTURE OVERVIEW……………………………………………………………………………………... 6
4. DIMENSIONAL DRAWINGS……………………………………………………………………………… 7
5. INSTALLATION INSTRUCTIONS…………………………………………………………………………. 8
RIGGING THE DEVICE …………………………………………………………………………………... 8
RIGGING USING THE OMEGA BRACKET……………………………………………………………... 9
RIGGING DRAWINGS……………………………………………………………………………………. 10
6. DMX-512 CONTROL CONNECTION…………………………………………………………………… 11
7. DMX-512 CONNECTION WITH DMX TERMINATOR ………………………………………………... 11
8. DEVICE DMX START ADDRESS SELECTION ………………………………………………………. 12
9. DISPLAY ……………………………………………………………………………………………………. 12
Address ……………………………………………………………………………………………………. 15
Config ……………………………………………………………………………………………………… 15
Reset Function ……………………………………………………………………………………………. 17
Communication……………………………………………………………………………………………. 17
Info………………………………………………………………………………………………………….. 18
Test…………………………………………………………………………………………………………. 20
10. DMX PROTOCOL………………………………………………………………………………………….. 21
11. ERROR MESSAGES………………………………………………………………………………………. 27
12. CLEANING AND MAINTENANCE……………………………………………………………………….. 30

ICON STAGE USER MANUAL
2
1. SAFETY INSTRUCTIONS
1.1. IMPORTANT SAFETY WARNING
This device has left the factory in perfect condition. In order to maintain this condition and to ensure safe
operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written
in this user manual.
In order to install, operate, and maintain the lighting fixture safely and correctly we suggest that the
installation and operation be carried out by qualified technicians and these instructions be carefully
followed.
CAUTION!
HIGH VOLTAGE. RISK OF SEVERE OR FATAL ELECTRIC SHOCK
CAUTION!
ALWAYS DISCONNECT MAINS SUPPLY BEFORE REMOVING ANY FIXTURE COVERS
CAUTION!
NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE. SENSITIVE PERSONS MAY SUFFER
AN EPILEPTIC SHOCK
CAUTION!
NEVER TOUCH THE DEVICE DURING OPERATION! COVERS MAY BE HOT
CAUTION!
KEEP THIS DEVICE AWAY FROM RAIN AND MOISTURE
Important:
Damage caused by the disregard of this user manual is not subject to warranty. The dealer
and manufacturer will not accept liability for any resulting defects or problems.
1) If the device has been exposed to temperature changes due to environmental conditions, do
not power on immediately. The resulting condensation could damage the device. Leave the
device powered off until it has reached room temperature.
2) This device falls under protection-class I. Therefore, it is essential that the device be earthed.
3) If either lenses or display are damaged (damage may include cracks or gashes in the material)
they must be replaced.
4) Electrical connections, such as replacing the power plug, must be performed by a qualified
person.
5) Make sure that the available voltage is not higher than that which is stated at the end of this
manual.
6) Make sure the power cord is never crushed or damaged by sharp edges. (If the Power cord
suffers from this case, the cable must be replaced by an authorized dealer.)
7) If the external flexible power cord of this device is damaged, it shall be exclusively replaced by
the manufacturer or their service agent or a similar qualified person in order to avoid injury.
8) When the device is not in use or before performing maintenance, always disconnect the device
from the mains. Only handle the power cord from the plug. Never pull the plug out of a socket
by tugging the power cord.
9) When powered on for the first time, some smoke or smell may occur. This is caused by the
coating on the metal parts when it is heated. And it is normal. If you are concerned, please
contact your distributor.
10) Do not focus the beam onto flammable surfaces. The minimum distance between the exiting

ICON STAGE USER MANUAL
3
lens of the device and the illuminated surface must be greater than 2 meters.
Please be aware that damages caused by any modifications to the device are not subject to
warranty. Keep away from children and non-professionals.
1.2. GENERAL GUIDELINES
1) This device is a lighting effect for professional use on stages, in discotheques, theatres, etc.,
the device is designed for indoor use only.
2) This fixture is only allowed to be operated within the maximum alternating current as stated in
the technical specifications in section 2 of this manual.
3) Handle the device with care, avoid shaking or using force when installing or maintaining the
device.
4) When choosing the installation location, please make sure that the device is not exposed to
extreme heat, moisture or dust.
5) If you use the quick lock cam when rigging the device, make sure the quick lock fasteners are
located in the quick lock holes correctly and securely.
6) Operate the device only after having familiarized yourself with its functions. Do not permit
operation by persons not qualified for operating the device. Most damages are the result of
unprofessional operation.
7) Please use the original packaging if the device is to be transported.
8) The applicable temperature for the device is between -10°C to 45°C. Do not use the device
outside of this temperature range.
9) The light source contained in this luminaire shall only be replaced by the manufacturer or his
service agent or a similar qualified person
For safety reasons, please be aware that all modifications to the device are forbidden. If this device
is operated in any way different to the ones described in this manual, the product may suffer
damage and the warranty becomes void. Furthermore, any other wrong operations may lead to
short-circuits, burns, electric shocks etc.

ICON STAGE USER MANUAL
4
2. FEATURES
1) POWER SUPPLY
+ AC 100-240V~，50/60Hz
+ Power Consumption：600W
2)
OPTICS
+ LED：White 420W LED
+ Extremely long Life：>20,000H
3)
MOVEMENT
+ Pan movement：540。 /630。 Optional (16 bit)
+ Tilt movement：270。 (16 bit)
+ Advanced moving system：fast，stable and quite，auto x-y repositioning
4) COLORS
+ CMY & CTO Variable Color Mixing for Infinite Color Possibilities
+ 1 Color wheel: 7 dichroic filters + open, indexable, rainbow effect
5) GOBOS
+ 1 Rotation gobo wheel：7 interchangeable，rotating，and indexable，gobo + open
+ “Slot in & out” gobo wheel system
+ 1 Static gobo wheel：8 + open
6)
FEATURES
+ 2 Control channel modes：34/58 channels
+ 2 operations modes：DMX-512，Extended / Standard
+ Strobe effect with 1-25 flashes per second and pulse effect
+ Rotating Prism：5 facets prism，Linear prism and prism Macros
+ Animation wheel：can make special dynamic flame or water effect
+ Beam angle：zoom for 8.2。~56。
+ Motorized focus
+ Dimmer：0%~100% full range dimming
+ Stepless frost：0%~100% linear change frost
+ Stepless iris：5%~100% linear change iris，pulse iris effect
7)
DISPLAY
+ Advanced and convenient full –color LCD touch screen, with rechargeable battery
+ Locked automatically after standby for 15 seconds to prevent error；hold the button for 3
seconds to activate
+ Pan/Tilt Lock Out：Locks Pan / Tilt from resetting, enabling reset to be carried out inside a flight
case. Power the unit. Press & hold button until the display shows “No Movement
Reset”.
8)
SOFT
WARE
+ Upgrades：fast and convenient through DMX cable
+ Reset DMX address, remote lamp switch, reset can all be done by the controller

ICON STAGE USER MANUAL
5
+ Running time of fixture on display for reference
9)
OTHER SPEC
+ Input signal isolation: guarantees stable signal transmission without interference
Advanced RDM function
10) WEIGHT
+ Net weight：31 kg
11) PHOTOMETRIC DATA

ICON STAGE USER MANUAL
6
3. FIXTURE OVERVIEW
1） Lens
2） Tilt Lock
3） Display
4） Mode/Esc-button
5） Left-button
6） Down-button
7） ENTER-button
8） Right-button
9） Up-button
10） Pan Lock
11） RJ45 in
12） RJ45 out
13） DMX out
14） DMX in
15） Power in
16） Power out
17） Fuse
18） Handle

ICON STAGE USER MANUAL
7
4. DIMENSIONAL DRAWINGS

ICON STAGE USER MANUAL
8
5. INSTALLATION INSTRUCTIONS
5.1 RIGGING THE DEVICE
CAUTION!
PLEASE CONSIDER THE GB7000.1-2015, GB7000.217-2008 AND THE OTHER
RESPECTIVE NATIONAL NORMS DURING THE INSTALLATION. THE INSTALLATION
MUST ONLY BE CARRIED OUT BY A QUALIFIED PERSON.
+ The structure on which the device is rigged must be able to support 10 times the weight of the
device for 1 hour without any critical deformation occurring.
+ The installation must always be secured with a secondary safety attachment, e.g. the included
appropriate safety cable.
+ Never stand directly below the device when rigging, de-rigging or maintaining the device.
+ All electrical connections should be approved by a qualified electrician prior to using the product.
+ When the device is permanently installed these installations have to be approved by a qualified
person once a year.
+ Overhead rigging requires extensive experience, including (but not limited to) calculating working
load limits, specifying installation/ rigging materials, and periodic safety inspection of all
installation material as well as the device. If you lack these qualifications, do not attempt the
rigging of this device yourself. Improper installation/ rigging can result in serious bodily injury.
+ Before rigging make sure that the installation area can hold a minimum point load of 10 times the
device’s weight.

ICON STAGE USER MANUAL
9
5.2 RIGGING USING THE OMEGA BRACKETS
1) Fix the clamp to the bracket by tightening the M12 nut and bolt to the bracket through the Ф13 hole
in the middle of the bracket.
2) Insert the quick-lock fasteners of the first Omega holder into the respective holes on the bottom of
the device. Tighten the quick-lock fasteners fully clockwise.
3) Install the second Omega holder.
4) Pull the safety cable through the holes on the bottom of the base and over the trussing system or
another suitable rigging point. Insert the end into the carabiner and tighten the safety screw.
Important:
This step is very important to ensure safe rigging of the fixture.

ICON STAGE USER MANUAL
10
5.3 RIGGING DRAWINGS
1) The device can be rigged in any of the orientations shown in the image above.
2) The device must be kept at least 0.1 m away from any flammable materials (decoration etc.).
3) Always use and install the supplied safety cable as a safety measure to prevent accidental
damage and/or injury in the event the clamp fails.
Important:
Overhead rigging requires extensive experience, including (but not limited to) calculating
working load limits, specifying installation/ rigging materials, and periodic safety inspection of all
installation material as well as the device. If you lack these qualifications, do not attempt the
rigging of this device yourself. Improper installation/ rigging can result in serious bodily injury.

ICON STAGE USER MANUAL
11
6. DMX-512 CONTROL CONNECTION
Connect the provided male side of the XLR cable to the female XLR output of your controller and the
female side of the XLR cable to the male XLR input of the device. You can connect multiple devices
together in a serial fashion. The cable needed should be two core, screened cable with XLR input and
output connectors. Please refer to the diagram below.
Address 69 Address 35 Address 1
7. DMX-512 CONNECTION WITH DMX TERMINATOR
For installations where the DMX cable has to run over a long distance or is in an electrically noisy
environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps in
preventing corruption of the digital control signal caused by electrical noise. The DMX terminator is an XLR
plug with a 120 Ω resistor connected between pins 2 and 3, which is then plugged into the output (female)
XLR socket of the last fixture in the chain. Please see illustrations below.

ICON STAGE USER MANUAL
12
8. DEVICE DMX START ADDRESS SELECTION
All fixtures should be given a DMX starting address when using a DMX signal, so that the correct fixture
responds to the correct control signals. This digital starting address is the channel number from which the
fixture starts to “listen” to the digital control information sent out from the DMX controller. The allocation of
this starting address is achieved by setting the correct address number on the display located on the base
of the device.
You can set the same starting address for all fixtures or a group of fixtures, or set different addresses for
each fixture individually.
If you set the same address on all devices, all the devices will start to “listen” to the same control signal
from the same channel number. In other words, changing the settings of one channel will affect all the
fixtures simultaneously.
If you set a different address, each unit will start to “listen” to the channel number you have set, based on
the quantity of control channels of the unit. That means changing the settings of one channel will affect only
the selected device.
In the case of the led move head, which is a 34 channel fixture, you should set the starting address of the
first unit to 1, the second unit to 35(34 + 1), the third unit to 69 (34+ 35), and so on.
9. DISPLAY
The Display offers several features: you can set the starting address, run the pre-programmed program or
reset the device.
The main menu is accessed by pressing the -button until the display starts flashing. Browse through
the menu by pressing the -button , -button , -button or -button. Press the
Enter-button in order to select the desired menu. You can change the selection by pressing the
-button , -button , -button or -button. Confirm every selection by pressing the
-button. You can leave every mode by pressing the -button. After accessing the edit mode, the unit will
automatically exit to the main menu after 15 seconds from the last button press. When the unit is powered
on, if no data signal is connected after 1 minute, then the display will switch off automatically. The Display
does not need external power to operate. Hold down the -button for 3 seconds and the Display will be
turned on by the built-in battery.

ICON STAGE USER MANUAL
13
Address A001~AXXX
Config
Mode Extended Mode Default
Standard Mode
Select Signal
DMX Only Default
Art-Net On IP2
Art-Net On IP10
sACN
Set Universe 0000~32767 Default 001
Pan and Tilt Tilt Reverse On/Off Default Off
Pan Reverse On/Off Default Off
Feedback On/Off Default On
Dimmer Mode
Standard Default (Use this
function ,
Please set the
Dim Modes
channel value to
100%.)
Stage
TV
Architectural
Theatre
Refresh 900~25000Hz Default 1200Hz
Gamma 2.0~2.8 Default 2.0
Fan Mode
Auto Default
High
Silent
Gobo Scroll On/Off Default Off
Reset Factory Defaults On/Off Default Off
Reset
Function
All
Pan/Tilt
Others
Communi
cation
Read DMX Value ALL, Control, Pan, Tilt, ……
DMX Info DMX Update Rate
XXXX p/s
(Package per
second)
Comm Loss
No Fade on Loss
Fade out 30 seconds Default
Fade out 60 seconds
Info
Software Version X.X.X……
ARTNET IP ARTNET IP
XXX. XXX. XXX. XXX
XXX. XXX. XXX. XXX
Cross Load SW On Need Password
50
Off Default
Total Run Time XXXX (Hours)

ICON STAGE USER MANUAL
14
Last Run Time XXXX (Hours)
Temperature Head Temperature XXX℃/℉
Service Setting
Password Password=50
Clear Err. Info
OFF Default
ON Password=50
Fan Speed
Fan Speed
Head2UFan1 xxxx RPM
Head2UFan2 xxxx RPM
… …
Error Info
Error Record 1 (No Error Record…or displays a list of
errors)
Error Record 2 (No Error Record…or displays a list of
errors)
… …
Error Record 10 (No Error Record…or displays a list of
errors)
Test
Self Test
All Pan XXX
Titl XXX
… ...
Internal Functions Strobe XXX
ColorWheel XXX
… ...
Movement Pan XXX
Titl XXX
Individual Function Pan Pan XXX
Titl Titl XXX
… … ...
Manual Control
Pan,
Tilt,
……
Calibrate
Password
PAN
Need Password
50
TILT
Color Wheel
……
Cleaning Mode
Clean Focus
Clean Prism
Clean Zoom

ICON STAGE USER MANUAL
15
9.1 Address
9.1.1. Address
With this function，you can adjust the desired DMX-address via the Control Board.
1) Access the main menu.
1) Tap the <Up/Down> button until “Address” is displayed.
2) Press <ENTER>，the display will show “Address”.
3) Tap the <Up/Down>button，the display will show“A001~AXXX”.
4) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.2 Config
9.2.1 Mode
With this function，you can define the device as slave.
1) Tap <MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Config” is
displayed. Press <ENTER>，the display will show “Config”.
2) Tap the <Up/Down>button until “Mode” is displayed.
3) Press <ENTER>，the display will show“Mode”.
4) The display show“Extended Mode”，Press <Up/Down>，the display will show “Standard
Mode ” .
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.2.2 Select Signal
With this function，you can define the device as slave.
1) Tap <MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Config” is
displayed. Press <ENTER>，the display will show “Config”.
2) Tap the <Up/Down>button until “Select Signal” is displayed.
3) Press <ENTER>，the display will show “Select Signal”.
4) The display show “DMX Only”，Press <Up/Down>，the display will show “Art-Net On IP2”，
“Art-Net On IP10”，“sACN”.
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.2.3 Set Universe
1) Tap <MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Config” is
displayed. Press <ENTER>，the display will show “Config”.
2) Press <Up/Down>，the display will show“Set Universe”.
3) Press< ENTER>，the display will show“Set Universe”.
4) The display show“0000~32767”.
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.2.4 Pan and Tilt
Tilt Reverse
With this function you can reverse the Tilt-movement.
1) Tap <MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Config” is
displayed. Press <ENTER>，the display will show “Config”. Tap the <Up/Down>button until
the display will show “Pan and Tilt”. Press <ENTER>，the display will show “Pan and Tilt”.
2) Press <Up/Down>，the display will show “Tilt Reverse”.
3) Press< ENTER>，the display will show“Tilt Reverse”.
4) The display show “OFF”，Press <Up/Down>，the display will show “ON”.

ICON STAGE USER MANUAL
16
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
Pan Reverse
With this function you can reverse the Pan-movement.
1) Tap <MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Config” is
displayed. Press <ENTER>，the display will show “Config”. Tap the <Up/Down>button until
the
display will show “Pan and Tilt ”.Press <ENTER>，the display will show “Pan and Tilt”.
2) Press <Up/Down>，the display will show “Pan Reverse”.
3) Press< ENTER>，the display will show “Pan Reverse”.
4) The display show “OFF”，Press <Up/Down>，the display will show “ON”.
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
Feedback
With this function，you can feedback switch of pan movement or tilt movement.
1) Tap <MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Config” is
displayed. Press <ENTER>，the display will show “Config”. Tap the <Up/Down>button until
the
display will show “Pan and Tilt ”.Press <ENTER>，the display will show“Pan and Tilt”.
2) Press <Up/Down>，the display will show “Feedback”.
3) Press< ENTER>，the display will show “Feedback”..
4) The display show “ON”，Press <Up/Down>，the display will show “OFF”.
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.2.5 Dimmer Curve
1) Tap<MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Config” is
displayed. Press <ENTER>，the display will show “Config”.
2) Tap the <Up/Down>button until “Dimmer Curve” is displayed.
3) Press <ENTER>，the display will show“Dimmer Curve”.
4) The display show “Standard”，Press <Up/Down>，the display will show “Standard”，“Stage”，
“TV”，“Architectural”，“Theatre”.
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.2.6 Refresh
1) Tap<MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Config” is
displayed. Press <ENTER>，the display will show “Config”.
2) Tap the <Up/Down>button until “Refresh” is displayed.
3) Press <ENTER>，the display will show “Refresh”.
4) The display show “1200Hz”，Press <Up/Down>，the display will show “900~25000Hz”.
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.2.7 Gamma
1) Tap<MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Config” is
displayed. Press <ENTER>，the display will show “Config”.
2) Tap the <Up/Down>button until “Gamma” is displayed.
3) Press <ENTER>，the display will show “Gamma”.
4) The display show “2.0”，Press <Up/Down>，the display will show “2.0~2.8”.
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.

ICON STAGE USER MANUAL
17
9.2.8 Fan Mode
1) Tap<MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Config” is
displayed. Press <ENTER>，the display will show “Config”.
2) Tap the <Up/Down>button until “Fan Mode” is displayed.
3) Press <ENTER>，the display will show“Fan Mode”.
4) The display show “Auto”，Press <Up/Down>，the display will show “Auto”，“High”，“Silent”.
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.2.9 Gobo Scroll
1) Tap<MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Config”is
displayed. Press <ENTER>，the display will show “Config”.
2) Tap the <Up/Down>button until “Gobo Scroll” is displayed.
3) Press <ENTER>，the display will show “Gobo Scroll”.
4) The display show “OFF”，Press <Up/Down>，the display will show “ON”.
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.2.10 Reset Factory Defaults
1) Tap<MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Config” is
displayed. Press <ENTER>，the display will show “Config”.
2) Press <Up/Down>，the display will show “Reset Factory Defaults”.
3) Press< ENTER>，the display will show “Reset Factory Defaults”.
4) The display show “OFF”，Press <Up/Down>，the display will show “ON”.
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.3 Reset Function
With this function you can reset the device via the Control Board. You can select the different reset
functions by turning the encoder.
1) Tap<MODE/ESC>button，access the main menu.
2) Tap the <Up/Down>button until “Reset Function” is displayed.
3) Press <ENTER>，the display will show“Reset Function”.
4) The display show“Reset All”，Press <Up/Down>，the display will show“Reset Pan&Tilt”，
“Reset Others”.
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.4 Communication
9.4.1 Read Dmx Value
With this function you can display the DMX 512 value of each channel. The display automatically
shows the channel with a value changing.
1) Tap<MODE/ESC>button ，access the main menu ，Tap the <Up/Down>button until
“Communication” is displayed. Press <ENTER>，the display will show “Communication”.
2) Tap the <Up/Down>button until “Read Dmx Value” is displayed.
3) Press <ENTER>，the display will show “Read Dmx Value” .
4) The display will show “ALL，Control，Pan，Tilt，……”.
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.4.2 DMX Info
1) Tap<MODE/ESC>button ，access the main menu ，Tap the <Up/Down>button until
“Communication” is displayed. Press <ENTER>，the display will show “Communication”.

ICON STAGE USER MANUAL
18
2) Tap the <Up/Down>button until“DMX Info”is displayed.
3) Press <ENTER>，the display will show“DMX Info”.
4) The display show“DMX Update Rate =XXXX p/s”.
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.4.3 Comm Loss
1) Tap<MODE/ESC>button ，access the main menu ，Tap the <Up/Down>button until
“Communication” is displayed. Press <ENTER>，the display will show “Communication”.
2) Tap the <Up/Down>button until “Comm Loss” is displayed.
3) Press <ENTER>，the display will show “Comm Loss”.
4) The display show “Fade out 30 seconds”，Press <Up/Down>，the display will show “No Fade
on Loss”，“Fade out 30 seconds”，“Fade out 60 seconds”.
5) Press ENTER to confirm or press <MODE/ESC> to return to the main menu.
9.5 Info
9.5.1 Software Version
With this function，you can display the software version of the device.
1) Tap <MODE/ESC>button，access the main menu，Tap the <Up/Down>button until“Info”is
displayed. Press <ENTER>，the display will show “Info”.
2) Press <Up/Down>，the display will show “Software version”.
3) Press< ENTER>，the display will show “Software version”.
4) The display show“X.X.X……”.
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.5.2 ARTNET IP
1) Tap <MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Info” is
displayed. Press <ENTER>，the display will show“Info”.
2) Press <Up/Down>，the display will show “ARTNET IP”.
3) Press< ENTER>，the display will show “ARTNET IP”.
4) The display will show“XXX. XXX. XXX. XXX”.
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.5.3 Cross load Software
1) Tap <MODE/ESC>button，access the main menu，Tap the <Up/Down>button until“Info”is
displayed. Press <ENTER>，the display will show “Info”.
2) Press <Up/Down>，the display will show “Cross load Software”.
3) Press< ENTER>，the display will show “Cross load Software”.
4) The display show “OFF”，Press <Up/Down>，the display will show “ON”. If you want to need
the “ON”，the need password is 50 .
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.5.4 Total Run Time
With this function，you can display the running time of the device. The display shows “XXXX”，
“XXXX”stands for the number of hours.
1) Tap <MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Info” is
displayed. Press <ENTER>，the display will show “Info”.
2) Press <Up/Down>，the display will show “Total run Time”.

ICON STAGE USER MANUAL
19
3) Press< ENTER>，the display will show “Total run Time”.
4) The display will show “XXXX” (Hours).
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.5.5 Last Run Time
With this function，you can display last the running time of the device. The display shows “XXXX”，
“XXXX” stands for the number of hours.
1) Tap <MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Info”is
displayed. Press <ENTER>，the display will show “Info”.
2) Press <Up/Down>，the display will show “Last Run Time”.
3) Press< ENTER>，the display will show “Last Run Time”.
4) The display will show “XXXX” (Hours).
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.5.6 Temperature
Head Temperature
1) Tap <MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Info” is
displayed. Press <ENTER>，the display will show“Info”.Tap the <Up/Down>button
until “Temperature” is displayed. Press <ENTER>，the display will show “Temperature”.
2) Press <Up/Down>，the display will show “Head Temperature”.
3) Press< ENTER>，the display will show “Head Temperature”.
4) The display will show“XXX℃/℃”.
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.5.7 Service Setting
Password——The Password for this function is “50”.
Clr Err Info
With this function you can clean the error information.
1) Tap <MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Info” is
displayed. Press <ENTER>，the display will show “Info”. Tap the <Up/Down>button until
“Service Setting” is displayed. Press <ENTER>，the display will show “Service Setting”.
2) Press <Up/Down>，the display will show “Clr Err Info”.
3) Press< ENTER>，the display will show“Clr Err Info”.
4) The display show “OFF”，Press <Up/Down>，the display will show “ON”.
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.5.8 Fan Speed
With this function，you can set the speed of the running fans. The selection have Head2UFan1，
Head2UFan2，…….
1) Tap <MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Info” is
displayed. Press <ENTER>，the display will show “Info”.
2) Press <Up/Down>，the display will show “Fan Mode”.
3) Press< ENTER>，the display will show “Fan Mode”.
4) The display will show “Head2UFan1= xxxx RPM”，“Head2UFan2= xxxx RPM”，“……”.
5) Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.5.9 Error Info
With this function，you can display the error informatin. The selection have Error Record 1，Error