ICP DAS USA tET Series User manual

The package includes the following items:
What’s in the shipping
package?
tET-P2R2 or
tPET-P2R2
For tET-P2R2/tPET-P2R2
Software CD
Quick Start Guide
(
This Document
)
English/ December 2010/ Version 1.0
Preparations for devices
1. Power Supply:+12 ~ +48 VDC
2. Ethernet Hub.(PoE Ethernet Switch for tPET module only)
3. Make sure your PC has workable network settings.
4. Disable or well configure your Windows firewall and Anti-Virus
firewall first, else the “Search Servers” on page 5 may not
work. (Please contact with your system Administrator)
1
tET-P2R2/tPET-P2R2 Quick Start Guide

Connecting the Power and Host PC
1. Check Init/Normal switch is on
“RUN” position.
2. Connect both the tET/tPET-P2R2 and your computer to the
same sub network or the same Ethernet Switch, and power
tET/tPET-P2R2 on.
2
tET-P2R2/tPET-P2R2 Quick Start Guide

Pin Assignments and Wiring Note
Pin Assignments
Terminal
No. Pin Assignment
14 N/A
13 N/A
12 N/A
11 RL1 COM
10 RL1 NO
09 RL0 COM
08 RL0 NO
07 DI1
06 DI0
05 DI.COM
Terminal
No. Pin Assignment
E1
01 F.G.
02
N/A
03 (R) +Vs
04 (B) GND
Digital Input/Output Wiring
3
tET-P2R2/tPET-P2R2 Quick Start Guide

Wire the DI and DO for self test. The wiring as follows:
1. Connect the RL0 COM and DI0. ( Pin09 connect to Pin06)
2. Supply the External Power +10V to RL0 NO. (External +10V connect to Pin08 )
3. Supply the External Power GND to DI.COM. (External GND connect to Pin05)
DI/DO Modbus Address
(1xxxx) DI address:
Begin address Points Description Bits per
Point Range Access Type
0
(0x0) 1~2 Digital Input 1
0:Off
1:On R
32
(0x20) 1~2 Digital latched status (high) 1 0:no 1:latched R
64
(0x40) 1~2 Digital latched status (low) 1 0:no 1:latched R
(0xxxx) DO address:
Begin address Points Description Bits per
Point Range Access
Type
0
(0x0) 1~2 Digital Output 1 0: Off 1:On R/W
32
(0x20) 1 Clear all DI latched status (high) 1 1: Clear W
33
(0x21) 1 Clear all DI latched status (low) 1 1: Clear W
.
. . . . . . . . . . .
235
(0xEB) 1~2 Power-on value for DO 1 0=Off 1=On R/W/F
267
(0x10B) 1~2 safe value for DO 1 0=Off 1=On R/W/F
For detail “DI/DO Modbus Address” information, please refer to section 5.3 Modbus
Register Map of user’s manual. CD:\NAPDOS\tPET\Document\
http://ftp.icpdas.com/pub/cd/tinymodules/napdos/tPET/document/
4
tET-P2R2/tPET-P2R2 Quick Start Guide

Configuring Ethernet Settings
1. Run the eSearch Utility.
The eSearch Utility is located at:
CD:\Napdos\Software\eSearch\
http://ftp.icpdas.com/pub/cd/tinymodules/napdos/software/esearch/
2. Click “Search Servers” button to search your tET/tPET-P2R2.
3. Double-Click your tET/tPET-P2R2 to configure the settings.
4. Contact your Network Administrator to get correct network
configuration. Modify the network settings and then click “OK”
button. The tET/tPET-P2R2 will restart it-self immediately.
2. Double-Click your tET/tPET
1. Click
“
Search Servers
”
5
tET-P2R2/tPET-P2R2 Quick Start Guide

Testing your tET/tPET
Module
1. Wait 2 seconds and then click the “Search Servers” button
again to ensure the tET/tPET-P2R2 is working well with new
configuration.
2. Click the “Web” button to link the tET/tPET-P2R2 web server.
1. Click
y
our tET/tPET on the list
Click
2. Click
3. Enter the password and click the “Submit” button to enter
the configuration web page. (The factory default password:
Admin)
6
tET-P2R2/tPET-P2R2 Quick Start Guide

4. Control the I/O for simple test.
In the I/O Setting page, check the “bit0”checkbox for setting
ON to DO0 and click “Update Settings” button.
1
2
3
In the Home page, check that the DO0 and DI0 status should show
current status are “ON”.
1
2
3
7
tET-P2R2/tPET-P2R2 Quick Start Guide

Related Information
tET-P2R2/tPET-P2R2 Series Product Page:
http://www.icpdas.com/products/ Remote_IO/PETL7000/tPET-P2POR2.htm
tET/tPET Series Documentations:
CD:\Napdos\tPET\document\
http://ftp.icpdas.com/pub/cd/tinymodules/napdos/tPET/document/
tET/tPET Series Firmware:
CD:\ Napdos\tPET\firmware\
http://ftp.icpdas.com/pub/cd/tinymodules/napdos/tPET/firmware/
NS-205, NS-205PES Product Page (optional):
http://www.icpdas.com/products/Switch/industrial/ns-205.htm
http://www.icpdas.com/products/Switch/industrial/ns-205pse.htm
ICP DAS Web Site: http://www.icpdas.com
Contact Us (E-Mail): [e-mail] , [email protected]
Copyright @ 2010 by ICP DAS Co., Ltd. All Rights Reserved.
8