ICP DAS USA PCI-P16C16U User manual

PCI-P16C16U Quick Start Guide ICP DAS CO., LTD.
1
Website: http:// www.icpdas.com.tw E-Mail: [e-mail] , service.icp[email protected]m
The shipping package includes the following items:
Note: For more details regarding the Card ID and Jumper settings, refer to the PCI-P16C16
Series User Manual.
For PCI-P16C16U
Check the Supplied Items
English/Oct. 2015/Version 1.0
Software Utility CD
(V6.2 or later)
Quick Start Guide
(This Document)
PCI-P16C16U
CA-4002 D-Sub
Connector x 2
CA-4037W
Cable x 1
Board Layout





1. CN1 Connector
(See Section 5 Pin Assignments)
2. CN2 Connector
(See Section 5 Pin Assignments)
3. SW1: Card ID Switch
(The default setting is 0x0.)
4. JP1 ~ JP8, JP9 ~ JP16: Input
Signal Type Jumper
5. J1, J2: Set the Ground Isolation
Protection

PCI-P16C16U Quick Start Guide ICP DAS CO., LTD.
2
Website: http:// www.icpdas.com.tw E-Mail: [email protected]m , [e-mail]
The UniDAQ driver supports Windows 2000 and 32/64-bit versions of Windows
XP/2003/2008/7/8. The driver installation package for PCI-FC16U board can be found on
the companion CD-ROM, or can be obtained from the ICP DAS FTP web site. The driver
is located at:
CD: \NAPDOS\PCI\UniDAQ\DLL\Driver
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/dll/driver/
To install the UniDAQ driver, follow the procedure described below.
Step 1: Double-click the UniDAQ_Win_Setupxxx.exe icon to begin the installation
process.
Step 2: When the “Welcome to the ICP DAS UniDAQ Driver Setup Wizard”screen
is displayed, click the “Next>” button to start the installation.
Step 3: On the “Information”screen, verify that the DAQ card is included in the list of
supported devices, then click the “Next>” button.
Step 4: On the “Select Destination Location”screen, click the “Next>” button to install
the software in the default folder, C:\ICPDAS\UniDAQ.
Step 5: On the “Select Components”screen, verify that the DAQ Card is in the list of
device, and then click the “Next>” button to continue.
Step 6: On the “Select Additional Tasks” screen, click the “Next>” button.
Step 7: On the “Download Information” screen, click the “Next>” button
Step 8: Once the installation has completed, click “No, I will restart my computer later”,
and then click the “Finish” button.
Note: For detailed information about the driver installation, refer to Chapter 2 “Install
UniDAQ Driver DLL” of the UniDAQ SDK User Manual.
Installing the Windows Driver

PCI-P16C16U Quick Start Guide ICP DAS CO., LTD.
3
Website: http:// www.icpdas.com.tw E-Mail: [email protected]m , [e-mail]
Step 1: Shut down and power off the computer.
Step 2: Remove all the covers from the computer.
Step 3: Select an unused PCI slot.
Step 4: Carefully insert the PCI-P16C16U board into the
PCI slot and secure the board in place.
Step 5: Replace the covers on the computer.
Step 6: Reconnect the power supply and power on the
computer.
Step 7: Once the computer reboots, follow any messages that may be displayed to
complete the Plug and Play installation procedure.
Step 8: Open the “Device Manager” in the Control Panel and verify that the
PCI-P16C16U board is listed correctly, as illustrated below.
Installing the Hardware
Installation successful

PCI-P16C16U Quick Start Guide ICP DAS CO., LTD.
4
Website: http:// www.icpdas.com.tw E-Mail: [email protected]m , [e-mail]
Pin Assignments
Extension Cable (CA-4037W):
Conversion from DB-40-pin to DB-37-pin
Notes:
Ext. Power:
External Power Input
GND:
External Power Ground
OUT:
Open Collector Output
DIA:
Digital Input (Point A)
DIB:
Digital Input (Point B)

PCI-P16C16U Quick Start Guide ICP DAS CO., LTD.
5
Website: http:// www.icpdas.com.tw E-Mail: [email protected]m , [e-mail]
Wiring for the Digital Input/Output Test:
Step 1: Connect the DN-37 to the CN1 connector on the board using the CA-3710 cable.
Step 2: Connect the CN1.OUT0 pin (Pin 1) to the CN1.DIA0 pin (Pin12).
Step 3: Connect the External Power Supply GND to the CN1.GND1 pin (Pin22) and
CN1.GND2 pin (Pin26).
Step 4: Connect the External Power Supply +24V to the CN1.Ext.Power1 pin (Pin20)
and CN1.DIB0 pin (Pin30).
Self-Test

PCI-P16C16U Quick Start Guide ICP DAS CO., LTD.
6
Website: http:// www.icpdas.com.tw E-Mail: [email protected]m , [e-mail]
Execute the UniDAQ Utility Program:
Step 1: In Windows 7, click the “Start” button,
point to “All Programs”,and then click the
“ICPDAS”folder. Point to “UniDAQ
Development Kits”and then click the “UniDAQ
Utility”to execute the UniDAQ Utility Program.
Step 2: Confirm that the PCI-P16C16U board has
been successfully installed in the Host system.
Note that the device numbers start from 0.
Step 3: Click the “TEST”button to start the test.
Step 4: Check the results of the Digital Input/Output functions test.
1. Click the “Digital Output”tab.
2. Select “Port0”from the “Port Number”drop-down menu.
3. Check the checkboxes for channels 0.




PCI-P16C16U Quick Start Guide ICP DAS CO., LTD.
7
Website: http:// www.icpdas.com.tw E-Mail: [email protected]m , [e-mail]
4. Click the “Digital Input”tab.
5. Select “Port0”from the “Port Number”drop-down menu.
6. The DI indicators will turn red when the corresponding DO channel 0 is ON.
PCI-P16C16U Series Board Product Page:
http://www.icpdas.com/root/product/solutions/pc_based_io_board/pci/pci-p16c16.html
DN-37, DB-665 and CA-3710 Product Pages (optional):
http://www.icpdas.com/root/product/solutions/pc_based_io_board/daughter_boards/dn
-37.html
http://www.icpdas.com/root/product/solutions/accessories/power_supply/dp-665.html
http://www.icpdas.com/products/Accessories/cable/cable_selection.htm
UniDAQ Documentation and Software:
CD:\NAPDOS\PCI\UniDAQ\
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/
Related Information


