ICP DAS USA PISO-813 User manual

PISO-813/PISO-813U Quick Start Guide ICP DAS CO., LED
1
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
The package includes the following items:
One PISO-813/PISO-813U PCI Board.
One Software Utility CD (V5.2 or later)
One Quick Start Guide (This Document)
One CA-4002 D-Sub connector
For PISO-813/PISO-813U
What’s in the shipping package?
English/ Feb. 2014/ Version 1.2

PISO-813/PISO-813U Quick Start Guide ICP DAS CO., LED
2
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
Step 1: Setup the Windows driver. The driver is located at:
The UniDAQ driver supports 32-/64-bit Windows 2K/XP/2003/Vista/7/8; it
is recommended to install this driver for new user:
CD: \NAPDOS\PCI\UniDAQ\DLL\Driver
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/dll/driver/
The PISO-813 Series classic driver supports Windows 98/NT/2K and 32-bit
XP/ 2003/ Vista/7/8. Recommended to install this driver for have been
used PISO-813 series boards of regular user, please refer to :
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/piso-813/manual/quickstar
t/classic/
Step 2: Click the “Next>”button to start the installation.
Step 3: Check your DAQ Card is or not on supported list, then click the
“Next>”button.
Step 4: Select the installed folder, the default path is C:\ICPDAS\UniDAQ ,
confirm and click the “Next>”button.
Step 5: Check your DAQ Card on list, then click the “Next>”button.
Step 6: Click the “Next>”button on the Select Additional Tasks window.
Step 7: Click the “Next>”button on the Download Information window.
Step 8: Select “No, I will restart my computer later”and then click the
“Finish”button.
For detailed information about the driver installation, please refer to Chapter
2.1 “Getting the UniDAQ Driver DLL Installer package”of the UniDAQ SDK
user manual.
Installing Windows Driver

PISO-813/PISO-813U Quick Start Guide ICP DAS CO., LED
3
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
Please make sure JP1 and JP2 jumper is kept in default setting before
self-test, as follows:
Jumper
JP1: Analog Input Range Selection
Input Range= 20 V (Default)
Input Range = 10 V
Jumper
JP2: Bipolar/Unipolar Selection
Bipolar Mode (Default)
Unipolar Mode
Jumper Setting
1. CON1: 32 channels analog input.
2. JP1: Input range setting.
JP2: Unipolar/Bipolar setting.
3. SW1: Card ID function for
PISO-813U only.
1
2
3

PISO-813/PISO-813U Quick Start Guide ICP DAS CO., LED
4
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
Setting Reference: (*) Default Setting
Analog Input Range
JP2 (Polarity Select)
JP1 (Range Select)
-10 V ~ +10 V (*)
Bipolar
20 V
-5 V ~ +5 V
Bipolar
20 V, 10 V
-2.5V ~ +2.5 V
Bipolar
20 V, 10 V
-1.25 V ~ +1.25 V
Bipolar
20 V, 10 V
-0.625 V ~ +0.625 V
Bipolar
20 V, 10 V
0 ~ 10 V
Unipolar
10 V
0 ~ 5 V
Unipolar
10 V
0 ~ 2.5 V
Unipolar
10 V
0 ~ 1.25 V
Unipolar
10 V
0 ~ 0.625 V
Unipolar
10 V
For more detailed jumper and SW1 information, please refer to manual Sec.
2.2 A/D Converter Operation and Sec. 2.3 Card ID Switch.
(CD:\NAPDOS\PCI\PISO-813\manual\)
Step 1: Shut down and power off your computer.
Step 2: Remove the cover from the computer.
Step 3: Select an unused PCI slot.
Step 4: Carefully insert your I/O card into the PCI slot.
Step 5: Replace the PC cover.
Step 6: Power on the computer.
After powering-on the computer, please finish the Plug&Play steps according
to the prompted messages.
Installing Hardware on PC

PISO-813/PISO-813U Quick Start Guide ICP DAS CO., LED
5
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
CON1 Pin Assignments (Female DB37).
Pin Assignments

PISO-813/PISO-813U Quick Start Guide ICP DAS CO., LED
6
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
Prepare for device:
DN-37 (optional) wiring terminal board.
Provide a stable signal source. (For example, dry battery)
Self-test wiring as follows:
1. Use the DN-37 to connect the CON1 on board.
2. Wire the signal source to channel0, and then keep set the JP1 and JP2
jumper to default (page 3), and wire the signals as follows:
Self-Test

PISO-813/PISO-813U Quick Start Guide ICP DAS CO., LED
7
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
3. Execute the UniDAQ Utility Program.
This program (UniDAQ Utility) will be
placed in the default path after
completing installation.
The UniDAQ Utility.exe is located in:
C:\ICPDAS\UniDAQ\Driver\
(Default path).
4. Get A/D function test result.
Double-Click
1
Confirm the hardware setting.
5
Click “Analog Input” item.
4
Confirm the PISO-813 series
card had successfully installed
to PC. It starts from 0.
2
Click this button
to start test.
3
Click this button
to start test.
6

PISO-813/PISO-813U Quick Start Guide ICP DAS CO., LED
8
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
PISO-813/PISO-813U Card Product Page:
http://www.icpdas.com/root/product/solutions/pc_based_io_board/pci/piso-813.html
DN-37, CA-3710 and DP-665 page (optional):
http://www.icpdas.com/products/DAQ/screw_terminal/dn_37.htm
http://www.icpdas.com/products/Accessories/cable/cable_selection.htm
Documentation and Software:
CD:\NAPDOS\PCI\UniDAQ\
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/
Check analog input on Channel 0 textbox.
The other channels value for floating
number.
9
Related Information
PASS