ICP DAS USA PISO-P32C32U-5V User manual

Technical support: servic[email protected] P1
PISO-P32C32U(-5V)/
PEX-P32C32
Quick Start
v1.4, Dec. 2018
What’s in the box?
Related Information
The package includes the following items:
PISO/PEX-P32C32 Card x 1
Quick Start x 1 (This Document)
CA-4037B Cable x 1
CA-4002 D-Sub Connector x 2
For more detailed information related to the user manual and
software for UniDAQ Driver & SDK:
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/
For more detailed information related to the hardware settings for
PISO/PEX-P32C32 Series Card:
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/piso-dio/manual/

DN-37 and CA-3710 Cable Page (optional):
or
PISO-P32C32U(-5V)
PEX-P32C32

Technical support: servic[email protected] P2
CON1
1 2 3 4
CON2
LED1 LED2
LED3 LED4
DC/DC1 DC/DC2
JP1JP2
SW1
1 Appearance
2 Jumper Settings
Jumpers JP1 and JP2
Jumpers JP1 and JP2 are used to specify whether the Digital Input is
either Internal or External Power. NOTE: Ensure that Jumpers JP1
and JP2 are in the default positions before performing a self-test.
External Power (Default)
Internal Power





DI channel 16-31
DO channel 16-31
Card ID Switch
Jumper JP2
Jumper JP1
DI channel 0-15
DO channel 0-15
LED3: DO indicator
LED4: DI indicator
LED1: DO indicator
LED2: DI indicator



Technical support: servic[email protected] P3
3 Installing a PISO/PEX-P32C32
1) Power off the PC.
2) Remove all covers from the Computer.
3) Carefully insert the PISO/PEX-P32C32
Series Card into PCI/PCIe slot.
4) Replace the PC Covers.
5) Power on the PC.
6) Download or locate the Windows driver.
The UniDAQ driver supports 32-/64-bit Windows XP/2003/2008/7/8/10 .
It is recommended that new users install this driver, which can be
found in the
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/dll/driver/
The PISO-DIO Series classic driver supports Windows 98/NT/2K
and 32-bit XP/2003/2008/7/8/10. Recommended to install this driver
for have been used PISO-P32C32 Series card of regular user, refer to:
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/piso-dio/manual/qui
ckstart/classic/
7) Setup the UniDAQ Driver DLL, click the “Next>”button for all dialogs.
NOTE: For more detailed information related to driver installation,
refer to Chapter 2 “Starting” in the UniDAQ SDK user manual.
8) The operating system will automatically detect the new hardware and
install the necessary drivers after reboot the PC.
9) Open the “Device Manager” to verify that the PISO/PEX-P32C32
Series Card has been correctly installed and is in the Device Manager,
as illustrated
on right.

Technical support: servic[email protected] P4
4 Pin Assignments
NOTES:
1. Ext.GND: External Power Ground
2. Ext.PWR: External Power Input
3. N.C.: None Connect
4. For detailed information abuout the DI and DO wiring note, refer to
Section 2.3 “Isolated DI Architecture”and Section 2.4 “Isolated DO
Architecture”in the PISO-P32C32 Series user manual.
Extension Cable (CA-4037B):
DB-40-Pin conversion DB-37-Pin

Technical support: servic[email protected] P5
5 Wiring the DI and DO for Self-test
1) Verify that Jumpers JP1 and JP2 on the PISO/PEX-P32C32 Series
Card are set to the “External Power (default)”position. Refer to
Chapter 2 “Jumper Settings”above (P2).
2) Connect the DN-37 to CON1 on the PISO/PEX-P32C32 Series Card
using the CA-3710 cable.
3) Connect the DI <0-15> (Pin2 - Pin17) with DO <0-15>(Pin21 –Pin36).
i.e., DI0(Pin2) with DO0(Pin21) …DI15(Pin17) with DO15(Pin36).
The External Power Wiring for PEX-P32C32/PISO-P32C32U:
4) Connect the External Power Supply +9V ~ +24 V to COM1A (Pin18)
and Ext.PWR0 (Pin37), see Figure 1-1.
5) Connect the External Power Supply GND to COM1B (Pin19) and
Ext.GND0 (Pin1/Pin20), see Figure 1-1.
NOTE: The PEX-P32C32/PISO-P32C32U suggests input voltage range +9 to
+24 V (Logic high). (Higher voltage over the limitation will cause the hardware
damage.)
The External Power Wiring for PISO-P32C32U-5V:
4) Connect the External Power Supply +5V ~ +12 V to COM1A (Pin18)
and Ext.PWR0 (Pin37), see Figure 1-2.
5) Connect the External Power Supply GND to COM1B (Pin19) and
Ext.GND0 (Pin1/Pin20), see Figure 1-2.
NOTE: The PISO-P32C32U-5V suggests input voltage range +5 to +12V (Logic
high). (Higher voltage over the limitation will cause the hardware damage.)

Technical support: servic[email protected] P6
Figure 1-1: The PEX-P32C32/PISO-P32C32U wiring:
-----------------------------------------------------------------------------------------------
Figure 1-2: The PISO-P32C32U-5V wiring:
DN-37 I/O Wiring
13 4 5 6 7 8 9 10 11 13 14 17 15 16 18
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
12
2
37
19
+24V
GND
External
Power Supply
(+9V ~ +24V)
CA-3710
CON1
DN-37 I/O Wiring
13 4 5 6 7 8 9 10 11 13 14 17 15 16 18
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
12
2
37
19
+5V
GND
External
Power Supply
(+5V ~ +12V)
CA-3710
CON1

Technical support: servic[email protected] P7
6 Testing your PISO/PEX-P32C32
1) Launch the UniDAQ Utility software. The UniDAQ Utility will be
placed in the default path “C:\ICPDAS\UniDAQ\Driver”after
completing installation.
2) Confirm that PISO-P32C32 Series Card has been successfully
installed in the Host system. Note that the device numbers start
from 0.
3) Click the “TEST”button to start the test.
Double-Click



Technical support: servic[email protected] P8
4) Click the “Digital Output”tab.
5) Select “Port0”from the “Port Number”drop-down menu.
6) Click the DO channels 0, 2, 4 and 6 buttons.
7) Click the “Digital Input”tab.
8) Select “Port0”from the “Port Number”drop-down menu.
9) The DI indicators will turn black when the corresponding DO
channels 0, 2, 4 and 6 are high.
NOTE: Port0/1 DI is the reverse logic, so the red light means low
status (Logic 0) and the black light means high status (Logic 1).






Port0: DO0-7
Port1: DO8-15
Port2: N.C.
Port3: N.C.
Port0: DI0-7
Port1: DI8-15
Port2: N.C.
Port3: N.C.