ICP DAS USA ET-87Pn-MTCP User manual

Copyright © 2014 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [e-mail]
ET-87Pn-MTCP Quick Start Guide
1
Quick Start Guide for
ET-87Pn-MTCP
May 2014, Version 1.0.2
Congratulations on purchasing ET-87Pn-MTCP - a Modbus TCP I/O expansion unit to
expand I-87K series I/O modules and the most popular automation solution for remote
monitoring and control application. This Quick Start Guide will provide information
needed to get started. Please also consult the User Manual for detailed information on
the setup and use of ET-87Pn-MTCP.
In addition to this guide, the package includes the following items:
ET-87Pn-MTCP Software Utility CD Screw Driver
(ET-87P4-MTCP/ET-87P8-MTCP) (1C016)
●ET-87Pn-MTCP Reference Document
CD:\Napdos\Modbus\ET87Pn\Document\
http://ftp.icpdas.com/pub/cd/8000cd/napdos/modbus/et87pn/document/
●ET-87Pn-MTCP Website
http://www.icpdas.com/root/product/solutions/pac/ipac/et-87pn-mtcp.html
●ICP DAS Website
http://www.icpdas.com/
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

Copyright © 2014 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [e-mail]
ET-87Pn-MTCP Quick Start Guide
2
1
Mounting the Hardware
The ET-87Pn-MTCP installation must provide proper ventilation, spacing, and grounding
to ensure the equipment will operate as specified. A minimum clearance of 50mm
between the ET-87Pn-MTCP and the top and bottom side of the enclosure panels must
be provided.
2
Connecting to PC, Network and Setting up the Power
i. Connect PC to LAN1 port through a hub. The ET-87Pn-MTCP is equipped with RJ-45
Ethernet ports for connection to an Ethernet hub/switch and PC. You can also link directly
the ET-87Pn to PC with an Ethernet cable.
ii. Connect the +24 VDC power supply to PWR1 and GND terminals.
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

Copyright © 2014 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [e-mail]
ET-87Pn-MTCP Quick Start Guide
3
3
Installing the Modbus Utility
The Modbus Utility can be obtained from companion CD or ICP DAS FTP
site:
CD:\Napdos\Modbus\Modbus_Utility\
ftp://ftp.icpdas.com/pub/cd/8000cd/napdos/modbus/modbus_utility/
4
Using the Modbus Utility to Assign a New IP Address
UDP Search of the Modbus Utility can be used to configure the IP address. Before
starting the configuration process, ensure that the LAN1 are used to connect to network
and make the controller under the running firmware mode. The default IP addresses
are as follows:
Item LAN1 (default)
IP Address 192.168.255.1
Subnet Mask 255.255.0.0
Gateway 192.168.0.1
Step 1: Run the Modbus Utility, and then search the ET-87Pn-MTCP.
i. Double-click the Modbus Utility shortcut on the desktop.
ii. Select UDP Search from the Client Toolsmenu.
iii. Click the Search Servers button of the eSearch Utility dialog, waiting for
the search to be done.
ii. Select UDP Search
iii. Click the
Search Servers
button,
waiting for the search to be done.
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

Copyright © 2014 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [e-mail]
ET-87Pn-MTCP Quick Start Guide
4
Step 2: Configure IP Address.
i. Select the
“Name” field
from the default
IP address row
of
ET-87Pn-MTCP.
ii. Click the
Configuration
(UDP) button to
open the setting
dialog.
iii. Configure the IP
settings.
iv. Click the OK
button to save
the
configuration.
5
Inserting and Wiring the I/O Modules
There are various types of I/O expansion modules for interfacing many
different field devices to the ET-87Pn-MTCP.
For more information about I/O
expansion module, please refer to
http://www.icpdas.com/products/PAC/xpac/remote_io_support_list.htm
i. Click the “Name” column of ET-87Pn-MTCP.
ii. Click the Configuration (UDP) button.
iv. Click the OK button.
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

Copyright © 2014 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [e-mail]
ET-87Pn-MTCP Quick Start Guide
5
6
Using the Modbus Utility to Configure the Module
The Modbus Utility can be used to make the communication between the
ET-87Pn-MTCP and PC/Laptop via the Modbus/TCP protocol.
Step 1: Run the Modbus Utility and connect to ET-87Pn-MTCP.
i. Double-click the Modbus Utility shortcut on the desktop.
ii. Click the Modbus/TCP button in the middle of the Select
Controller dialog.
iii. Enter the IP address, and then click the Connect button.
Enter the IP address, and then
click the Connect button.
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

Copyright © 2014 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [e-mail]
ET-87Pn-MTCP Quick Start Guide
6
Step 2: Match the I/O module and then get the I/O configuration information.
i. Click the Refresh button to match the I/O modules to configuration of the controller.
ii. Select the About option from the Help menu to get the I/O configuration and firmware
information.
iii. Check the module status diagram, ensuring for the I/O modules to be matched.
i. Click the Refresh button.
iii. See the module status diagram,
ensuring for the I/O modules to
be matched.
ii. Select the About option
from the
Help
menu.
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

Copyright © 2014 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [e-mail]
ET-87Pn-MTCP Quick Start Guide
7
Step 3: Set I/O configuration, get the I/O values and then save the I/O
configuration.
i. Configure the I/O settings, such as Range Code, Power-on and Safe values.
ii. Select the Timer Interval from the Monitor menu to set the monitoring interval.
ii. Select the Timer Interval to
set the monitoring interval.
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

Copyright © 2014 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [e-mail]
ET-87Pn-MTCP Quick Start Guide
8
iii. Click the Monitor icon to start retrieving I/O values. The I/O values will be
displayed in the Mapping tables.
iv. Select File option from the Save menu and select a location where the configuration
file is about to be saved. This operation can save the controller configuration and I/O
settings to an “ini” file, and the file can be loaded by Load function at the next time
when using the same controller and I/O modules.
iv. Click File to save the
configuration file.
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru