ICP Electronics LCD-Kit01 User manual

LCD-Kit01
640x480 – 18bits
P64CV1 LCD Display
©Copyright 1999 by ICP Electronics Inc. All Rights Reserved.
Manual first edition May01, 1999.
The information in this document is subject to change without prior
notice in order to improve reliability, design and function and does
not represent a commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect,
special, incidental, or consequential damages arising out of the use
or inability to use the product or documentation, even if advised of
the possibility of such damages.
This document contains proprietary information protected by
copyright. All rights are reserved. No part of this manual may be
reproduced by any mechanical, electronic, or other means in any
form without prior written permission of the manufacturer.

LCD-Kit01 640 x 480 / 18 bits
P64CV1
1
Contents
1. Introduction ........................................................................ 2
1.1 Specifications.................................................................................. 3
1.2 What You Have............................................................................... 4
2. Installation.......................................................................... 5
2.1 LCD-01 Connection Board Layout .................................................. 5
2.2 LCD-Kit01 Connection Layout......................................................... 6
2.3 Unpacking Precautions………………………………………………... 7
2.4 Horizontal and Vertical Image Shift................................................. 8
2.5 Backlight Inverter Control................................................................ 9
3. LCD-Kit01 Connectors.....................................................10
3.1 LCD Connector ............................................................................. 10
3.2 Backlight Connector...................................................................... 14
3.3 Keyboard Connector ..................................................................... 14
4. Voltage and BIOS Setting................................................15
4.1 BIOS Setting for SBCs with C&T 65555 Chipset .......................... 16
4.2 BIOS Setting for SBCs with HM86508 Chipset ............................. 17
Appendix A. P64CV1 Display - Switch Setting.. .................. 18
LCD-Kit01 640 x 480 / 18 bits
P64CV1
2
1
Introduction
Welcome to the LCD-Kit01 – P64CV1. The LCD-Kit01 is high
brightness Amorphous Silicon TFT LCD panel with 640 x 480
resolution and 18-bits display colors. It is compatible with VGA-
480, VGA-400, VGA-350 and free format – four kinds of VGA
timing. It is made for the system manufacturers, integrators, or
VARs that want to provide all the performance, reliability, and
quality at a reasonable price.
The LCD-Kit01 is designed with Color Filter, Wide View Angle,
High Contrast and Aperture Ratio to present a High Image
Quality. With its thin and light weight plus small and compact
size (6.4”), LCD-Kit01 is also the most suitable solution for
industrial portable workstation.
The LCD-Kit01 comes with specifically designed mounting kit for
fast installation. It is also Plug and Play, can be directly and
easily connected to JUKI, NOVA, POS,… series main boards
and also PLC-655, PLC-508 LCD control card without any
additional parts needed.

LCD-Kit01 640 x 480 / 18 bits
P64CV1
3
1.1 Specifications :
Supply Voltage : +5V
Panel Size: 6.4” (17cm) Diagonal
Display Active Area Size: 129.60mm (H) x 97.44mm (V)
Total Display Size: 140.12mm (H) x 110.00mm (V)
Display Colors: 18-bits = 262.144 Colors
Number of Pixels: 640 (H) x 480 (V)
Brightness : 300 cd/m2
Pixel Format: 1 pixel = R + G + B dots
Pixel Arrangement: R, G, B Vertical Strip
Pixel Pitch: 203μm (H) x 203μm (V)
Dot Pitch: 67.5μm (H) x 203μm (V)
Image Reversion: Up/Down and Left/Right
Viewing Direction: 6 o’clock
Viewing Angle: +/- 50o(H), -10o ~ +30o(V)
Contrast Ratio: > 100 : 1
Outline Dimensions: 168.9mm (W) x 120.0mm (H) x 13.0mm (D)
Surface Treatment: Hard Coating (or Anti-reflection)
Operating Temperature : 0~55oC
LCD MTBF : 50,000 hours
Backlight MTBF : 10,000 hours (min)
LCD-Kit01 640 x 480 / 18 bits
P64CV1
4
1.2 What You Have
In addition to this User's Manual, the LCD-Kit01 package includes
the following items:
•one P64CV1 6.4” LCD Panel with its mounting kit
•one 70cm 44-pin LCD connection cable
•one BIOS Utility Diskette
If any of these items is missing or damaged, contact the dealer
from whom you purchased the product. Save the shipping
materials and carton in case you want to ship or store the product
in the future.

LCD-Kit01 640 x 480 / 18 bits
P64CV1
5
2
Installation
This chapter describes how to install the LCD-Kit01. The layout
of LCD-01 Connection Board is shown on the next page and the
Unpacking Precautions that you should be careful with are
described on the following page. Also included is the jumpers,
connectors and switches setting for this LCD-Kit01.
2.1 LCD-01 Connection Board Layout
< please, refer to the next page >
LCD-Kit01 640 x 480 / 18 bits
P64CV1
6
2.2 LCD-Kit01 Connection Layout

LCD-Kit01 640 x 480 / 18 bits
P64CV1
7
2.3 Unpacking Precautions
 Some components on LCD-Kit01 are very sensitive to static electric
charges and can be damaged by a sudden rush of power. Ground
yourself to remove any static charge before touching your LCD-
Kit01 . You can do it by using a grounded wrist strap at all times or
by frequently touching any conducting materials that is connected to
the ground.
 Do not touch the inner side of LCD module and the connector/cable
of fluorescent lamp/backlight when the power is on. The inverter
supplies HIGH VOLTAGE to these parts (~ 300Vrms).
 Disconnect power supply before handling and doing connection on
LCD-Kit01. Do not plug any connector or jumper while the power is
on. It will cause fatal damage to your LCD panel.
 Make sure that every connector is connected in correct direction.
Any incorrect connection may cause smoke or burn of electrical
parts or fatal damage of your LCD panel.
 Be careful with the liquid crystal material. Do not swallow, inhale or
have skin contact with this material in case that the LCD panel is
broken and the liquid flow out. If you inhale the liquid material, rinse
your mouth immediately with water then go to see a doctor. If you
have skin contact with the liquid, wash it immediately with alcohol.
Be careful, too, with the chips of glass if the panel is broken.
LCD-Kit01 640 x 480 / 18 bits
P64CV1
8
or J5 pad short
2.4 Horizontal and Vertical Image Shift
•JP1 : Horizontal Image Shift-direction Jumper
This setting also can be done by shorting J3 or J4
Disaster note: Do not short both J3 and J4
•JP2 : Vertical Image Shift-direction Jumper
This setting also can be done by shorting J5 or J6
Disaster note: Do not short both J5 and J6
or J3 pad
short
or J3, J5 pads
short
default
setting

LCD-Kit01 640 x 480 / 18 bits
P64CV1
9
2.5 Backlight Inverter Control
•JP3: Backlight Inverter ON/OFF control
PIN NO. FUNCTION
1-2 USE FPVEE
2-3 USE ENBKL
•J1, J2: Backlight Inverter ON/OFF control,
Use these jumpers only if JP3 is not in use (short pad)
J1 J2 FUNCTION
OFF ON ENBKL
ON OFF FPVEE
LCD-Kit01 640 x 480 / 18 bits
P64CV1
10
3
LCD-Kit01 Connectors
3.1 LCD Connector
CN1 or CN4 can be used as LCD Connector to connect your LCD-
Kit01 to the LCD Control Card of your SBC. Choose only one of
them.
•CN4: 22x2 Header/2.0mm LCD Connector
(connect to LCD Control Card)
PIN NO FUNCTION PIN NO FUNCTION
1 +12V 2 +12V
3 GND 4 GND
5 +5V 6 +5V
7 FPVEE 8 GND
9 P0 10 P1
11 P2 12 P3
13 P4 14 P5
15 P6 16 P7
17 P8 18 P9
19 P10 20 P11
21 P12 22 P13
23 P14 24 P15
25 P16 26 P17
27 P18 28 P19
29 P20 30 P21
31 P22 32 P23
33 GND 34 GND
35 SHFCLK 36 FLM
37 M 38 LP
39 GND 40 ENBKL
41 GND 42 NC
43 +5V 44 NC

LCD-Kit01 640 x 480 / 18 bits
P64CV1
11
•CN1: DSUB-44 Pin LCD Connector
(connect to LCD Control Card; optional)
Pin Function Pin Function Pin Function
1 +12V 16 P7 31 P22
2 +12V 17 P8 32 P23
3 GND 18 P9 33 GND
4 GND 19 P10 34 GND
5 +5V 20 P11 35 SHFCLK
6 +5V 21 P12 36 FLM
7 FPVEE 22 P13 37 M
8 GND 23 P14 38 LP
9 P0 24 P15 39 GND
10 P1 25 P16 40 ENBKL
11 P2 26 P17 41 KB-DAT
12 P3 27 P18 42 KB-CLK
13 P4 28 P19 43 C-VR1
14 P5 29 P20 44 C-VR2
15 P6 30 P21
LCD-Kit01 640 x 480 / 18 bits
P64CV1
12
•CN8: LCD OUTPUT Connector
(connect to Panel Display)
PIN NO. FUNCTION PIN NO. FUNCTION
1 SHFCLK 16 P14
2 LP 17 P15
3 FLM 18 GND
4 GND 19 P2
5 P18 20 P3
6 P19 21 P4
7 P20 22 P5
8 P21 23 P6
9 P22 24 P7
10 P23 25 GND
11 GND 26 M
12 P10 27 +5V
13 P11 28 +5V
14 P12 29 R/L *
15 P13 30 U/D *
Note:1. *the same function as CN7
2. Choose only one of CN8 or CN7 to be used.

LCD-Kit01 640 x 480 / 18 bits
P64CV1
13
•CN7: LCD OUTPUT DF9-31S-1V Connectors
(connect to Panel Display; optional)
PIN NO. FUNCTION PIN NO. FUNCTION
1 GND 2 SHFCLK
3 LP 4 FLM
5 GND 6 P18
7 P19 8 P20
9 P21 10 P22
11 P23 12 GND
13 P10 14 P11
15 P12 16 P13
17 P14 18 P15
19 GND 20 P2
21 P3 22 P4
23 P5 24 P6
25 P7 26 GND
27 M 28 +5V
29 +5V 30 R/L *
31 U/D **
Note: * R/L is the Right/Left shift signal for LCD P64CV1
** U/D is the Up/Down shift signal for LCD P64CV1
LCD-Kit01 640 x 480 / 18 bits
P64CV1
14
3.2 Backlight Connector
•CN3: Backlight Inverter Connector
PIN NO. DESCRIPTION
1 +12V
2 Vadj
3 GND
4 ON/OFF
•CN5: JST-2Pin/2.5mm Backlight Inverter ON/OFF Switch
PIN NO. DESCRIPTION
CLOSE Inverter ON
OPEN Inverter OFF
•CN6: JST-3Pin/2.5mm Backlight VR Connector
(Resistor Potentiometer)
PIN NO. DESCRIPTION
1 Series 1K Ohm To +5V
2 Vadj
3 GND
Note: This Connector is plugged with 3-Wired VR
3.3 Keyboard Connector
•CN2: Keyboard Connector (JST-5Pin/2.5mm; optional)
PIN NO. DESCRIPTION
1 KB-CLK
2 KB-DAT
3 NC
4 GND
5 +5V
Note: This is an optional connector. It can be used only in connection with
PM-1035 DC to DC Module under the situation where the distance
between your SBC and LCD display is 70cm ~ 2m. Visit
www.icpacquire.com.tw for more information on PM-1035.

LCD-Kit01 640 x 480 / 18 bits
P64CV1
15
4
Voltage and BIOS Setting
After all jumpers and connectors have been set and connected
correctly, the next step is to set the Voltage and BIOS of the LCD-
Kit01. These settings are done on your SBC.
Voltage Setting
The Supply Voltage for LCD-Kit01 is +5V. You must set the LCD
Voltage Setting Jumper on your SBC to +5V. Please, refer to SBC
User Manual of your SBC or refer to the following tables.
BIOS Setting
For SBCs with C&T 65555 LCD/CRT Interface Chipset, the setting
can be done simply in CMOS Setup. For SBCs with HM86508
LCD/CRT Interface Chipset, the BIOS setting must be done by
upgrading the VGA BIOS using the BIOS file in the attached disk.
Please, refer to the following tables for more detail information.
Note: To do the above settings, you must have one VGA monitor
connected to your SBC because your LCD-Kit01 may not work
correctly or even does not show anything before the Voltage and
BIOS settings are correct.
LCD-Kit01 640 x 480 / 18 bits
P64CV1
16
4.1 BIOS Setting for SBCs with C&T 65555 Chipset
BIOS Setup LCD Volt. Setting
JUKI-710 Standard CMOS Setup: JP9: 2-3 > ON
LCD&CRT: Auto or Both 5-6 > ON
Panel & P.M.U. Setup:
Panel Type: 6 :640x480 18Bit TFT Color
JUKI-740E Peripheral Setup: JP39: 2-3 > ON
LCD&CRT Selection : Auto or Both
LCD Type : #6 640x480 18bit
JUKI-745E Peripheral Setup: JP39: 2-3 > ON
LCD CRT Selection: Auto or Both
LCD Type : #6 640x480 18bit
NOVA-600 Peripheral Setup: JP10: 2-3 > ON
LCD CRT Selection: Auto or Both
LCD Type : #6 640x480 18bit
POS-566 Peripheral Setup: JP23: 2-3 > ON
LCD CRT Selection: Auto or Both
LCD Type : #6 640x480 18bit
LCD-Kit01

LCD-Kit01 640 x 480 / 18 bits
P64CV1
17
4.2 BIOS Setting for SBCs with HM86508 Chipset
Note : to upgrade the BIOS, under DOS prompt insert the
attached disk then type the bold letter command of the middle
column then follow the instruction on your monitor.
Example: for NOVA-300 SBC, under DOS prompt type:
A:\ flash634 n300lcd1.rom or
C:\ flash634 n300lcd1.rom if you have copied the files
flash634.com and n300lcd1.rom to your hard-disk.
BIOS Setup LCD Volt. Setting
JUKI-730 use flash634 j730lcd1.rom to upgrade bios No volt. Setting
(ALi6117) (5V only)
JUKI-732E use flash634 j732lcd1.rom to upgrade bios No volt. Setting
(ALi6117) (5V only)
JUKI-750E use flash631 j750lcd1.rom to upgrade bios No volt. Setting
(ACC Maple) (5V only)
JUKI-752 use flash631 j752lcd1.rom to upgrade bios No volt. Setting
(ACC Maple) (5V only)
PM-1021 use flash634 1021lcd1.rom to upgrade bios No volt. Setting
(ALi6117) (5V only)
NOVA-300 use flash634 n300lcd1.rom to upgrade bios No volt. Setting
(ALi6117) (5V only)
WAFER-4823 use flash631 4823lcd1.rom to upgrade bios No volt. Setting
(ACC Maple) (5V only)
LCD-Kit01
LCD-Kit01 640 x 480 / 18 bits
P64CV1
18
Appendix A. P64CV1 Display – Switch Setting
There are two switches on the back of LCD01 Display. These
switches have been set to the factory-setting. Your LCD01 comes
in ready-to-use condition, don’t change this setting unnecessary.
Notes: 1. HP6~HP0 is for picture level setting
2. U/D is for picture horizontal rotation
3. R/L is for picture vertical rotation
4. Don’t change the ‘system internal setting’