ICP Global Pty UDP1000P User manual

UDP1000P

HDMI/DVIKVMExtender
SetupGuide
(ForFirmwareA6.3.1up,23Sep.2016)











ForSalesandServicepleasecontact

EastgardensOfficeTower
Suite603,Level5,
152BunnerongRoad
PAGEWOODNSW2035
Tel‐0293142092
Fax‐0293449537
















PanelandConnectors
UDP1000TTransmitter


No.Connector Description
1EthernetConnecttoGigabitEthernetswitchordirectlytoUDP1000R.
2DVIIn ConnecttoHDMIorDVISource.
3Linein Audiolinein,itwillbeextendedtotheLineOutofUDP1000R.
4Lineout Audiolineout,itisextendedfromMic.InofUDP1000R.
5USB‐to‐PC ConnectthisUSBtoPCtoprovideRemoteVirtualUSBforUDP1000R.
6DC12VIn Systempowerinput.
7SystemLED(Green)
LinkLED(Amber)
GreenBlinking/AmberOff:Systemisstartingup.
GreenOn/AmberOff:Systemisready,butTX/RXnotconnected.
GreenOn/AmberBlinking:TX/RXconnected,butwaitingforHDMIinput.
GreenOn/AmberOn:TX/RXconnected,HDMIinputisready.
8RS‐232 ProvideSerial‐over‐IPfunction.(TxD,RxD,GND)
9IRBlaster ConnecttoexternalIRLED
10LinkID
4bithardwareGroupID.ItcanbeoverwrittenbythesoftwareGroup‐IDofSettingprogram
orConnectionManager.
11(Button1)
PressandHoldatPower
ONuntilGreenandAmberLED
blinking
1. ResettotheFactorydefaultsetting.
2. EnterSetupandFirmwareupgrademodein
192.168.0.88
12(Button2)
ShortpressSettoVideo/Graphicmode.
Longpress(3sec.)
ToEnable/DisableAnti‐Dither.
Note:ForsomeofATIgraphiccardwith
Ditheringfunctionenabled,youmayenable
Anti‐Dithertoachievethebettervideoquality.
PressandHoldatPowerON
untilGreenLEDblinking
GetandUseEDIDfromLoop‐outmonitor



UDP1000RReceiver

No.Connector Description
1EthernetConnecttoGigabitEthernetswitchordirectlytoUDP1000T.
2Modebutton
ShortpressSettoVideoorGraphicmode.
Longpress(3sec.)
ToEnable/DisableAnti‐Dither.Note:For
someofATIgraphiccardwithDithering
functionenabled,youmayenableAnti‐
Dithertoachievethebettervideoquality.
PressandHoldatPowerONuntilGreenLED
blinking
GetandUsethisRX’sEDIDasthesystem
EDID
3Linkbutton
Shortpress
Toenable/disableTransmitterListOSD
Longpress(3sec.)TogettheUSBaccessright.
PressandHoldatPowerONuntilGreenand
AmberLEDblinking
1. ResettotheFactorydefault.
2. EnterSetupandFirmwareupgrade
modein192.168.0.88
4VideoOut ThisDVI‐IconnectorsupportsHDMI/DVI‐DandVGAoutput.UseDVI‐to‐DVIorDVI‐to‐HDMI
orDVI‐to‐VGAcableforDVI/HDMI/VGAmonitor.
5Mic.IN MicrophoneInput,itwillbeextendedtotheLineOutofUDP1000T.
6LineOUT Audiolineout,itisextendedfromLineInofUDP1000T.
7DC12VIn Systempowerinput.
8SystemLED(Green)
LinkLED(Amber)
GreenBlinking/AmberOff:Systemisstartingup.
GreenOn/AmberOff:Systemisready,butTX/RXnotconnected.
GreenOn/AmberBlinking:TX/RXconnected,butwaitingforHDMIinput.
GreenOn/AmberOn:TX/RXconnected,HDMIinputisready.
9RS‐232 ProvideSerial‐over‐IPfunction(optional).
10IRReceiver RemoteUniversalIRreceiver(optional).
11LinkID
4bithardwareChannelselectID.ItcanbeoverwrittenbythesoftwareCh‐SelectofSetting
programorConnectionManager.
12USBHost
3USB‐Aports,thedefaultsettingareUSB‐over‐IPmodecansupportUSBDisk,
TouchScreen,Printer,keyboard,mouse…(butnotisochronousdevice)



Configuration
TheTX/RXunitbuiltwithWebpageforSetupmodeandOperationmodeconfigurations.
SetupModeConfiguration
1. PressandHoldtheTX/RX’s[Button1]/[Link]buttonandPowerONuntilGreenandAmberLED
blinkingthenreleasethebutton.ThiswillforceTX/RXenterSetupmode.
2. DirectlyconnectTXorRXtoPCLANport,setPCIPto192.168.0.1,NetMask255.255.255.0.
3. OpenPC’sWebBrowser(recommendChrome)andenter192.168.0.88<Enter>
4. TheSetupModeWebpagecontaining[System]tabwithsub‐tabsof[VersionInformation],
[UpdateFirmware],[Utilities],and[Statistics].
ResettoFactorydefault(SetupMode)
Ifthedevicesettingslost,youcanresetthedevicebacktothefactorydefault:
1. EnterSetupModeWebpage[System]‐‐‐>[Utilities]‐‐‐>[FactoryDefault]
(TheFactorydefaultsettingareshownonthelabelthatundertheTX/RXunit)
FirmwareUpgrade(SetupMode)
1. EnterSetupModeWebpage[System]‐‐‐>[UpdateFirmware]‐‐‐>navigatetothefirmwarefile
(.bin)thenclick[Upload]tostartfirmwareupgrade.
2. Thefirmwareupgradetakesabout3min.,itwilldisplay“DONERebooting…”toindicatetheunit
hasbeenupgradedandrebooted.
OperationModeConfiguration
TheTX/RXcanbeconfiguredinOperationModethroughEthernetSwitchordirect
connection.ToenterOperationmodeWebpage:
1. SetPCIP10.0.1.1,NetMask255.0.0.0.
2. OpenBrowser(recommendChrome)thenenterTX/RXIP:10.xx.xx.xx
3. TheTX/RXOperationModeWebpageareshownasthebelowscreenshots.TheTXcontains3
tabmenus[System],[Network],Functions],theRXcontains4tabmenus[System],[Video
Wall],[Network],Functions]:

FirmwareUpgrade(OperationMode)
ItispossibletodothefirmwareupgradeinOperationmodeforTX/RX:
1. EnterOperationModeWebpage[System]‐‐‐>[UpdateFirmware]‐‐‐>navigatetothefirmware
file(.bin)thenclick[Upload]tostartfirmwareupgrade.
2. Thefirmwareupgradetakesabout3min.,itwilldisplay“DONERebooting…”toindicatetheunit
hasbeenupgradedandrebooted.
NetworkConfiguration
TheTX/RXprovidesthefollowingNetworkrelatedsettings:

TochangeIP
EnterTX/RXOperationModeWebpage
[Network]‐‐‐>[IPSetup]‐‐‐>selectAutoIP,DHCP,
Static‐‐‐>enterdeviceIP,SubnetMask,Default
Gateway‐‐‐>[Apply].
TochangeCastingMode
TheUDP1000T/RfactorydefaultisUnicast.To
change,enterTX/RXOperationModeWebpage
[Network]‐‐‐>[CastingMode]‐‐‐>select[Multicast]
or[Unicast]‐‐‐>[Apply].
ConnectionMethod(RXonly)
Thereare4ConnectionMethodsforMulticast
RX:FirstAvailable,MulticastIP,OSDTransmitter
List,andDirectConnection. 
Thereare3ConnectionMethodsforUnicastRX:
OSDTransmitterList,TXIPandDirectConnection.
FirstAvailable:theRXwillconnecttothefirst
availableTX.
MulticastIP:225.0.xxx.xxx:theRXwillconnectto
theTXthatisusingthesameMulticastIPaddress.(YoucansetupTXMulticastIPonthe
TX[Network]‐‐‐>[CastingMode])
OSDTransmitterList:theRXwillshowuptheavailableTransmittersforusertoselect.TXIP:
x.x.x.x:theRXwillconnecttothisdedicatedTXonly.
DirectConnection:thissettingenablesRXtoconnectTXbythesamesubnet,sameCastingMode,
JumboFramewillbeenabled.
ToshowTXDevicenamewhenconnected(RXonly)
ThisfeatureenableRXtopopuptheTXname(orIP)whenconnected.Defaultisenabledwith5
seconds.
ToEnable/DisableJumboFrame
Toenableordisableit,enterTX/RXOperationmodeWebpage‐‐‐>[Network]‐‐‐>[JumboFrame]‐‐
‐>Enable/Disable‐‐‐>[Apply]‐‐‐>theunitwillsavethesettingandrebootautomatically.

FunctionsConfiguration
TheTX/RXprovidesOperationmodeWebpageforFunctionsConfiguration.Thefollowing
screenshotshowsRXWebpageasanexample(TXissimilar):

TochangeDeviceName
EnterTX/RXOperationmodeWebpage‐‐‐>[Functions]‐‐‐
>[DeviceName]‐‐‐>entername(8characters)‐‐‐>[Apply]
tosavethedevicename.
ToEnable/DisableKMoverIP
ThesystemsupportsbothUSB‐over‐IPandKM‐over‐IPfor
USBextension.TheUSB‐over‐IPworksasavirtual5‐port
USBHUBwhenTXisconnectedtoPC,itiscompatiblewith
mostofUSBdevicessuchaskeyboard,mouse,PenDrive,
TouchScreen…etc.
TheKM‐over‐IPisaHIDemulationbuiltformultipleRXsto
sharekeyboard/mouseforonePC,ittakesoneportofthe
5virtualports.TheKM‐over‐IPsettingisdifferentforTX
andRX:
ForTX:enterTXOperationmodeWebpage‐‐‐>
[Functions]‐‐‐>[USBoverIP]‐‐‐>[CompatibilityMode]‐‐‐
>check/uncheck[K/MoverIP]toEnable/Disable‐‐‐>
[Apply](defaultenabled).
ForRX,enterRXOperationmodeWebpage‐‐‐>
[Functions]‐‐‐>[KMoIPports]‐‐‐>check/uncheck1,2,3toEnable/DisableKM‐over‐IPports
(defaultalldisabled)‐‐‐>[Apply].
TodefineHotkey(RXonly)
TheRXsupportsHotkeyforOSDMenu.YoucanchoosetheHotkey:enterRXOperationmode
Webpage‐‐‐>[Functions]‐‐‐>[Hotkey]‐‐‐>selecttheHotkeyof<Ctrl><Ctrl>,<Shift><Shift>,
<Alt><Alt>,or<Scroll><Scroll>(defaultCtrlCtrl).
ToEnable/DisableUSBoverIP(TXonly)
EnterTXOperationmodeWebpage‐‐‐>[Functions]‐‐‐>[USBoverIP]‐‐‐>[EnableUSBoverIP]‐‐‐>
check/unchecktoEnable/Disable(defaultEnable).
Autoselectmode:Autoselect“Activeonlink”ifunitisinUnicast,select“Activeperrequest”ifunit
isinMulticast.
Activeonlink:USBoverIPwillbeestablishedinsharingmodewhenTX/RXconnectionestablished.
Activeperrequest:USBoverIPcanbemanuallyrequestedinexclusivemode,theformerRXofthe
USBoverIPconnectionwillbestoppedifthecurrentrequestissucceeded.
ToEnable/DisableSerialoverIP,andselectOperationMode
EnterTX/RXOperationmodeWebpage‐‐‐>[Functions]‐‐‐>[SerialoverIP]‐‐‐>check/uncheckto
Enable/Disable(defaultEnable).
EnterTX/RXOperationmodeWebpage‐‐‐>[Functions]‐‐‐>[SerialoverIP]‐‐‐>[OperationMode]‐
‐‐>selectoptionsofType1,Type2,Type1guestmode,Type2guestmode(defaultType2).
Note:Type1ismainlyforUnicastapplicationwhereusercandynamicallylinkwithanytargetRX.
Type2ismainlyforMulticastapplicationwhereTXRS‐232willlinkwithallofconnectedRXs
(default).
Type1guestmodeissimilartotype1butusingPCtolinkwithRX’sRS‐232.
Type2guestmodeissimilartotype2butusingPCtolinkwithRX’sRS‐232.
Fordetails,pleasereferto“HowtoUseRS232overIP”manual.

TodefineRS‐232parametersforType2
EnterTX/RXOperationmodeWebpage‐‐‐>[Functions]‐‐‐>[SerialoverIP]‐‐‐>[BaudrateSetting
forType2]‐‐‐>selectBaudrate,Databits,Parity,Stopbits.(default115200,8‐n‐1)
AudioOutput(RXonly)
IftheTX’sinputaudioisHDMI,youcanselecttheAudiotobeoutputonLineOut:
EnterRXOperationmodeWebpage‐‐‐>[Functions]‐‐‐>[AudioOutput]‐‐‐>check“HDMIAudio
De‐Embedder”fortheaudiooutputtoLine‐Out.Click[Apply]tosavethesettingandreboot.
Multi‐ScreenSetting
ThesystemsupportsMulti‐ScreenfeatureforPCwithmultiplescreens.EachTX/RXcandefineits
associated2nd,3rd,4thTX/RXIP.So,whentheMainRXswitchestoanewTX,itsassociatedRXswill
alsobeswitchedtothatnewTX’sassociatedTXsautomatically.
EnterTX/RXOperationmodeWebpage‐‐‐>[Functions]‐‐‐>[Multi‐ScreenSetting]‐‐‐>thenenter
IPaddressfortheassociated2nd,3rd,4thTX/RXIP.
Thereisanoptionof“Mirror”,whenenabled,theassociatedRXswillconnecttothesameTXasthe
MainRXisconnecting.ThisenablesmultipleRXstodisplaythesameTXasasplitter.

Installation
2. Byfactorydefault,theUDP1000T/Rispre‐configuredwithUnicast,DirectConnectionand
JumboFrame.Itisconfiguredforone‐to‐oneaspairingconnection.Themaximumdistance
betweenTXandRXis170metersbyusingCAT6cable.
3. ConnectsRXDVI‐ItoHDMI/DVI/VGAscreenbyaDVI‐to‐HDMI/DVI‐to‐DVI/DVI‐to‐VGAcable.
4. TheRXwillgetEDIDfromscreenandsendtoTXduringconnectionwithTX.
5. TheRXwilldisplaythefollowingstart‐upmessageswhenpoweredon:
FW:15‐Nov‐18A5.3.4‐‐‐>Firmwareversion
LocalIP:10.0.29.72‐‐‐>RX’sIPaddress
RemoteIP:10.0.29.73‐‐‐>ConnectingTXIPaddress
ID:0020FE001122‐‐‐>RX’sMACaddress
ConnectionMethod‐‐‐>DirectConnection
6. AttachHDMI/DVIsource(PCorBlue‐Ray)totheTX’sDVI‐InthenpowerONtheTXunit.TheTX’s
GreenLEDwillblinkthenONindicatingreadyandwaitingforconnectionwithRX.
7. AslongasTX/RXconnectionestablished,bothofTXandRXAmberLEDwillstarttoblink
indicatingwaitforvideoinputsource(GreenLEDisON).
8. IfyouareusingPCasvideosource,itisrecommendedtocheckifthecorrectscreenEDIDshown
onPCgraphiccardcontrolpanel?
9. ActivatevideosourcewithaudiotoTX,thencheckifRXcorrectlydisplay.Inthisstep,both
GreenandAmberLEDshouldbeONindicatingtheunitisreadyandvideosourceisalsoready.
USBandKMoverIPinstallation:
10. ConnectTXUSB‐BtoPC,OSwilldetectaGenericUSBVirtualHubDevice.
11. Thesystemcansupportboth“USB‐over‐IP”and“KM‐over‐IP”.
TheUSB‐over‐IPworksasaVirtual5‐portHUBwhenconnectedtoTX,itiscompatiblewithmost
kindofUSBdevicessuchaskeyboard,mouse,PenDrive,TouchScreen…TheUSB‐over‐IP
connectioncanbeconfiguredin“Activeonlink”(Sharing)modeorin“Activeperrequest”
(Exclusive)mode(default).In“Activeonlink”mode,themaximumUSB‐over‐IPconnectionfora

TXis5duetothe5portsofVirtualHUB.TheKM‐over‐IPmeansthatportwillworkasHID
deviceonlyforkeyboard/mouseemulation,thePCdon’tgetBIOS“KeyboardError”ifthereisno
realkeyboardattachedduringbootup.ItisnotnecessarytogainUSBaccessrightfortheKM‐
over‐IPport.TheTX(PC)canbesharedwithmultipleRXsforkeyboard/mouseaccessinKM‐
over‐IPmode.
12. Thereare3USB‐AportsontheRX.ThefactorydefaultsettingfortheTXisbothofUSB‐over‐IP
andKM‐over‐IPenabled,all3USBportsofRXareinUSB‐over‐IPmode(KM‐over‐IPdisabled).
13. Thereare2methodstogaintheaccessrightforaUSB‐over‐IPport:
12.1 Longpress(3sec.)theRX[Linkbutton]
12.2 Press“U”keytotoggleduringTransmitterListOSDmenu.
TheRXdisplay“RequestingUSB”toindicatestartingUSB‐over‐IPconnection,andmessageof
“StartingUSB”willbedisplayedifitsuccessfullygainedtheUSBaccessright.Meanwhile,the
previousUSBMasterunitwillshowanOSDmessageof“USBStopping”.

RXOSDMainMenu
TheRXsupportsOSDmenu,presstheRX’s[Link]buttontogettheOSD
Mainmenu:[HotkeySetting]and[ConnectionMethod].
RXOSDHotkeyselectionSub‐Menu
FromtheOSDMainMenu,press[Link]buttonto
movethehighlightarrowto[HotkeySetting].Waita
fewseconds,thesub‐menuwillshowupwith4
possibleselections:“CtrlCtrl”,“ShiftShift”,“AltAlt”,
or“ScrollScroll”.Press[Link]buttonagaintomove
thehighlightarrowtothedesiredselection.TheRX
unitwillbere‐booted.
RXOSDConnectionMethodSub‐Menu
FromtheOSDMainMenu,press[Link]buttontomovethe
highlightarrowto[ConnectionMethod].Waitafewseconds,either
theMulticastorUnicastConnectionMethodsub‐menuwillshowupdependingontheRX’s
Multicast/Unicastsetting:
TheMulticastRXsupports3possibleconnectionmethods:4‐bitsDIPxxxx,MulticastIP,
TransmitterList,astherightpicture:
The4‐bitsDIPxxxxmeanstheRXwillconnecttothesame4‐bitsDIPofTX.The
MulticastIP225.0.100.000meanstheRXwillconnecttotheTXwiththesame
MulticastIP.TheOSDTransmitterListmeanstheRXwillshowuptheavailable
Transmittersforusertoselectwhen<Hotkey><Hotkey>ispressed.

TheUnicastRXsupports2possibleconnectionmethods:OSDTransmitterList,DedicatedTXIP,
astherightpicture:

Pressthe[Link]buttontomovethehighlightarrowtothedesiredselectionandwaitawhileto
confirmtheselection.PleasenotetheSub‐Menuonlyprovideselection,theMulticastIPorTXIP
canonlybechangedbytheWebpagesetting.



RXOSDTransmitterList
AttachakeyboardtotheRX’sanyUSBport,thenpress<hotkey>
<hotkey>.TheTransmitterListwithmaximum8Transmitterswill
beshown,astheright‐handpictureindicates,thetopline“TX01(1/2)”
meansthecurrentconnectionis“TX01”andthereare2pagesand
currentlyit’sonpage1.TheTXwithanasterisk(*)markindicatesthecurrentconnectedTX.
1. YoucanselectTXbythe↑↓←→keyand<Enter>,or1~8keytoimmediatelyconnecttothat
TX.
2. PressF5torefreshTransmitterList.
3. PressUtorequest(orrelease)USB‐over‐IP.
4. ToendofOSD,press<ESC>

