ICRealtime EL-470 User manual

Operating Manual
USER'S INSTRUCTIONS
Vandal-proof Dome DNR Day / Night
Weatherproof Camera User’s Manual
Products : EL-470

2
USER’S MANUAL

3
USER’S MANUAL
Contents
◑General Features
◑Installing & Adjusting
◑ Dimension & Specification
◑OSD Control Button
◑Camera Menu Set Up
1. Menu Set Up
2. Lens Setting
3. Exposure Setting
4. White Balance Setting
5. SSDR Setting
6. Backlight Setting
7. DNR3 Setting
8. Day/Night Setting
9. Special Setting
10. Exit Setting
◑Trouble Shooting
4
5
6
7
8
8
9
10
11
12
13
14
15
19
20

4
USER’S MANUAL
General Features
◑ Ultra High Sensitivity
- The built-in high sensitivity COLOR CCD produces a clear image even in 0Lux(B/W, IR-LED ON)
or lower illumination.
◑ 600TV Lines
-
By adopting a diagonal 6mm(1/3") 410,000 (NTSC) pixel, 470,000(PAL) pixel SONY CCD,
the camera produces clear picture quality with a horizontal resolution of 600 TV lines for
color and a horizontal resolution of 700TV lines for BW mode.
◑ DNR3
- The high-performance W-V DSP chip effectively removes low-light gain noise and
ghosting to
provide clear images even in dark environments.
◑ Day & Night
- This camera has a function that automatically selects the mode that is appropriate for
daytime or night-time conditions. The COLOR mode operates in daytime conditions to
provide optimum colors, and BW mode operates in night-time conditions to enhance the
definition of the image.
◑ SSDR
- For images with high contrast between bright and dark Areas from difficult lighting conditions
such as backlighting, this camera selectively illuminates darker Areas while retaining the same
light level for brighter Areas to even out the overall brightness.
◑ Miscellaneous Functions
- HLC(High Light Compensation), SENS-UP, FLIP(H/V-REV), D-ZOOM, SHARPNESS, MOTION
DETECTION and PRIVACY functions are provided.
◑ Disk Saving Effects
- Up-most and advanced DNR technology camera picture quality has a disk saving effects due
to
Image sizes are smaller than standard CCTV camera image.
◑ Controlled by OSD Menu
- The camera can be controlled by selecting the menu text displayed on the monitor screen.

5
USER’S MANUAL
INSTALLING & COMPONENTS
1. Installation
- Using the L-wrench provided, loosen 4 screws by turning them and separate the dome cover
- Drill holes on the celling by matching to the holes on the case bed. Fix the case bed on the ceilling by
using tapping screws.
- Pass the power and video cable through the hole you want to pass them when mounting the main body
on the mounting bracket.
- Point a camera gimball to a desired derection and assemble a dome cover to the flush mounting base
with socket screws by using L-Wrench provided.
- Affix the mounting template to the mounting surface
2. Components
● CAMERA 1piece ● Instruction Manual 1piece ● Service Monitor Cable 1piece
● Tapping Screw 4pieces ● L-wrench 1piece
Ø5t apping screw x 4 (supplied) M4 Machine screw x 4 (supplied)

6
USER’S MANUAL
DIMENSION & SPECIFICATION
noitcennoC&noisnemiD.1
2. Specification
Dimension Connection
Model IR LED VANDAL DOME
IR LED ON : DC12V 650mA / AC24V 270mA
DC Auto Iris Varifocal Lens(2.8mm-12mm)
146mm(W) * 105mm(H) * 146mm(D)
1400g
Image Pick-Up Device
TV System
Total Pixels
Scanning Frequency
Scanning System
Synchronization
Resolution
Minimum Illumination
S/N Ratio
Video Output
Electronic Shutter Speed
OSD
SSDR
BLC
Day & Night
Gain Control
White Balance
SENS-UP
Motion Detection
Privacy Masking
DNR3 (Digital Noise Reduction)
Digital Zoom
DIS (Digital Image Stabilizadion)
Sharpness
Filp / Mirror
Power Supply
Power Consumption
Lens
Operational Temp.
Storage Temp.
Dimension
Weight
1/3” Sony Super HAD CCD
NTSC/ PAL
NTSC=811(H)*508(V) / PAL=795(H)*596(V)
2:1 Interlace
Internal
600TV Lines
IR LED OFF: 0.15 Lux, IR LED ON: 0.00002 Lux
More than 52dB
CVBS:1.0Vp-p / 75Ω
NTSC=(1/60sec~1/120,000sec)/ PAL=(1/50sec~1/120,000sec)
Available
On / O Level adjustable)
BLC / HLC / OFF
Color / BW / AUTO
Low / High /
ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~11,000°K)
Auto / OSelectable x2 ~ x512)
On / O Programmable Zones)
On / O Programmable Zones)
On / O Level adjustable)
On / O x1 ~ x16)
On /
On / O Level adjustable)
On /
DC 12V / AC 24V Dual Voltage
-10 ~ +50 Deg C. RH95% MAX.
-20 ~ +60 Deg C. RH95% MAX.
NTSC=768(H)*494(V)/ PAL=752(H)*582(V)
NTSC=15.734KHz(H), 59.94Hz(V) / PAL=15.625KHz(H) , 50.00Hz(V)

7
USER’S MANUAL
OSD Control Button
1. OSD button could be used when it needs to OSD control.
▲Up button: Moves the cursor upwards. Use this button to select an item
or adjust the parameters.
▼Down button: Moves the cursor downwards. Use this button to select an
item or adjust the parameters.
◀Left button: Moves the cursor to the left. Use this button to select or
adjust the parameters of the selected item. The parameter changes
each time this button is pressed.
▶Right button: Moves the cursor to the right. Use this button to select or
adjust the parameters of the selected item. The parameter changes each
time this button is pressed.
◎Set button: Executes selections and displays a submenu for an item with
the mark.

8
USER’S MANUAL
●
Menu Setup
●
Lens Setting
1. Press the Function Setup switch.
- Main setup menu is displayed on the monitor screen.
3. THE Lens mode has sub menu items as listed below.
- BRIGHTNESS : Adjusts the video brightness.
Using this function, you can control the screen brightness.
1. When the SETUP menu screen is displayed, select 'LENS' by using
the Function Setup switch so that the arrow indicates 'LENS'.
2. DC : You can adjust the LENS BRIGHTNESS and IRIS SPEED.
2. Select a desired function using the Function Setup switch.
- Place the cursor over a desired item.
3. Set up a selected item by using the Function Setup switch.
4.
To finish the setting, select 'EXIT' and press the Function Setup switch.
MAIN SETUP
MAIN SETUP
1.LENS
2.EXPOSURE
3.WHITE BAL
4.SSDR
5.BACKLIGHT
6.DNR3
7.DAY/NIGHT
8.SPECIAL
9.EXIT
1.LENS
2.EXPOSURE
3.WHITE BAL
DC
ATW
OFF
OFF
ON
AUTO
SAVE
DC
ATW
☞NOTE
■
An item with the
◀
icon also has sub menus. To select a sub menu, select an item
with the icon and press the Function Setup switch.
■
An item with the - - - icon is unavailable due to function settings.

9
USER’S MANUAL
- FOCUS ADJ : To adjust the DC lens focus correctly, you must activate the Focus Settings
mode under each lens menu. Activate the Focus Settings mode, adjust the lens focus, and
then deactivate the settings mode.
☞NOTE
■ If color rolling occurs when using a DC lens, set Shutter to Fixed (---).
☞NOTE
■ When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled.
●
Exposure Setting
1. When the SETUP menu screen is displayed, select 'EXPOSURE' by using the
Function Setup Switch.
2. Select a desired mode using the Function Setup switch.
◆ SHUTTER : You can select either auto or manual shutter.
* --- : Shutter speed is fixed at 1/60sec(1/50sec)
* ESC : Select this to control the shutter speed automatically. If ESC is selected, the shutter
speed is automatically controlled depending on the ambient illumination of the subject.
* MANUAL : You can control shutter speed manually.
(NTSC MODEL : 1/60~1/120,000, PAL MODEL : 1/50~1/120,000)
* A.FLK : Select this when you see picture flicker, this can happen when the frequency of the
local lighting clashes with the camera.
MAIN SETUP
1.LENS
2.EXPOSURE
3.WHITE BAL
DC
ATW
EXPOSURE SETUP
1.BRIGHTNESS
2.SHUTTER
3.AGC
4.SENS-UP
5.RETURN
25
- - -
HIGH
OFF

10
USER’S MANUAL
◆
AGC(AUTO GAIN CONTROL) : The higher the gain level, the brighter the screen
but the higher the noise.
* OFF : Deactivates the AGC function.
* LOW : Allows automatic gain control from 5.3dB to 32dB.
* HIGH : Allows automatic gain control from 5.3dB to 37dB.
◆
SENS-UP : When it is night or dark, the camera automatically detects the light
level and maintains a clear picture if this mode is activated.
* OFF : Deactivates the SENS-UP function.
* AUTO : Activates the SENS-UP function.
◆
RETURN : Select this to save the changes in the EXPOSURE menu and
return to the SETUP menu.
☞NOTE
■ If you press the Function Setup switch to ‘AUTO’ mode, you can adjust brightness by
increasing or decreasing the shutter speed. (x2 ~ x512)
■ Note that the higher the zoom level, the brighter the screen, but the more likely there
will be a ghosting effect.
■ It is normal for Noise, Spots and Whitish symptoms to appear in SENS-UP mode when
the D-ZOOM level is increased.
●
White Balance (White Bal) Setting
Use the White Balance function to adjust the screen color.
1. When the SETUP menu screen is displayed, select 'White Bal' by using the Function
Setup switch so that the arrow indicates 'White Bal'.
2. Select a desired mode using the Function Setup switch.
MAIN SETUP
1.LENS
2.EXPOSURE
3.WHITE BAL
DC
ATW