ICRealtime HD-AVS User manual

Quick Start Guide
HD-AVS Dome
Cameras
Features and Specifications
A. Overview
B. Cable Interface
Camera Installation
A. Installation Steps
B. Lens Adjustment
C. Waterproofing Connectors
FAQ and Lightning Protection
A. FAQ
2
2
3-4
4
4
5
Table Of Contents
MARGIN
GUIDES
To see the guides to go:
View / Guides / Show
Guides
www.icrealtime.com
IMPORTANT SAFEGUARDS AND WARNINGS
Electrical Safety
All installation and operation here should conform to your local electrical safety codes. The
power shall conform to the requirement in the SELV (Safety Extra Low Voltage). Please check
product specifications for power requirements. We assume no liability or responsibility for all
the fires or electrical shock caused by improper handling or installation. We are not liable for
any problems caused by unauthorized modification or attempted repair.
Transportation Security
Care must be given to avoid heavy stress, violent vibration or water damage during
transportation, storage and installation.
Installation
Do not apply power to the camera before completing installation. Please install the proper
power cut-off device during the installation connection. Always follow the instruction guide the
manufacturer recommended.
Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers. We are
not liable for any problems caused by unauthorized modifications or attempted repair.
Environment
This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc. Please keep it away from the electromagnetic
radiation object and environment. Please make sure the CCD (CMOS) component is out of the
radiation of the laser beam device. Otherwise it may result in CCD (CMOS) optical component
damage. Please keep the sound ventilation. Do not allow the water and other liquid falling into
the camera. Lightning-proof device is recommended to be adopted to better prevent lightning
damage. The grounding studs of the product are recommended to be grounded to further
enhance the reliability of the camera.
Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily
maintenance work. Do not touch the CCD (CMOS) optic component. You can use the blower to
clean the dust on the lens surface. Always use the dry soft cloth to clean the device. If there is
too much dust, please use the water to dilute the mild detergent first and then use it to clean
the device. Finally use the dry cloth to clean the device. Please put the dustproof cap to protect
the CCD (CMOS) component when you do not use the camera.
Accessories
Be sure to use all the accessories recommended by manufacturer. Before installation, please
open the package and check all the components are included. Contact your local retailer ASAP
if something is broken in your package.

1A. OVERVIEW
This series Dome style camera utilizes High Definition Advanced
Video System (HD-AVS) technology, an HD-over-coaxial cable
video standard that allows long-distance, HD transmission of
video, audio, and control functions. Most camera models support
CVBS with an additional output.
The camera supports the IR night vision function. In the night
environments, the device can use the IR light to highlight the
object which is suitable for the surveillance function in the low
illumination environments. The waterproof design conforms to the
IP67 level and some models offer IK10 rating, thus is suitable for
use in outdoor environments.
1B. Cable Interface
See Figure 1-1 for cable interface identification. Outputs may vary
depending on model.
1. DC Power input (please see your specific model’s power
requirements)
2. Video output
3. Audio input (RCA)
4. Dip Switch (Changes video formats eg: CVBS, AVS, TVI)
Figure 1-1
MARGIN
GUIDES
To see the guides to go:
View / Guides / Show
Guides
2 | www.icrealtime.com

2A. INSTALLATION STEPS
MARGIN
GUIDES
Stay within the yellow
box. Do not let text go
beyond, instead move
to the next column or
start a new page.
3 | www.icrealtime.com
Step 1 Use the included position map and drill the appropriate
mounting holes and cable exit, if necessary. See Figure 2-1.
Step 2 Install the expansion screws. See Figure 2-2.
Figure 2-1
Figure 2-2
Figure 2-3
Figure 2-4
Step 3 Use the wrench included with the camera to remove the Dome
cover screws on the camera base. Thread the cabling through cable
exit if necessary. Thread the installation screws through the camera
base and tighten as necessary. See Figure 2-3.
Step 4 Loosen the bracket screw to adjust camera angle as shown in
Figure 2-4.

MARGIN
GUIDES
Stay within the yellow
box. Do not let text go
beyond, instead move
to the next column or
start a new page.
4 | www.icrealtime.com
Figure 2-5
Step 6 Install the Dome cover. Remove the protective film on the lens.
See Figure 2-6.
Figure 2-6
2B. Lens Adjustment (available in some models)
Some models feature a zoom and focus adjustment. Remove the
Dome cover and locate the adjustment knobs as shown in Figure
2-7.
Figure 2-7
Figure 2-8
2C. Waterproofing Connectors
For outdoor installations, waterproofing the connectors is necessary.
See Figure 2-8.
Step 5 You can also adjust the camera rotation from the base as well as
the lens as necessary. See Figure 2-5.

MARGIN
GUIDES
Stay within the yellow
box. Do not let text go
beyond, instead move
to the next column or
start a new page.
8 | www.icrealtime.com
No image after the
Device is powered on
●Check whether the power supply is
properly connected.
●Check recorder video format and
resolution compatibility with Camera
●Check whether the main power and
transformer are working normally.
Image is black and
white
●Use the required power supply.
●Check recorder compatibility with
Camera video format
Cannot control zoom/
focus through the
recorder
●Insufficient power, use the required
power supply,
●Ensure PTZ settings on Recorder is
set to AVS protocol for that channel
Image is not stable ●Poor contact on circuits. Connect the
cable properly.
Blurry image.
●Lens glass is dirty. Clean the lens.
●Focus is in manual mode. Set Focus
settings.
3A. FAQ