ICRealtime F Series User manual

Vandal Proof IP Dome Camera User’s Manual
V1.1.1

Welcome
Thank you for purchasing our IP camera!
This user‟s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user‟s manual well for future reference!

Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
This series product uses DC 12V power. Please make sure your power sourcing equipment is right
before you boots up the device.
Before you replace the SD card, please unplug the power cable and then remove the shell
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Installation
Current series device has no power button. Please unplug all corresponding power cables before your
installation.
Do not apply power to the IP camera before completing installation.
Do not put object on the IP camera.
3．Environment
This series IP camera should be installed in a cool, dry place away from direct sunlight, inflammable,
explosive substances and etc.
Please keep the sound ventilation.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding studs of the product are recommended to be grounded to further enhance the reliability
of the camera.
4. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.
Use the dry soft cloth to clean the device.
If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean
the device. Finally use the dry cloth to clean the device.
5. Accessories
Please open the accessory bag to check the items one by one in accordance with the list below.
Contact your local retailer ASAP if something is missing or damaged in the bag.
Accessory Name
Amount
IPC Unit
1
12V power adapter
1
MD9M data converter cable
1
Accessories bag
1

Quick Start Guide
1
Warranty Card
1
Certificate Card
1
CD
1

Table of Contents
1General Introduction..............................................................................................................7
1.1 Overview ...................................................................................................................7
1.2 Features....................................................................................................................7
1.3 Specifications ...........................................................................................................8
1.3.1 Performance ......................................................................................................8
1.3.2 Function Specification.......................................................................................9
1.3.3 Factory Default Setup.....................................................................................11
2Structure ...............................................................................................................................15
2.1 Multiple-function Composite Cable.......................................................................15
2.2 Framework and Dimension ...................................................................................16
2.3 Bidirectional talk .....................................................................................................17
2.3.1 Device-end to PC-end.....................................................................................17
2.3.2 PC-end to the device-end...............................................................................17
2.4 Alarm Setup............................................................................................................18
3Installation ............................................................................................................................19
3.1 Device Installation..................................................................................................19
3.2 SD Card Installation...............................................................................................21
4Quick Configuration Tool ....................................................................................................24
4.1 Overview .................................................................................................................24
4.2 Operation ................................................................................................................24
5Web Operation.....................................................................................................................27
5.1 Network Connection...............................................................................................27

5.2 Login and Main Interface.......................................................................................27
6FAQ.......................................................................................................................................30

7
1General Introduction
1.1 Overview
This series IP camera integrates the traditional camera and network video technology. It adopts audio
and video data collection, transmission together. It can connect to the network directly without any
auxiliary device.
This series IPC uses standard H.264 video compression technology and G.711a audio compression
technology, which maximally guarantee the audio and video quality.
This series IPC enclosure has the strong resistance capacity, which can guarantee the proper work
performance under heavy strike. It supports real-time monitor and listening at the same time. It
supports analog video output and dual-way bidirectional talk.
It can be used alone or used in a network area. When it is used lonely, you can connect it to the
network and then use a network client-end. Due to its multiple functions and various uses, this series
IPC is widely used in many environments such office, bank, road monitor and etc.
1.2 Features
User
Management
Different user rights for each group, one user belongs to one group.
The user right shall not exceed the group right.
Storage
Function
Support central server backup function in accordance with your
configuration and setup in alarm or schedule setting
Support record via Web and the recorded file are storage in the client-
end PC.
Support local SD card hot swap, support short-time storage when
encounter disconnection.
Alarm
Function
Real-time respond to external local alarm input, wireless alarm input and
video detect( within 200MS) as user pre-defined activation setup and
exert corresponding message in screen and audio prompt(allow user to
pre-record audio file)
Real-time video detect: motion detect, camera masking, video loss.
Network
Monitor
IPC supports one-channel audio/video data transmit to network terminal
and then decode. Delay is within 500ms (network bandwidth support
needed)
Max supports 10 connections.
Adopt the following audio and video transmission protocol: HTTP, TCP,
UDP, MULTICAST and RTP/RTCP and etc.
Support web access, widely used in WAN.
Network
Management
Realize IPC configuration and management via Ethernet.
Support device management via web or client-end.
Peripheral
Equipment
Support peripheral equipment management, each peripheral equipment
control protocol and interface can be set freely.
Support serial port (RS232/RS485) transparent data transmission.
Power
External power adapter DC12V
PoE
Support Power over Ethernet (PoE). Conform to the IEEE802.3af
standard.
Connect the device to the switcher or the router that supports the PoE
function to realize the network power supply.

8
To guarantee proper performance, please make sure the power
sourcing device can supply at least 6.4W power for DB series product
and 10W power for DBW series product.
Assistant
Function
Log function
Support PAL/NTSC
Support system resource information and running status real-time
display.
Day/Night mode auto switch
Built-in IR light. Support IR night vision (For IR series only)
Backlight compensation: screen auto split to realize backlight
compensation to adjust the bright.
Support video watermark function to avoid vicious video modification.
1.3 Specifications
1.3.1 Performance
Please refer to the following sheet for IPC performance specification.
Parameter
Specification
DB/DBW625 Series
DB/DBW645 Series
DB/DBW665 Series
Camera
Sensor
Type
1/3-inch SONY Supper HAD CCD
Resolution
420TVL
480TVL
540TVL
Pixel
PAL：500（H）*582
（V）
NTSC：510（H）*492
（V）
PAL：752（H）*582（V）
NTSC：768（H）*494（V）
Lens Mode
M12*0.5
Video
Format
PAL/NTSC
Shutter
1/50（1/60）～1/1000005
Min.
Illumination
Color 0.5Lux/F1.2 B/W
0.05Lux/F1.2（IR mode
0Lux）
Color 0.3Lux/F1.2 B/W
0.03Lux/F1.2（IR mode
0Lux）
Color 0.1Lux/F1.2 B/W
0.01Lux/F1.2（IR mode
0Lux）
Auto Iris
N/A
Analog
Output
Supported
SNR
＞50dB
Video
Standard
PAL：1f/s～25f/s，NTSC：1f/s～30f/s
Encode
Capability
H.264 encode，5 CIF
Encode Bit
Stream
D1（704*576/704*480）
HD1（352*576/352*480）
CIF（352*288/352*240）
QCIF（176*144/176*128）

9
Video
Recording
Speed
PAL：1-ch 1f/s～25f/s adjustable
NTSC：1-ch 1f/s～30f/s adjustable
IR Distance
10~20M（For IR series product）
Network Capacity
Max support 10 network users to monitor simultaneously
TCP output capacity 75Mbps
UDP output capacity 85Mbps
Power Consumption
＜6W
Power
DC 12V
Temperature
-10℃～+50℃
Working Environment
Humidity
10%～90％
Dimension(H*W*D）
141.4mm*141.4*111.5mm
1.3.2 Function Specification
Please refer to the following sheet for function specification information.
Specification
Note
CCD Video
Process
Backlight compensation
control
Auto
White balance
adjustment
Auto
Contrast ness adjustment
Auto
Bright ness adjustment
Auto
Electronic shutter control
Auto
Color/B&W(Day/Night)
switch
Auto
Note
The color/B&W (Day/Night) switch here just an electronic switch.
System removes the color elements and reserves the B&W
elements. It is not a filter switch.
Video
Resolution
D1/HD1/CIF/QCIF
Video compression
Standard H.264 encode/decode format
d
Motion Detection
Take 18*22 pix as a macro unit. Support 396 detection zones.
Sensitivity level ranges from 1 to 6.
Dual-stream
1-channal real-time D1 + 1-channel CIF
Audio
Bidirectional Talk
Bidirectional talk. Delay within 200ms
Audio Listening
Audio listening. 1-ch MIC input.
Network
WEB access via IE browser.
PPPoE dial function
DHCP auto get IP address
DDNS
SMTP email function
NTP time synchronization.
DNS domain parse
IP address filter
IP address auto search function
Record
Schedule Record
Support max 6 periods. (This series product does not support this
function.)

10
Manual Record
After enabling manual record, no matter system is in schedule or
alarm status or not, system just begins recording.
Alarm Record
System automatically enables recording function when alarm
occurred.
Motion Detection Record
When video changes, system automatically enables record
operation.
OSD
Time Title Display
There are 255 layers.
O is the bottom layer and 255 is the highest layer.
O means completely transparent and 255 is opaque.
Channel Title Display
Please refer to the above information.
Privacy Mask
Max supports 8 zones.
Storage
Local Micro SD storage
Support high-speed card/low-speed card
Based on SDK network
storage
Supported
Alarm
Network alarm/local
alarm output
1-ch local/network alarm output
Local alarm/network
alarm input
2-ch local/network alarm input
Event
Management
Activate alarm via motion
detection or external
input
Please enable pre-record function when activating the alarm
Upload image email.
Upload automatically
Send out alarm notice via
email, HTTP and external
port.
Support de-jitter when alarm occurs frequently.
Support video short time
buffer storage before or
after alarm
Pre-record is 2Mbytes. Buffer storage video of 5s.
Control
RS485 PTZ control
Support semi-duplex communication way.
On-line
Upgrade
Network remote upgrade
Use upgrade tool.
Device
Management
Network client-end
Log in the client-end software in the PC to monitor IPC.
Parameter
Configuration
IPC provides device information, video information, COM setup, record setup, motion detection
setup, alarm setup, OSD information interfaces to modify system setup.
IPC provides running information such as user port, log, status, user management, email setup,
date modification.
Log
System can record the important event log record
Record the following information：
System operation, setup operation, alarm event, record management, user management, clear
log.
Water Mark
To avoid vicious video modification.
Power
supply
DC12V power supply
RESET
Support hardware reset. System needs to reboot to activate the default setup.
Port ESD
protection
9-pin input and output port
Network port

11
12V power adapter
9-pin I/O Port
One analog video output port
One audio input port
One audio output port
Two alarm input port
One alarm output port
One network interface（RJ45 10M/100M self-adaptive Ethernet port）
Others
One red/green running status indication light.
One RESET conversion cable
IR light (For IR series product only)
Installation
Pendant installation
1.3.3 Factory Default Setup
Please refer to the following sheet for factory default setup information.
Function Configuration
Type
Item Name
Default setup
General Setup
Date format
Y-M-D
DST
Disable by default
Date separator
„ _ ‟
Time format
24H
Language
Simplified Chinese
When HDD is full
Overwrite
Record duration
60M
Device No.
8
Video type
PAL
Encode
Setup
Main
Stream
Channel
Channel01
Encode mode
H.264
Audio/Video enable
Enable audio and video
General bit stream
General bit stream
Resolution
D1
Frame rate
25
Bit stream control
VBR
Quality
Good
Bit stream value
2048
I frame interval control
50
Extra
Stream
Extension Stream
General bit stream
Audio/Video enable
Enable audio and video
Resolution
CIF
Frame rate
25
Bit stream control
VBR
Quality
Good
Bit stream value
512
I frame interval control
50
Image Color
Brightness:50
Contrast:50
Sautratioon:50
Hue:50
Watermark
Enable
Watermark: all
Watermark type: character

12
Watermark: DigitalCCTV
Privacy Mask
Never
Time title
Enable. OSD transparent :128
Channel title
Enable. OSD transparent :128
Record Setup
Channel
Ch01
Pre-record
5 seconds.
Time Setup
Start Time
0:00:00
End Time
23:59:59
Record
Period 1:Enable motion
detection/alarm
Snapshot
Period 1: Enable motion
detection/alarm
Week
Sunday
COM Setup
Option
COM01
Function
General
Data bit
8
Stop bit
1
Baud rate
115200
Parity
None
Network Setup
Ethernet
Port 01
DHCP
Disable
IP address
192.168.1.108
Subnet mask
255.255.0.0
Gateway
192.168.0.1
Device name
Device factory default name
TCP port
37777
HTTP port
80
UDP port
37776
Network user connection
amount
10
Network transmission QoS
Disable
Remote host
Multiple broadcast group
Enable
Disable
IP address
255.255.255.0
Port
36666
Email setup
Enable
Multiple DDNs
Disable
NAS setup
Disable
NTP setup
Disable
Alarm server
Disable
Alarm Setup
Event type
Local input
Alarm input
Input 01, disable
Type
Normal open
Setup
Period:
Start time 0:00:00
End time:23:59:59
Period 1:enable
Week: Sunday
Anti-dither
0 second
General output
Disable
Alarm latch
10 seconds
Record channel
1, enable
Record latch
10 seconds

13
Send email
Disable
PTZ activation
Disable
Event type: never
Address: 0
Snapshoot
Disable
Video Detection
Event type
Motion detection
Channel
Ch01, Disable
Sensitivity
3
Time period setup
Period:
Start time 0:00:00
End time:23:59:59
Period 1:enable
Week: Sunday
Anti-dither
5 seconds
General output
Disable
Alarm latch
10 seconds
Record channel
Disable
Record latch
10 seconds
Send email
Disable
PTZ activation
Event type: Never
Address: 0
Disable
Snapshot
Disable
PTZ Setup
Channel
Ch01
Protocol
DH-SD1
Address
1
Baud rate
115200
Data bit
8
Stop bit
1
Parity
None
Default and Backup
All
Disable
General
Disable
Encode
Disable
Record
Disable
COM
Disable
Network
Disable
Alarm
Disable
Video detection
Disable
Display output
Disable
Channel No.
Disable
Advanced
Record control
Auto. Ch1 (This series device does
not support this function.)
Abnormity
Even Type
No HDD, Disable
General
Output
Disable
Alarm Latch
10 seconds
Send email
Disable
User account
admin--- password: admin (reusable)
888888--- password: 888888(reusable)
666666--- password: 666666(reusable)
default--- password: tluafed
Snapshot
Channel
Ch01
Snapshot
mode
Scheduled
Frame rate
1f/s
Resolution
D1

14
Quality
60%
Auto
maintain
Auto reboot
2.00 each day
Auto delete
old files
Never
Camera Property
Channel
1
Exposure Mode
Auto
Day/Night Mode
Color
Backlight Compensation
Disable
Auto Aperture
N/A
N/A
Disable
Disable
White Balance
N/A
Signal Type
Internal input
Mirror
Disable
Disable
N/A
N/A
Flip
Disable
Disable
N/A
N/A
Auto Registration
Enable
Disable
SN
1
IP
0.0.0.0
Port
7000
Device ID
Dahua
DNS Setup
DNS
202.101.172.35
Alternative DNS
202.101.172.35
IP Filter
Disable

15
2Structure
2.1 Multiple-function Composite Cable
You can refer to the following figure for multiple-function composite cable information. See Figure 2-1.
Figure 2-1
Please refer to the following sheet for detailed information.
Port Name
Function
Connection
Note
VIDEO OUT
Video output
port
BNC
Output analog video signal. It can connect to the
TV monitor to view the video.
AUDIO IN
Audio input
port
RCA
Input audio signal. It can receive the analog audio
signal from the pickup.
AUDIO OUT
Audio output
port
RCA
Output audio signal to the devices such as the
sound box.
+12V DC
Power input
port
/
Power port. Input 12V DC
I/O
I/O cable port
/
Connect to MD9M data converter cable.
LAN
Network port
Ethernet
port
Connect to standard Ethernet cable.
Please refer to the follow sheet for detailed information of MD9M data converter cable.
Port Name
Cable
Color
Name
Note
I/O Port
Pin
Yellow
RS485_A
RS485_A port. It is to control the PTZ.
Black
RS485_B
RS485_B port. It is to control the PTZ.
Red
ALARM_COM
Alarm output public port.
Brown
ALARM_IN1
Alarm input port 1. It is to receive the on-off signal
from the external alarm source.
Grey
ALARM_IN2
Alarm input port 2. It is to receive the on-off signal
from the external alarm source.

16
Port Name
Cable
Color
Name
Note
White
ALARM_NO
Alarm output port. It is to output the alarm signal
to the alarm device.
NO: normal open alarm output port.
It works with the ALARM_COM port.
Blue
RESET
It is to restore factory default setup.
When the device is working properly, please
connect the blue cable (restore default setup port)
to the orange cable (GND signal) for 5 seconds,
the device can resume factory default setup.
Orange
GND
Ground port
2.2 Framework and Dimension
Please refer to the following two figures for dimension information. The unit is mm. See Figure 2-2 and
Figure 2-3.
Figure 2-2

17
Figure 2-3
2.3 Bidirectional talk
2.3.1 Device-end to PC-end
Device Connection
Please connect the speaker or the pickup to the first audio input port in the device rear panel. Then
connect the earphone or the sound box to the audio output port in the PC.
Login the Web and then enable the corresponding channel real-time monitor.
Please refer to the following interface to enable bidirectional talk.
Figure 2-4
Listening Operation
At the device end, speak via the speaker or the pickup, and then you can get the audio from the
earphone or sound box at the pc-end.
2.3.2 PC-end to the device-end
Device Connection

18
Connect the speaker or the pickup to the audio output port in the PC and then connect the earphone
or the sound box to the first audio input port in the device rear panel.
Login the Web and then enable the corresponding channel real-time monitor.
Please refer to the above interface (Figure 2-4) to enable bidirectional talk.
Listening Operation
At the PC-end, speak via the speaker or the pickup, and then you can get the audio from the earphone
or sound box at the device-end.
2.4 Alarm Setup
The alarm interface is shown as in Figure 2-5. Please follow the steps listed below for local alarm input
and output connection.
1) Connect the alarm input device to the alarm input port (grey or brown pin of I/O port cable).
2) Connect the alarm output device to the alarm output port (White-pin) and alarm output public port
(Red-pin). The alarm output port supports NO (normal open) alarm device only.
3) Open the Web, go to the Figure 2-5. Please set the alarm input 01 port for the brown-pin (the 1st
channel) of I/O port cable. The alarm input 02 is for the grey-pin (the 2nd channel) of I/O port cable.
Then you can select the corresponding type (NO/NC.)
4) Set the WEB alarm output. The alarm output port of the alarm output 01 device (The white-pin of the
I/O port cable).
Figure 2-5

19
3Installation
This series IPC can be put on the table to realize surveillance. Or you can use the bracket or the in-
ceiling installation to realize the hang function. Please refer to the steps listed below.
3.1 Device Installation
Step 1
Use the inner hexagonal wrench (provided) to loose the four inner hexagon screws in the dome cover
and then open the cover. See Figure 3-1.
Figure 3-1
Step 2
Put the camera lens facing the monitor area (The lens tilt angle ranges from 10 to 90 degrees). Please
make sure the U-slot centre surface of the black internal enclosure shall be vertical to the monitor area.
Draw out the cable exit and four screw holes in the installation position according to the device
pedestal. Dig the four plastic expansion bolt hole and cable exit. Insert the four plastic expansion bolts
into the screw holes
Step 3
Adjust the camera lens to the proper monitor angle and then draw the cable through the cable exit you
just dug in the ceiling (wall). Line up the four screw holes in the device pedestal to the four plastic
expansion bolt holes in the installation position. Put the four self-tapping screws in the device pedestal
and then use the screwdriver to secure the screws in the four plastic expansion bolts firmly. See
Figure 3-2.

20
Figure 3-2
Step 4
Put the dome cover back and then put the four inner hexagon screws into the holes. Use the inner
hexagonal wrench to fasten these four screws. See Figure 3-3.