Icron EL5363 User manual

EL5363 HDMI + USB 2.0 Extender
HDMI and USB 2.0 100m CAT 5e/6/7 KVM Extender System
User Guide

Thank you for purchasing the EL5363 KVM Extender.
Please read this guide thoroughly.
This document applies to Part Numbers: 00-00386, 00-00387, 00-00388, 00-00389, 00-00390
FCC Radio Frequency Interference Statement Warning
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received
including interference that may cause undesired operation.
CE Statement
We, Icron Technologies Corporation, declare under our sole responsibility that the EL5363, to which
this declaration relates, is in conformity with European Standard EN 55022, EN 61000, and EN 55024.
IC Statement
This Class A digital apparatus complies with Canadian ICES-003.
WEEE Statement
The European Union has established regulations for the collection and recycling of all waste electrical
and electronic equipment (WEEE). Implementation of WEEE regulations may vary slightly by individual EU
member states. Please check with your local and state government guidelines for safe disposal and recycling
or contact your national WEEE recycling agency for more information.
Product Operation and Storage
Please read and follow all instructions provided with this product, and operate for intended use only.
Do not attempt to open the product casing as this may cause damage and will void warranty. Use only the
power supplies provided with this product. When not in use, product should be stored in a dry location
between -20°C and 70°C.
©2016 Icron Technologies Corporation. All rights reserved. Icron Technologies Corporation, the Icron
Technologies Corporation logo, and the Icron Technologies Corporation products referred to herein are
either the trademarks or the registered trademarks of Icron Technologies Corporation. All other trademarks
are property of their respective owners. Icron Technologies Corporation assumes no responsibility for errors
that may appear in this manual. Information contained herein is subject to change without notice.
Document #90-01425-A02

Contents
Introduction ...................................................................................................................... 4
Product Contents...........................................................................................................................................................................4
Requirements..................................................................................................................................................................................4
About the EL5363 KVM Extender.............................................................................................................................................4
Compatibility and Recommended Setup ............................................................................................................................5
The LEX Unit....................................................................................................................................................................................6
The REX Unit....................................................................................................................................................................................7
Installation Guide ............................................................................................................. 8
Installing the LEX Unit ..................................................................................................................................................................8
Installing the REX Unit.................................................................................................................................................................8
Connecting the LEX to the REX................................................................................................................................................9
Connecting a USB device ...........................................................................................................................................................9
Powering the Extender System................................................................................................................................................9
Checking the Installation .........................................................................................................................................................10
Troubleshooting Guide .................................................................................................. 11
Specifications.................................................................................................................. 13
Contacting Technical Support ....................................................................................... 14
Warranty Information .................................................................................................... 14
Obtaining Warranty Service ..........................................................................................15
Technical Glossary..........................................................................................................16

Introduction
This guide provides product information for the EL5363 installation instructions, troubleshooting guidelines,
and instructions for contacting Icron regarding technical support and warranty information. The instructions
in this guide assume a general knowledge of computer installation procedures, familiarity with cabling
requirements and some understanding of USB devices.
NOTE provide additional information that could be useful.
CAUTIONS provide important information about an operational requirement.
Product Contents
Packaged with:
• LEX Unit (Local Extender)
• REX Unit (Remote Extender)
• (2) 5V DC power adapter
The product requires two power adapters, one for the LEX and one for the REX.
Requirements
To complete the installation, you will require the following items that are not included with the product:
• A computer that is USB compatible (with USB compliant operating system) and has a HDMI port
• USB 1.1 or 2.0 compatible device(s)
• A minimum CAT 5e Shielded Twisted Pair (UTP) cable with two CAT 5e/6/7 RJ45 connectors (if using
surface cabling),
OR
• A minimum of CAT 5e cabling with two information outlets and two CAT 5e patch cords with CAT 5e
RJ45 connectors (if using premise cabling)
While CAT 5e UTP is the minimum category of twisted pair cabling, for the best experience,
and to minimize interference and cross-talk, CAT 6a/7 STP is strongly recommended.
When using CAT 5e cabling, the layout and quality of your cable runs and connections becomes
extremely important. Please refer to the Cabling section on page 5 for more detailed information.
About the EL5363 KVM Extender
The EL5363 KVM Extender system incorporates ExtremeUSB® and HD Video technology, which enables
users to extend both HDMI and USB 2.0 up to 100 meters (330 feet). The following ExtremeUSB features are
included:
• Transparent USB extension
• True Plug and play; no software drivers required
• Works with all major operating systems: Windows®, OS X®, and Linux®
note
note
note
4
• USB 2.0 Cable
• HDMI Cable
• Quick Start Guide and Warranty Information

Compatibility and Recommended Setup
The product is compatible with many graphics cards, Operating Systems, and monitors supporting up to a
4K, 1080p and 1920 x 1200 resolution. However, there is no guarantee that all devices will be compatible with
the product as there are a number of dierent factors that may impact the operation of this KVM Extender.
This product supports both USB 1.1 and USB 2.0 devices. These devices include: keyboards, mice, ash
drives, printers, speakers and microphones. If uncertain whether your USB device(s) can be supported,
please contact Technical Support: icron.com/support.
Test any expected USB or video devices prior to a performing any large deployment. Some devices may
not be compatible with the EL5363.
HDMI Cables
Poorly terminated HDMI cables may result in damage to the devices they are connected to.
Please ensure that you use the HDMI cable provided with the product when connecting the LEX
(Local Extender) to the host computer and high quality HDMI cables for all other HDMI connections.
Cabling
Solid core Category 6a/7 STP cable with Category 6a/7 RJ45 connectors is recommended for best
performance. Using unshielded cabling may leave your signal more susceptible to interference
and noise which may result in poor video performance or reduced extension distance. Maximum
distance and product performance will be reduced in the presence of interference or coiled
extension cable.
Cable Type Electrical Interference Susceptibility
Solid Core CAT 5e/6 UTP High
Solid Core CAT 5e/6 STP Moderate
Solid Core CAT 6a UTP Moderate
Solid Core CAT 6a STP Low (Recommended)
Solid Core CAT 7 STP Low (Recommended)
If you are coiling unshielded cabling in your set-up, depending on the quality of the cable and how it
is coiled, the maximum distance may be reduced to 50m.
Host Operating Systems
• Windows®, OS X®, Linux®
USB Peripherals
• Keyboards&Mice•Printers•MassStorageDevices•Speakers•Microphones
HDMI Features
The EL5363 KVM Extender is compatible with the following HDMI features:
• Full uncompressed high denition 4Kp30, 1080p and 1920 x 1200 video resolutions
• Depthperceptionof2Dand3D•DeepColorandx.v.Color•LipSyncPass-through
• CECPass-through•HDCPPass-through 5
note

The LEX Unit
The Local Extender (LEX) connects to the computer using the supplied HDMI and USB cable.
It’s important to use the HDMI cable supplied with the product when connecting the LEX to the host
computer to ensure proper operation.
ITEM TYPE DESCRIPTION
1 Power LED (Green) Green Light: The system is powered and ready to use.
No Light: The system does not have power.
2 Link LED (Green)
Green Light: The LEX and REX are able to communicate with each other
across the link.
No Light: There is no communication between the LEX and REX.
3 USB LED (Green)
Green Light: The LEX and the host computer are communicating with each
other and working.
Blinking Green Light: The host computer has entered power saving mode.
No Light: The host and the LEX are not communicating or not connected.
4 Video LED (Green)
Solid Green Light: HDCP (digital rights management) content is being
transmitted.
Blinking Green Light: Video (non-HDCP) content is being transmitted.
No Light: There is no video being transmitted.
5 Config Reserved for use by Icron Technologies.
6 Link Port (RJ45) Accepts RJ45 connector for CAT 5e/6/7 cabling.
7 HDMI In Accepts HDMI connector for video input from the host computer.
8 Device Port (USB Type B) Used to connect the LEX unit to the host computer.
9 Power Port Connects to the AC power supply.
Power
Link
USB
Video
Local Extender
EL5363
HDMI InConfig 5V DCLink
6
Front View
Rear View
1 2 3 4
5 8 9
67

The REX Unit
The Remote Extender (REX) provides HDMI output to a monitor and three USB Type A ports for standard USB
devices. Additional devices may be connected by attaching USB hubs.
ITEM TYPE DESCRIPTION
1 Power LED (Green) Green Light: The system is powered and ready to use.
No Light: The system does not have power.
2 Link LED (Green) Green Light: The LEX and REX are able to communicate with each other
across the link.
No Light: There is no communication between the LEX and REX.
3 USB LED (Green) Green Light: The LEX and the host computer are communicating with each
other and working.
Blinking Green Light: The host computer has entered power saving mode.
No Light: The host and the LEX are not communicating or not connected.
4 Video LED (Green) Solid Green Light: HDCP (digital rights management) content is being
transmitted.
Blinking Green Light: Video (non-HDCP) content is being transmitted.
No Light: There is no video being transmitted.
5 Cong Reserved for use by Icron Technologies.
6 Link Port (RJ45) Accepts RJ45 connector for CAT 5e/6/7 cabling.
7 HDMI Out Accepts HDMI connector to the remote monitor.
8 Device Port (USB Type A) Accepts USB device(s).
9 Power Port Connects to the AC power supply.
7
Front View
Rear View
HDMI Out 5V DCLink
Power
Link
USB
Video
Remote Extender
EL5363
Cong
1 2 3 4
5 8 8 8 9
6 7

Installation Guide
Before you can install the product, you need to prepare your site:
DVI & USB
up to 100m CAT 5e/6/7
(STP recommended)
REXLEX
Computer Monitor
1. Determine where the computer is to be located and set up the computer.
2. Determine where you want to locate the remote desktop including the monitor, keyboard, mouse
and any other USB device(s).
3. If you are using surface cabling, the product supports a maximum distance of 100m (330 ft).
or
If you are using premise cabling, ensure the CAT 5e/6/7 cabling is installed between the two
locations,with CAT 5e/6/7 information outlets located near both the computer and the USB device(s),
and the total length, including patch cords is no more than 100m.
Installing the LEX Unit
1. Place the LEX unit near the computer.
2. Install the supplied USB cable to the USB port on the LEX, and an available USB 2.0/1.1 Type A Port on
the computer.
3. Install the supplied HDMI cable to the LEX (HDMI In), and an available HDMI Port on the computer.
4. Plug the 5V, 3A power adapter into a suitable AC outlet near the LEX.
Installing the REX Unit
1. Place the REX unit near the monitor and USB device(s) in the desired remote location.
2. Connect the REX (HDMI Out) to the monitor with a high quality HDMI cable.
3. Plug in your USB device(s) into the USB ports on the REX.
4. Plug the 5V, 3A power adapter into a suitable AC outlet near the REX.
8

Connecting the LEX to the REX
While unshielded cabling may be used, to ensure proper operation, it is recommended that solid core CAT 6a/7 STP
cabling be used to connect the local extender to the remote extender. The cabling must have a straight-through
conductor conguration with no crossovers and must be terminated with CAT 6a/7 connectors to qualify as CAT 6a/7.
With Surface Cabling:
1. Plug one end of the CAT 5e/6/7 cabling (not included) into the Link port (RJ45) on the LEX.
2. Plug the other end of the CAT 5e/6/7 cabling into the Link port (RJ45) on the REX.
With Premise Cabling:
1. Plug one end of a CAT 5e/6/7 patch cord (not included) into the Link port (RJ45) on the LEX.
2. Plug the other end of the patch cord into the CAT 5e/6/7 information outlet near the host computer.
3. Plug one end of the second CAT 5e/6/7 patch cord (not included) into the Link port (RJ45) on the REX.
4. Plug the other end of the second patch cord into the CAT 5e/6/7 information outlet near the USB
device(s).
Connecting a USB Device
1. Install any software required to operate the USB device(s). Refer to the documentation for the USB
device(s), as required.
2. Connect the USB device to the device port on the REX.
3. Check that the device is detected and installed properly in the operating system.
Powering the Extender System
1. Power the Local Extender with the included 5V AC adapter.
2. Power the Remote Extender with the included 5V AC adapter.
Use only the power adapters supplied with the product. Use of substitute adapters may cause permanent damage to
the system and will void the warranty.
note
9

Checking the Installation
1. On the LEX and REX units, check that the Power, Link, USB, and Video LEDs are on. If the Link LED is o,
then the cabling between the LEX and REX is not installed properly or is defective.
2. Check to see if the USB LED is on and the Video LED is blinking or on; if they are not this indicates there
is no USB data or video data. Check the HDMI and USB connections to the host computer, and the
HDMI connection to the monitor. Check to see if any USB devices are connected to the REX.
3. For Windows users, open Device Manager to confirm that the USB functionality of the EL5363 has
been installed correctly. Expand the entry for Universal Serial Bus controllers by clicking the “+” sign.
If the EL5363 has been installed correctly, you should find it listed as one “Generic Hub”.
To open Device Manager in Windows 10/8/8.1 or Windows 7:
Open the Start menu, right click on “Computer” then select: Manage >> Device Manager
4. For OS X users, open the System Proler to conrm that the EL5363 has installed correctly. In the
left hand column under Hardware,select“USB”and inspect the right hand panel. If the EL5363 has been
installed correctly, you should nd it listed as a“Hub”under the USB High-Speed Bus/USB Bus.
To open System Proler in OS X:
Open the Finder, select Applications, then open the Utilities folder and double click on the System Proler icon.
5. If the product is not displaying video or the EL5363 fails to be detected by your operating system,
please consult the Troubleshooting section of this guide.
10
note
note