IEI Technology ECA-100 User manual

ECA-100
Industrial Chassis for ATX/microATX SBC
Quick Installation Guide
Version 1.00
PACKING LIST
1 x ECA-100 chassis
1 x SATA cable
1 x Power cord
2 x Wall mount brackets
1 x Holder bracket
1 x Slide track
1 x Power housing

1
SAFETY INSTRUCTIONS
Warning! Read this installation guide before connecting the system to the power source.
Warning! To prevent the device from overheating, do not operate it in an area that exceeds the
maximum operating temperature described in the user manual came with the SBC.
Warning! Ultimate disposal of this product should be handled according to all national laws and
regulations.
SPECIFICATIONS
Construction Heavy duty metal
SBC Form Factor ATX/microATX
PSU 1U flex power supply
Drive Bays 1 x 3.5”/2.5” HDD/SSD
Expansion: 1 x 3.5”/2.5” HDD/SSD by the optional
ECA-HDD-KIT-R10
Cooling Fans 1
I/O Openings 2 x USB
6 x COM
Expansion Slots 7
Indicators 1 x Power LED, 1 x HDD LED
Buttons 1 x Reset button, 1 x Power switch
Installation Desktop, wall mount
Operating Temperature -20°C ~ 60°C
Operation Humidity 5% ~ 95%
Color Black
Dimensions (DxWxH) 365 mm x 291 mm x 162 mm
Operating Vibration MIL-STD-810F 514.5C-1
Operating Shock Half-sine wave 3G, 11ms, 100 shocks per axis
Weight (Net/Gross) TBD
COMPATIBLE SBC
Model No. SBC Type PCI PCle
x1 x4 x8 x16
IMBA-Q170-i2-R10 ATX 2 0 3 2 0
IMBA-H110-R10 ATX 6 0 0 0 1

2
IMBA-H810-R10 ATX 4 2 0 0 1
IMBA-Q870-i2-R10 ATX 4 1 1 0 1
IMBA-Q770-R10 ATX 3 2 1 0 1
IMBA-Q670-R30 ATX 4 1 1 0 1
IMBA-H610-R10 ATX 4 2 0 0 1
IMB-Q870-i2-R10 microATX 1 1 1 0 1
IMB-H810-i2-R11 microATX 2 1 0 0 1
IMB-Q770-R10 microATX 1 1 1 0 1
IMB-H810-i2-R10 microATX 2 1 0 0 1
IMB-H610A-R10 microATX 0 3 0 0 1
POWER SUPPLY OPTIONS
Type Model No. Watt
ATX
ACE-A615A-RS-R11 150W
ACE-A618B-RS-R10 180W
ACE-A622A-RS-R11 220W
ACE-A627A-RS-R11 270W
ACE-A630B-RS-R10 300W
DIMENSION DRAWING
The dimensions of ECA-100 are shown below (Unit: mm).

3
INSTALLATION STEPS
To install the ECA-100 chassis, follow the steps below:
Step 1: Remove chassis cover.
Step 2: Install motherboard.
Step 3: Install power supply unit.
Step 4: Install system fan.
Step 5: Install hard disk drive.
Step 6: Reinstall top cover.
Step 7: Install wall mount brackets.
The installation steps outlined above are described in detail below. Please refer to the
relevant section.
REMOVE CHASSIS COVER
Step 1: Remove the top cover. Loosen the two thumbscrews on the top panel, slide
the cover outward, and then lift the cover up gently.
Step 2: Remove the front panel. Remove nine screws from the front panel, two on
left panel, three on right panel and four on bottom panel.
MOTHERBOARD INSTALLATION
Step 1: Install the motherboard. Align the screw holes on the motherboard with
the standoffs on the bottom panel. Secure the motherboard with the screws as figure
shown below.

4
Step 2: Install the I.O shielding. Push the I.O shielding in the chassis.
POWER SUPPLY UNIT INSTALLATION
Step 1: Install the power supply bracket to the power supply. Secure the power
supply bracket to the power supply with the screws as figure shown below.
Step 2: Install the power supply to the chassis. Secure the power supply to the

5
chassis with the screws as figure shown below.
SYSTEM FAN INSTALLATION
Step 1: Install the system fan. Place the system fan inside the chassis and align
the retention screws holes on the system fan with the retention screw holes on the
chassis. Install the fan to the chassis with the screws as figure shown below.
-----------------------------------------------------------------------------------------------------------------
NOTE:
To correctly connect the system fan cable from the system fan to the motherboard,
please refer to the user manual that came with the motherboard.
-----------------------------------------------------------------------------------------------------------------

6
HARD DISK DRIVE INSTALLATION
Step 1: Attach the HDD to the HDD bracket. To do this, slide the HDD to the HDD
bracket and secure the HDD to the HDD bracket with four retention screws.
Step 2: Install the HDD bracket to the chassis. Install the bracket with HDD to the
chassis by aligning the bracket retention screw holes in the top of the HDD bracket
with the retention screw holes on the chassis. Secure the HDD bracket to the chassis
with the screws as figure shown below.
-----------------------------------------------------------------------------------------------------------------
NOTE:
The SATA cables from the installed HDD must be connected to the SATA connector
and SATA power connector on the motherboard before installing the top panel to the
chassis. To correctly connect these cables, please refer to the user manual that came
with the motherboard.
-----------------------------------------------------------------------------------------------------------------
FRONT PANEL CABLE CONNECTION
The following buttons and LEDs are on the front panel of the ECA-100 chassis.
1 x Power switch
1 x Reset button
1 x HDD LED
1 x Power LED
These components are all connected to the motherboard with cables. To correctly
connect these cables, please refer to the user manual that came with the

7
motherboard.
REINSTALL TOP COVER
Step 1: Install the bracket. Install the bracket to chassis and tighten the two screws
as figure shown below.
Step 2: Reinstall top cover. Reinstall the top panel to chassis and tighten the two
thumbscrews on the top panel.
WALL MOUNT BRACKETS INSTALLATION
Step 1: Install the wall mount brackets.Align the four retention screw holes in the
wall-mount brackets with the retention screw holes on the side of the chassis.
-----------------------------------------------------------------------------------------------------------------
NOTE:
There are two methods of mounting the ECA-100. The mounting methods are shown
below.
-----------------------------------------------------------------------------------------------------------------

8

IEI SUPPORT URL
https://new.ieiworld.com/en/online_support_form/index.php
COMPLIANCE
This equipment has been tested and found to comply with specifications for CE marking. If the user modifies
and/or installs other devices in the equipment, the CE conformity declaration may no longer apply.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a ClassA digital device, pursuant to
part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
According to the requirement of the WEEE legislation the following user information is provided to customers
for all branded IEI Electronics products subject to the WEEE directive.
This symbol on the product or on its packaging indicates that this product must not be disposed of with your
other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over
to a designated collection point for the recycling of waste electrical and electronic equipment. The separate
collection and recycling of your waste equipment at the time of disposal will help to conserve natural
resources and ensure that it is recycled in a manner that protects human health and the environment. For
more information about where you can drop o- your waste equipment for recycling, please contact your local
city office, your household waste disposal service or the shop where you purchased the product.
Headquarters
威強電工業電腦股份有限公司
IEI Integration Corp.
22161 新北市汐止區中興路 29 號
No. 29, Zhongxing Rd., Xizhi Dist.,
New Taipei City 22161, Taiwan
TEL: [phone]
FAX: [phone]
[email protected]om
www.ieiworld.com
America
IEI Technology USA Corp.
138 University Parkway, Pomona,
CA 91768, USA
Tel:[phone]
Fax:[phone]
[email protected]world.com
usa.ieiworld.com
China
威强电工业电脑 IEI Integration (Shanghai) Corp.
上海市闵行莘庄工业区申富路 515 号
No. 515, Shen Fu Rd., Xin Zhuang Industrial
Develop Zone, Shanghai, 201108, China
Tel:[phone]
Fax:[phone]
[email protected]om.cn
www.ieiworld.com.cn
Copyright ©2019 IEI Integration Corp. All rights reserved