iflo Trapini 2 User manual

ŸHang the unit on the wall mounting plates (3).
ŸLevel the unit using your spirit level and adjusting the screw on the bottom
of the hanging bracket (4).
ŸOnce level screw on the front of the hanging bracket to tighten the unit to
the wall (5).
Note: Full height vanity units stand on the floor so will come complete with
fitted legs. To adjust the legs, unclip the plinth from the legs and adjust the
legs to the desired height (6). Replace the plinth.
3 4
5 6
Vanity Unit
Installation Instructions
We have taken great care to ensure that this product reaches you in perfect
condition. However should any parts be damaged or missing, please contact your
point of purchase. This does not affect your statutory rights.
In addition, if you require replacement parts your point of purchase will be happy
to assist.
Care and Maintenance
ŸThis furniture is made of wood and has a water resistant finish. It should not be left wet.
ŸThe quality of the finish is best maintained if it is wiped with a dry cloth after use.
ŸIt should only be cleaned using a soft damp cloth followed by a dry cloth.
ŸDo not use bleach or any abrasive cleaner.
Step 2 - Hang Unit
Important: Ensure all cutouts for plumbing are carried out prior to
installation.
Install the unit first before fitting the door following the instructions
supplied with the unit.
to the door/drawer front.
Please note: Images are for illustration purposes only.

ŸDecide on the height of the vanity unit and use a spirit level to draw a horizontal
guideline (1).
ŸMark out the internal dimensions of the unit making sure the plates are within
the internal dimensions of the unit by 2-3 mm.
ŸUsing a cordless drill along with the wall plugs and screws provided, fix the
plates in place (2).
ŸIf the wall is not solid, you will need to use your own fixings. Ensure that they are
adequate to support the total weight of the unit as stated on the packaging.
Please read this leaflet carefully before attempting to fit the doors to the unit.
This leaflet contains information which must be made available to the end user.
Please check the product for imperfections before fitting the doors.
Contact your point of purchase if an imperfection is found.
ŸHandle product with care.
ŸWhen drilling walls, check first for hidden pipes and cables.
ŸUse safety eyewear when drilling.
ŸKeep all small parts away from children.
ŸIf the product is over 25 kg (see packaging), 2 people are required to
carry and install the unit.
General Safety Instructions
Fixings and Fittings Supplied
Tools Required (not supplied)
ŸPosidrive Screwdriver ŸPower Drill, 2.5mm, 5mm Bits
x 1 per unit
(snap apart)
x 6 x 6
ŸLevel
ŸPencil ŸTape
measure
ŸHammer
Step 1 - Wall Fixings
1
2

C
We have taken great care to ensure that this product reaches you in perfect
condition. However should any parts be damaged or missing, please contact your
point of purchase. This does not affect your statutory rights.
In addition, if you require replacement parts your point of purchase will be happy
to assist.
Care and Maintenance
ŸThis furniture is made of wood and has a water resistant finish. It should not be left wet.
ŸThe quality of the finish is best maintained if it is wiped with a dry cloth after use.
ŸIt should only be cleaned using a soft damp cloth followed by a dry cloth.
ŸDo not use bleach or any abrasive cleaner.
Step 4 - Adjustments
Install the unit first before fitting the drawer fronts following the
instructions supplied with the unit.
Please note: Images are for illustration purposes only.
Drawer Front
Installation Instructions
Standard Drawer Deep Drawer with Rails
Drawer Front Removal
ŸFit the drawer box into the unit by placing on the runners and pushing back until it
clicks into place.
ŸIf the drawer front needs adjustment, remove the cover and alter as shown in the
illustrations (6).
ŸDeep drawers only- twisting the drawer rails will change the tilt of the drawer front (7).
ŸThe drawer front is removed by twisting a screwdriver in the middle screw 90°
anticlockwise (8).
Vertical Adjustment Horizontal Adjustment
Rail Adjustment
C
6
7 8

2
Please read this leaflet carefully before starting to fit the drawer fronts to the unit.
This leaflet contains information which must be made available to the end user.
Please check the product for imperfections before fitting the drawer fronts.
Contact your point of purchase if an imperfection is found.
ŸHandle product with care.
ŸWhen drilling walls, check first for hidden pipes and cables.
ŸUse safety eyewear when drilling.
ŸKeep all small parts away from children.
ŸIf the product is over 25 kg (see packaging), 2 people are required to carry and
install the unit.
General Safety Instructions
Fixings and Fittings Supplied
Tools Required (not supplied)
ŸPosidrive Screwdriver
ŸExcept for 400 vanity units, there are no separate fittings supplied as the
drawer clips and sides and cabinet are supplied complete with all fittings.
ŸRemove drawer front from packaging and place on a flat surface.
ŸEnsure that the drawer clips are securely attached to the drawer front using a posidrive
screwdriver (1).
Step 1 - Secure Drawer Clip
1
ŸFlat Blade Screwdriver
Step 2 - Deep Drawers only- Fit Drawer Rails
ŸPush the plastic dowel on the drawer rails into the drawer front and bring the rail
upright to lock (2).
ŸSlide the cover over the clip (3).
C
Step 3 - Attach the Drawer Front to the Drawer Box
ŸAlign the drawer clips with the sockets in the drawer box and push the drawer front on
to the drawer box until it clicks into place (4).
ŸDeep drawers only- clip the drawer rails into the bracket at the back of the drawer (5).
3
4 5