iflo 898051 User manual

1 x Solas dimmable LED mirror
600 x 500mm
Code: 898051
COMPONENTS
1 x Mirror.
Screws and spacers aached
TOOLS REQUIRED
1 x instrucons 2 x screws and plugs Pencil Screw driver
DIMENSIONS:
Height: 600mm
Width: 500mm
Depth: 40mm
Stud detector
IMPORTANT SAFETY
INFORMATION:
Please read these instructions carefully before
attempting to install this product. It is advisable to
keep these instructions in a safe place for
future reference.
We recommend that you consult a qualified
electrician. All electrical installations must be
carried out in accordance with current IEE wiring
regulations (BS7671).
lThis product must not be modified as it may
invalidate the warranty and may render the
product unsafe.
lThis product is only suitable for connecting to a
240V 50Hz supply.
lBefore commencing installation or maintenance,
isolate the main electrical supply for the
appropriate circuit at the fuse board.
lThis product should be used indoors only and
can be mounted portrait or landscape.
lThis mirror should be installed on a smooth flat
secure surface.
lThe wall fixings supplied are only suitable for
brick walls. for any other wall substrate please
purchase alternative wall fixings.
lWhen installing please take care to avoid water
pipes, joints and electrical cables.
lDo not exceed or stretch the cable length of
each LED wire.
lThis mirror contains 243 0.07W LED’s, please
test that they are working correctly before
hanging.
CARE AND MAINTENANCE:
lEnsure that the power is disconnected prior
to cleaning.
lTo maintain the finish of this product, clean with
a soft cloth periodically.
lDo not use harsh chemical solvents, as this may
discolour or damage the finish.

This mirror is IP44 rated
therefore suitable for
installation in zone 2 and the
outside zones.
ZONE
0Inside the bath or
shower. Must be SELV
(12V max) due to water
submersion.
225cm above the bath
or shower.
1
The area stretching to
60cm outside the bath
or shower and 60cm
from water outlet
of sink.
2
Technical drawings are for illustration purposes only.
Make sure you check all hole cut outs before work commences.
INSTALLATION
Carefully lift the mirror from the
packaging and position it onto a soft
flat surface to avoid scratching
the mirror.
The mirror must be installed with
a minimum clearance of 150mm
between the infrared sensor and any
adjacent countertop or obstruction
to ensure correct function of the
sensor. Mark the position of the fixing
holes in the metal bracket onto the
wall using a stud detector to ensure
you avoid any wiring or water pipes.
Ensure you isolate the main electrical
supply for the appropriate circuit
1 2
Outside Zones.
Anywhere outside zones 0, 1 & 2.
Where water jets are not used for cleaning
purposes, the general rules of BS7671 apply.
at the fuse board. This product is a
class 1 product and requires an earth
connection.
Mark the desired height of the mirror.
Drill the required holes and insert the
wall plugs. Note: Wall plugs supplied
are only suitable for solid/brick walls.
Please ensure the screws are
fully tight.
Using a flat-bed screwdriver, securely
connect to the mains supply using
the terminal block (incoming Neutral
(blue/black) to Neutral blue and
incoming Live (brown/red) to Live
brown).
To connect the LED’s attach the
male and female connectors. For the
demister pad, connect the remaining
male and female connectors together.
Attach the front glass panel safely
onto the metal back box mounted on
the wall. Secure tightly using the 2
screws and spacers.
Switch on the mains electrical supply.
To activate the mirror, swipe you hand
under the sensor switch.
Waste Electrical & Electronic Equipment (WEEE)
The symbol on the product, or on the document accompanying the product, the
crossed out wheelie bin symbol, indicates that this product may not be treated
as household waste. Instead it shall be handed over to the applicable collection
point for the recycling of electrical and electronic waste.