IFM Electronic DTE101 User manual

Operating instructions
RFID evaluation unit
DTE101
80005398 / 01 06 / 2016
UK

2
Contents
1 Preliminary note���������������������������������������������������������������������������������������������������4
1�1 Notes on this document���������������������������������������������������������������������������������4
1�2 Symbols used ������������������������������������������������������������������������������������������������4
2 Safety instructions �����������������������������������������������������������������������������������������������4
2�1 General����������������������������������������������������������������������������������������������������������4
2�2 Installation and connection ����������������������������������������������������������������������������4
2�3 Tampering with the device �����������������������������������������������������������������������������5
3 Functions and features ����������������������������������������������������������������������������������������5
3�1 Configuration via Ethernet interface ��������������������������������������������������������������5
3�2 RFID antennas ����������������������������������������������������������������������������������������������6
4 Function���������������������������������������������������������������������������������������������������������������6
5 Installation������������������������������������������������������������������������������������������������������������6
5�1 Installation distance ���������������������������������������������������������������������������������������6
5�2 Installation orientation������������������������������������������������������������������������������������7
5�3 Mounting options �������������������������������������������������������������������������������������������7
5�3�1 Mounting on DIN rail�����������������������������������������������������������������������������7
5�3�2 Removal �����������������������������������������������������������������������������������������������8
5�3�3 Mounting plate ��������������������������������������������������������������������������������������8
6 Electrical connection��������������������������������������������������������������������������������������������9
6�1 AUX voltage supply ��������������������������������������������������������������������������������������9
6�2 Field bus connection PROFINET IO Port 1 / Port 2�������������������������������������10
6�2�1 Factory setting of the Ethernet parameters ����������������������������������������10
6�3 Process connections IO-1 ��� IO-4 ��������������������������������������������������������������� 11
6�4 Functional earth connection� �����������������������������������������������������������������������12
6�4�1 Mounting on DIN rail���������������������������������������������������������������������������12
6�4�2 Mounting plate ������������������������������������������������������������������������������������12
7 Operating and display elements ������������������������������������������������������������������������13
7�1 Reset to factory settings ������������������������������������������������������������������������������13
7�2 LED indicators ���������������������������������������������������������������������������������������������13
7�2�1 LED AUX ��������������������������������������������������������������������������������������������13
7�2�2 LED PROFINET Port 1 / Port 2 ����������������������������������������������������������14
7�2�3 LED SF �����������������������������������������������������������������������������������������������14
7�2�4 LED BF �����������������������������������������������������������������������������������������������15

3
UK
Licences and trademarks
Microsoft® und Internet Explorer® are registered trademarks of Microsoft Cor-
poration� All trademarks and company names are subject to the copyright of the
respective companies�
7�2�5 LEDs IO1 ��� IO4 ���������������������������������������������������������������������������������15
7�2�6 Special device- LED indications ���������������������������������������������������������17
8 Technical data����������������������������������������������������������������������������������������������������17
8�1 Data sheets �������������������������������������������������������������������������������������������������17
8�2 Device manual���������������������������������������������������������������������������������������������17
9 Maintenance, repair and disposal����������������������������������������������������������������������18
10 Approvals/standards ����������������������������������������������������������������������������������������18
11 Scale drawing ��������������������������������������������������������������������������������������������������18

4
1 Preliminary note
1.1 Notes on this document
This document applies to the RFID evaluation unit DTE101�
It is part of the device and contains information about the correct handling of the
product�
This document is intended for qualified electricians� These specialists are people
who are qualified by their training and their experience to see and to avoid pos-
sible hazards that may be caused during operation of the device�
Read this document before use to familiarise yourself with operating conditions,
installation and operation� Keep this document during the entire duration of use of
the device�
1.2 Symbols used
►Instructions
> Reaction, result
[…] Designation of pushbuttons, buttons or indications
→Cross-reference
Important note
Non-compliance can result in malfunction or interference�
Information
Supplementary note
2 Safety instructions
2.1 General
►Observe these operating instructions�
►Adhere to the warning notes on the product�
Non-observance of the instructions, operation which is not in accordance with use
as prescribed below, wrong installation or incorrect handling can affect the safety
of operators and machinery�
2.2 Installation and connection
The device must only be installed, connected and put into operation by a qualified
electrician as the safe function of the device and machinery is only guaranteed
when installation is correctly carried out�The installation and connection must

5
UK
comply with the applicable national and international standards� Responsibility lies
with the person installing the device�
This is a class A product� The device may cause radio interference in
domestic areas� In this case it can be necessary for the user to take ap-
propriate measures�
2.3 Tampering with the device
Tampering with the device is not allowed and will lead to an exclusion of liability
and warranty� Tampering with the device can affect the safety of operators and
machinery�
►Do not open the device�
►Do not insert any objects into the device�
►Prevent metal foreign bodies from penetrating�
3 Functions and features
The RFID evaluation unit DTE101 integrates a PROFINET IO interface and 4
channels for the connection of field devices� Each channel can be used either for
the connection of an RFID antenna or as input/output to IEC 61131�
The device
• controls the data exchange to the RFID antennas or the sensor/actuator level�
• communicates with the higher-level control level via PROFINET IO�
• allows device configuration via a web server�
Application examples:
• Material flow control in production lines
• Warehouse management by the automatic detection of stored products
• Tank management, order picking or product tracking
3.1 Configuration via Ethernet interface
• 10 Mbps and 100 Mbps
• TCP / IP - Transport Control Protocol / Internet Protocol
• UDP - User Datagram Protocol
• IT functionality: HTTP server
• M12, twisted pair

6
3.2 RFID antennas
The device supports up to four RFID read/write heads of type ANT41x / ANT51x
from ifm electronic gmbh�
You can find information about the matching read/write heads on our website at:
www�ifm�com → data sheet search → ANT41 or ANT51
4 Function
You can find detailed information about the function of the system in the device
manual at:
www�ifm�com → data sheet search → DTE101 → Operating instructions
5 Installation
5.1 Installation distance
Due to the internal heating of the device a minimum distance to other objects of
10 mm is to be taken into account during installation�
A = 10 mm

7
UK
5.2 Installation orientation
The installation orientation can be freely selected�
In a wet environment upside-down mounting is not permitted�
5.3 Mounting options
5.3.1 Mounting on DIN rail
The device can be installed on a DIN rail of type NS35/15 or NS35/7�5�
1� Angle the device and place the fixing clamp onto the upper edge of the DIN rail�
2� Press device down�
3� Simultaneously rotate the device in the direction of the DIN rail�

8
5.3.2 Removal
1� Press device down�
2� Simultaneously rotate the device away from the DIN rail�
3� Remove the device from the top�
5.3.3 Mounting plate
The device can be fixed to a mounting plate using 2 screws (M4 x 35 or longer)�
M4 M4
This installation mode is recommended for vibration and shock require-
ments�

9
UK
6 Electrical connection
The device must be connected by a qualified electrician�
►Disconnect power before connecting the device�
►Observe the national and international regulations for the installation of
electrical equipment�
►Ensure voltage supply to EN 50178, SELV, PELV�
►Connect the device according to the indicated pin connection�
►A total current consumption of the device of 3 A must not be exceeded�
Please note the following points to ensure protection rating IP 67:
►Cover the unused sockets with protective caps�
►Tighten all protective caps and connectors with a tightening torque of 1 Nm�
You will find matching accessories at www�ifm�com
Accessories ifm article number
Protective cap E73004
Torque wrench E70390
6.1 AUX voltage supply
►Connect the device to the voltage supply using an M12 connection cable�
3
12
4
5
Pin Connection
1 24 V DC
2 Not used
3 0 V
4 Not used
5 Not used
You can find matching connection cables at:
www�ifm�com → data sheet search → DTE101 → Accessories

10
6.2 Field bus connection PROFINET IO Port 1 / Port 2
►Connect the device to a PROFINET IO controller using a suitable M12 Ethernet
connection cable�
12
34
Pin Connection
1 TD+
2 RD+
3 TD-
Note: screened connection
cable required
4 RD-
6.2.1 Factory setting of the Ethernet parameters
The following values are preset on delivery of the device:
Parameters Factory setting
IP address 192�168�0�79
Gateway address 192�168�0�100
Subnet mask 255�255�255�0
Auto-negotiation on
DHCP off
The settings can be changed via the unit’s webserver or via the PROFINET IO
controller�

11
UK
6.3 Process connections IO-1 ... IO-4
Each process connection can be used as input/output to IEC 61131 or for con-
nection of an RFID read/write head� The connections are set via the hardware
configuration of the PROFINET IO controller�
3
12
4
5
Pin Connection
1 L+
2 Switching input (I/Q)
3 L-
4 Switching output (C/Qo) or input (C/Qi)
5 Not used
The evaluation unit has to be disconnected before field units are connected�
Please note that the total current consumption of the device must not
exceed the value of 3 A�
You can find detailed information about the available operating modes in the
device manual at:
www�ifm�com → data sheet search → DTE101 → Operating instructions

12
6.4 Functional earth connection.
To ensure trouble-free operation the device must be connected to an earth
potential free from external voltage�
6.4.1 Mounting on DIN rail
The connection is made automatically via the DIN rail� Note that the DIN rail must
be connected with the earth potential�
6.4.2 Mounting plate
When the device is fixed on a mounting plate, connection is made via the left fix-
ing screw� Note that the plate must be connected with the earth potential�

13
UK
7 Operating and display elements
7.1 Reset to factory settings
The Ethernet parameters can be reset to the factory settings� Take the following
steps:
►Remove all cable connections from the device�
►Insert an electrically conductive bridge between pin 1 and pin 3 on the process
connection IO-3�
►Connect device with the voltage supply and wait until the yellow LED indication
on AUX and IO-3 flashes at approx� 8 Hz�
►Disconnect the device from the voltage supply and connect it again�
> The settings are reset�
7.2 LED indicators
The device indicates the current status of the interface via the status LEDs�
7.2.1 LED AUX
LED green LED yellow Status Note
Off Off No voltage supply UAUX < 5 V
On Flashes at
2 Hz Voltage supply too low 5 V ≤ UAUX ≤ 18 V
On Off Voltage supply OK 18 V ≤ UAUX ≤ 36 V

14
7.2.2 LED PROFINET Port 1 / Port 2
LED green LED yel-
low Status Note
Off Off No connection to another
Ethernet counterpart Link status "no link"“
On Off
Connection to Ethernet
counterpart exits, no data
exchange
Link status "link", "no traffic"
On
Flashes
sporadi-
cally
Connection to Ethernet coun-
terpart exists, data exchange
running
Link status "link", "traffic"
7.2.3 LED SF
LED red LED green Status Note
off off no voltage supply check voltage supply
off flashes "Node flash test", initiated by
PROFINET IO controller -
off on normal operation -
flashes off error on channel level
- overload
- temperature
- internal fault
on off error on device level - undervoltage
- temperature
flashes flashes self-test starting phase of the device

15
UK
7.2.4 LED BF
LED red LED green Status Note
off off no voltage supply check the voltage supply
off flashes PROFINET IO controller is in
STOP mode -
off on PROFINET IO controller is in
RUN mode -
flashes off
connection to the PROFINET
IO controller is established,
no valid configuration
check configuration
on off no connection to
PROFINET IO controller check connection
flashes flashes self-test starting phase of the device
7.2.5 LEDs IO1 ... IO4
The LED indications of the process connections differ with each connection
configuration�
Use as input to IEC 61131
LED green LED yellow Status Note
Off Off Interface deactivated Interface in PROFINET IO
controller not configured
On Off Interface activated, input on
L level (0 V) -
On On Interface activated, input on
H level (24 V) -
Flashes at
8 Hz
Flashes at
8 Hz Overload or short circuit -

16
Use as output to IEC 61131
LED green LED yellow Status Note
Off Off Interface deactivated Interface in PROFINET IO
controller not configured
On Off Interface activated, output
L-active (0 V) -
On On Interface activated, output
H-active (24 V) -
Flashes at
8 Hz
Flashes at
8 Hz Overload or short circuit -
Use with RFID read/write heads
LED green LED yellow Status Note
Off Off Interface deactivated Interface in PROFINET IO
controller not configured
Flashes at
2 Hz Off Interface activated, antenna
off -
On Off Interface activated, tag not
in the field -
On On Interface activated, tag in
the field -
Flashes at
8 Hz
Flashes at
8 Hz
Overload, short-circuit or
communication error -

17
UK
7.2.6 Special device- LED indications
LED Status Note
Green AUX LED on
Yellow AUX LED
flashes at 8 Hz
Yellow IO1���IO4 LEDs
flash at 8 Hz
Device is in the service mode
"emergency system started"�
A firmware update is neces-
sary and can be executed via
the web server�
Green AUX LED on
Yellow AUX LED
flashes at 8 Hz
Green IO1���IO4 LEDs
flash at 8 Hz
Yellow IO1���IO4 LEDs
flash at 8 Hz
Major error, device has to be
returned�
Hardware fault or permanent
data in the device are corrupt�
Green AUX LED on
Yellow AUX LED
Flashes at 8 Hz
Yellow IO3 LED
flashes at 8 Hz
Reset to factory settings -
8 Technical data
8.1 Data sheets
Data sheets can be found at:
www.ifm.com → data sheet search → DTE101
8.2 Device manual
The device manual can be found at:
www.ifm.com → data sheet search → DTE101 → operating instructions

18
9 Maintenance, repair and disposal
►Dispose of the device in accordance with the national environmental regula-
tions�
10 Approvals/standards
The EC declaration of conformity and approvals can be found at:
www.ifm.com → data sheet search → DTE101 → Approvals
11 Scale drawing
M12x1
M12x1
85
75 32,2
46,2
115
43,5
57,5
M4

19
UK
Table of contents