IFM Electronic ecomot200 DL0203 User manual

Operating instructions
Level control relay
DL0203
80097642 / 00 10 / 2014
UK

2
Contents
1 Preliminary note���������������������������������������������������������������������������������������������������4
1�1 Symbols and warnings used��������������������������������������������������������������������������4
2 Safety instructions �����������������������������������������������������������������������������������������������5
2�1 General����������������������������������������������������������������������������������������������������������5
2�2 Target group���������������������������������������������������������������������������������������������������5
2�3 Electrical connection��������������������������������������������������������������������������������������5
2�4 Handling ��������������������������������������������������������������������������������������������������������6
2�5 Installation location ����������������������������������������������������������������������������������������6
2�6 Housing temperature �������������������������������������������������������������������������������������6
2�7 Tampering with the device �����������������������������������������������������������������������������6
3 Functions and features ����������������������������������������������������������������������������������������7
3�1 Functionality ��������������������������������������������������������������������������������������������������8
3�1�1 Switching diagram ��������������������������������������������������������������������������������9
4 Operating and display elements ������������������������������������������������������������������������10
4�1 LEDs������������������������������������������������������������������������������������������������������������10
4�2 Potentiometer ����������������������������������������������������������������������������������������������10
5 Installation���������������������������������������������������������������������������������������������������������� 11
5�1 Installation of the device ������������������������������������������������������������������������������ 11
5�1�1 Remove the device����������������������������������������������������������������������������� 11
5�2 Mounting of the sensors ������������������������������������������������������������������������������ 11
6 Electrical connection������������������������������������������������������������������������������������������12
6�1 Connection accessories ������������������������������������������������������������������������������12
6�2 Terminal connection�������������������������������������������������������������������������������������12
6�3 Voltage supply (power) ��������������������������������������������������������������������������������13
6�3�1 AC supply �������������������������������������������������������������������������������������������13
6�3�2 DC supply �������������������������������������������������������������������������������������������13
6�4 Inputs�����������������������������������������������������������������������������������������������������������14
6�4�1 General�����������������������������������������������������������������������������������������������14
6�4�2 Connection of sensor 1 (upper level)��������������������������������������������������14
6�4�3 Connection of sensor 2 (lower level) ��������������������������������������������������14
6�5 Outputs ��������������������������������������������������������������������������������������������������������15
6�5�1 Relay output ���������������������������������������������������������������������������������������15
6�5�2 Transistor output���������������������������������������������������������������������������������15

3
UK
6�6 Connection of the valve or pump�����������������������������������������������������������������15
7 Settings��������������������������������������������������������������������������������������������������������������16
7�1 Input delay ���������������������������������������������������������������������������������������������������16
8 Scale drawing ����������������������������������������������������������������������������������������������������17
9 Technical data����������������������������������������������������������������������������������������������������17
9�1 Approvals/standards ������������������������������������������������������������������������������������18
10 Troubleshooting �����������������������������������������������������������������������������������������������19
11 Maintenance, repair, disposal ��������������������������������������������������������������������������19
11�1 Maintenance ����������������������������������������������������������������������������������������������19
11�2 Cleaning the housing surface ��������������������������������������������������������������������19
11�3 Repair ��������������������������������������������������������������������������������������������������������19
11�4 Disposal �����������������������������������������������������������������������������������������������������19
This document is the original instructions�

4
1 Preliminary note
This document applies to the level control relay DL0203�
This document is intended for specialists� These specialists are people who are
qualified by their training and their experience to see risks and to avoid possible
hazards that may be caused during operation, installation or maintenance of the
device�
Read this document before use to familiarise yourself with operating conditions,
installation and operation� Keep this document during the entire duration of use of
the device�
WARNING
Adhere to the warning notes and safety instructions (→ 2 Safety instructions).
1.1 Symbols and warnings used
►Instructions
> Reaction, result
[…] Designation of keys, buttons or indications
→Cross-reference
Important note
Non-compliance can result in malfunction or interference�
Information
Supplementary note�
WARNING
Warning of serious personal injury�
Death or serious irreversible injuries may result�
CAUTION
Warning of personal injury�
Slight reversible injuries may result�
NOTE
Warning of damage to property�

5
UK
2 Safety instructions
2.1 General
Follow the operating instructions� Non-observance of the instructions, operation
which is not in accordance with use as prescribed below, wrong installation or
incorrect handling can affect the safety of operators and machinery�
The installation and connection must comply with the applicable national and
international standards� Responsibility lies with the person installing the device�
The system installer is responsible for the safety of the system into which the
device is integrated�
2.2 Target group
The device must only be installed, connected and put into operation by a qualified
electrician�
2.3 Electrical connection
Disconnect the unit externally before handling it� Also disconnect any
independently supplied relay load circuits�
Make sure that the external voltage is generated and supplied according to the
requirements for safety extra-low voltage (SELV) since this voltage is supplied
without further measures near the operating elements and at the terminals for the
supply of connected sensors�
The wiring of all signals in connection with the SELV circuit of the device must also
comply with the SELV criteria (safety extra-low voltage, safe electrical isolation
from other electric circuits)�
If the externally supplied or internally generated SELV voltage is externally
grounded, the responsibility lies with the user in accordance with the applicable
national installation regulations� All statements in these operating instructions refer
to the unit the SELV voltage of which is not grounded�
It is not allowed to supply external voltage to the terminals for the pulse pick-up
supply� The consumption of current which exceeds the value given in the technical
data is not allowed�
An external main switch must be installed for the unit which can switch off the unit
and all related circuits� This main switch must be clearly assigned to the unit�

6
2.4 Handling
Be careful when handling the unit once power is applied� This is only allowed by
qualified personnel due to the protection rating IP 20�
2.5 Installation location
For the correct operation the device must be mounted in a housing which can only
be opened using a tool or in a locked control cabinet (both protection rating IP 54
or higher) as an enclosure in accordance with EN 61010�
2.6 Housing temperature
As described in the technical specifications below the device can be operated in
a wide ambient temperature range� Because of the additional internal heating the
operating elements and the housing walls can have high perceptible temperatures
when touched in hot environments�
2.7 Tampering with the device
In case of malfunction of the unit or queries please contact the manufacturer�
Any tampering with the device can seriously affect the safety of operators and
machinery� This is not permitted and leads to the exclusion of any liability and
warranty claims�

7
UK
3 Functions and features
The device is used to keep a medium level between 2 sensors� To do so it controls
the inlet of a tank (e�g� valve or pump)�
It receives signals from 2 external sensors and switches its outputs according to
the adjustable input delay� The input delay protects against unintended switching
caused by waves on a medium surface�
Sensor supply and transistor output are equipped with an independent overload/
short circuit protection�
WARNING
The device is not approved for safety-related tasks in the field of operator
protection�

8
3.1 Functionality
2
In 1 In 2
7
6
1
5
3
4
Level control
1: Sensor 1 with normally closed output for input 1 (upper level)
2: Sensor 2 with normally open output for input 2 (lower level)
3: Tank with liquid or dry bulk material
4: Valve or pump (inlet)
5: Relay output
6: Transistor output
7: PLC or signalling device
Process Relay
After switching on the device de-energised
Level is below both sensors energised
Level is above both sensors de-energised
Level is between the sensors depending on the previous state
Relay energised, i�e� switched (transistor output switched)

9
UK
3.1.1 Switching diagram
X X
t [s]
X
SP1
1
SP2
X X
5
4
2
3
Sensor 1
Level
Sensor 2
Power
Output
= relay energised, i�e� switched (transistor output switched)
1: Level of the medium
2: Sensor 1 with normally closed output for input 1 (upper level)
3: Sensor 2 with normally open output for input 2 (lower level)
4: Power supply
5: Output
SP1
SP2
X
Switch point sensor 1 (upper level)
Switch point sensor 2 (lower level)
Input delay (→ 7.1)

10
4 Operating and display elements
Output
Input 1
Input 2
Power
(sec)
Input Delay
5
100
2
3
1
Operating and display elements
1: LEDs
2: Potentiometer
3: Panel for labelling
4.1 LEDs
LED Colour Status Description
Power Green On Voltage supply OK
Input 1 Yellow On Input 1 signal "High"
Output Green On Relay energised (transistor switched)
Input 2 Yellow On Input 2 signal "High"
Error signals and diagnosis (→ 10 Troubleshooting)
4.2 Potentiometer
Potentiometer Setting
Input Delay Input delay [s] (→ 7.1)

11
UK
5 Installation
5.1 Installation of the device
►Install the device on a 35 mm DIN rail�
►Leave enough space between the unit and the top and bottom of the control
cabinet to enable air circulation and to avoid excessive heating�
►Take into account the internal heating of all units when mounting several units
side by side� The environmental conditions must be observed for every unit�
5.1.1 Remove the device
5.2 Mounting of the sensors
►Follow the manufacturer’s installation instructions�

12
6 Electrical connection
6.1 Connection accessories
The unit is supplied including connectors�
You can find more information about the available accessories at:
www.ifm.com → Data sheet search → Article number → Accessories
6.2 Terminal connection
6
5
7
21 22 23 24
18
17
19
8
1 2 3 4
14
15
13
Input 2
Input 1
(pnp)
Sensor
supply
(pnp)
or DCAC Power
Out
In
NLL N
05 06 07 08
01 02 03 04
21 22 23 24
17 18 19 20
13 14 15 16
Terminal connection
WARNING
Only the supplied or technically identical connectors may be used on the
terminals blocks for the AC supply (21...24) and the relay output (17...20) (→ 9
Technical data)�
To ensure protection rating IP 20 for the housing and the terminals, fully tighten
the screws of the unused connector contacts�
WARNING
Do not use unconnected terminals which are not shown in the drawing such as
terminal 20 as support point terminal�

13
UK
6.3 Voltage supply (power)
►Voltage supply see type label�
►Connect the device only to one of the possible voltage connections, i�e� either
to terminals 21/22 and 23/24 (AC) or to terminals 1/2 and 3/4 (24 V DC)�
►Lay all supply and signal cables separately� Use a screened cable if required in
the application�
6.3.1 AC supply
WARNING
The AC supply cable must be protected according to the cross-section used
(max� 10 A)�
If the unit is supplied on AC, the low voltage provided for the sensor supply meets
the SELV criteria according to EN 61010, overvoltage category II, soiling degree 2�
6.3.2 DC supply
►The SELV criteria (safety extra-low voltage) must be met for the DC supply�
►The DC supply cable L+ (terminals 1/2) must be protected externally with a
315 mA time-lag fuse (5 x 20 mm or similar)�
The DC supply terminals are directly connected to the sensor supply terminals�

14
6.4 Inputs
6.4.1 General
The assignment of the sensors to the inputs is predetermined�
Input 1 = sensor 1 with normally closed output (upper level)
Input 2 = sensor 2 with normally open output (lower level)
The connection of mechanical switch contacts is not recommended since
they tend to bounce and produce faulty pulses�
Terminals 5 and 7 can be used for the sensor supplies�
6.4.2 Connection of sensor 1 (upper level)
For the correct operation use a sensor with normally closed output
(→ 3.1 Functionality).
3-wire DC PNP 2-wire DC
quadronorm
2-wire AC/DC Mechanical
switch
5
6
7
BN
BK
BU
5
6
BK
WH
5
6
BN
BU
5
6
5
6
7
BN
BK
BU
5
6
BK
WH
5
6
BN
BU
5
6
5
6
7
BN
BK
BU
5
6
BK
WH
5
6
BN
BU
5
6
5
6
7
BN
BK
BU
5
6
BK
WH
5
6
BN
BU
5
6
BN = brown BK = black BU = blue WH = white
6.4.3 Connection of sensor 2 (lower level)
For the correct operation use a sensor with normally open output
(→ 3.1 Functionality).
3-wire DC PNP 2-wire DC
quadronorm
2-wire AC/DC Mechanical
switch
5
8
7
BN
BK
BU
5
8
WH
BK
5
8
BN
BU
5
8
5
8
7
BN
BK
BU
5
8
WH
BK
5
8
BN
BU
5
8
5
8
7
BN
BK
BU
5
8
WH
BK
5
8
BN
BU
5
8
5
8
7
BN
BK
BU
5
8
WH
BK
5
8
BN
BU
5
8
BN = brown BK = black BU = blue WH = white

15
UK
6.5 Outputs
6.5.1 Relay output
► Connect the changeover contact depending on the used valve or pump (→ 6.6
Connection of the valve or pump)�
►To prevent excessive wear and to comply with the EMC standards, interference
suppression of the contacts is required for switching inductive loads�
WARNING
If the device is operated on an AC supply (terminals 21/22 and 23/24) this
must use the same supply cable (phase) as the voltage supply to switch an AC
voltage via the relay output�
If the relay output is used to switch very small currents (e�g� PLC input),
considerable contact resistance can arise� For this purpose use the
transistor output�
6.5.2 Transistor output
►The transistor output needs an external +24 V DC supply on terminal 13�
Protect this +24 V DC supply cable externally with a 315 mA time-lag fuse (5 x
20 mm or similar)�
►Connect the reference point (GND) of the external power supply with terminal
15 or 3/4 of the device� Otherwise no switching operation is possible�
►The SELV criteria (safety extra-low voltage) must be met for the DC supply of
the transistor outputs�
6.6 Connection of the valve or pump
►The principle of normally open operation must be adhered to for the connection
of the valve or the pump� For example, connect the normally open output of the
device (terminals 17/18) to a valve with normally closed operation�
By adhering to the principle of normally open operation the inlet or outlet of
the medium is blocked in the event of a wire break or a power failure�

16
7 Settings
►Set the continuously adjustable potentiometer using a suitable screwdriver�
7.1 Input delay
The input delay sets the minimum duration of the stable input signal to be evaluated�
It protects against unintended switching caused by waves on a medium surface�
Value 0…10 s

17
UK
8 Scale drawing
25,4 109,1
93
35,5
116
9 Technical data
Level control relay DL0203
Nominal voltage AC [V] 110����240
Nominal frequency [Hz] 50����60
Voltage tolerance [%] -20/+10
Power consumption [W] 6
Alternatively
Nominal voltage DC [V] 27 (typ� 24)
Voltage tolerance [%] -20/+10
Power consumption [W] 4
Auxiliary energy for sensors [V] 18.5...30 DC SELV, ≤ 100 mA
Sensor type PNP (type 2 to IEC 61131-2)
Input frequency [Hz] ≤ 5

18
Level control relay DL0203
Relay contact rating [A] 4
Resistive load (240 V AC or 24 V DC)
Electrically isolated
Reinforced insulation to EN 61010
Overvoltage category II,
Degree of soiling 2 to 240 V AC nominal voltage
Transistor switching voltage [V] 10…30 DC SELV
Transistor current rating [mA] ≤ 100
Protection housing / terminals IP 20 / IP 20
Ambient temperature [°C] -25…60
Storage temperature [°C] -25…70
Max� perm� relative humidity [%] 80 (31 °C)
Linearly decreasing to 50 (40 °C)
Non condensing
Maximum operating altitude [m] 2000 above sea level
Connection
Device 4-pole terminal blocks with 5�0 mm pitch
Connector 4 poles with screw connection
(supplied with the unit)
Type Phoenix Contact MSTBT 2,5/4-ST BK
0�2…2�5 mm² (AWG 30…12)
Data sheets are available at:
www.ifm.com → Data sheet search→ Article number
9.1 Approvals/standards
EC declarations of conformity, approvals etc� can be downloaded at:
www.ifm.com → Data sheet search → Article number → More information

19
UK
10 Troubleshooting
LED Error Troubleshooting
Power
Input 1
Output
Input 2
-- --
Sensor wire break or wrong
sensor type
Check sensors and their
connections
Short circuit at sensor supply Remove short circuit
-- -- Short circuit at transistor output Remove short circuit
-- Internal device error Contact service
Legend:
off on flashing -- any
11 Maintenance, repair, disposal
11.1 Maintenance
The unit is maintenance-free�
11.2 Cleaning the housing surface
►Disconnect the device�
►Clean the device from dirt using a soft, chemically untreated and dry cloth�
Micro-fibre cloths without chemical additives are recommended�
11.3 Repair
►The device must only be repaired by the manufacturer�
Observe the safety instructions�
11.4 Disposal
►Dispose of the device in accordance with the national environmental
regulations�
Table of contents
Other IFM Electronic Relay manuals
Popular Relay manuals by other brands

LynTec
LynTec NPAC Instruction bulletin

GE
GE Masoneilan 469 Series Communications guide

GE
GE 750 instruction manual

Greystone Energy Systems
Greystone Energy Systems GT-AR4 Series installation instructions

LOVATO ELECTRIC
LOVATO ELECTRIC EXP10 02 manual

Schrack Technik
Schrack Technik DOWNUNDER OUT TCD instruction manual