Airtime™Sport Instructions
Introduction
Welcome to truly wireless audio with 25 hours total
of battery life and quick charging case.
Pairing the Wireless Earbuds with
Your Device
1. Simply open the case and remove the earbuds.
A pairing signal will be sent to your Bluetooth®
device. The earbuds will flash white, indicating
pairing mode.
2. On your device, go to Bluetooth® under
Settings and select IFROGZ Airtime Sport.
3. Complete any additional steps your device
may require. The lights on the earbuds will flash
white and then turn o, indicating that pairing
was successful.
Turning Earbuds On/Off
To turn the earbuds on, simply remove the buds
from the case.
If you would like to use only one bud, simply remove
the right earbud from the case. The right earbud
is the primary bud and can be used without the
other. Please note, the left earbud will not work
alone unless the right earbud is also removed from
the case.
To turn the earbuds o, simply return them to the
case. You can also tap then hold the IFROGZ icon on
the earbud for 10 seconds to turn it o; it will flash
red, indicating the power is o.
The earbuds will go into hibernation mode if not
used for 20 minutes.
Using the Earbuds
AIRTIME SPORT True Wireless earbuds have built-in
touch navigational controls. Just tap on the end of
the earbud (on the IFROGZ logo) to navigate.
Music Controls
Left Bud Actions Right Bud
Play / Pause Quick Tap Play / Pause
Previous Track 2x Taps Nex t Track
Decrease Volume Tap & Hold Increase Volume
Call Controls
Answer Call /
End Call Quick Tap Answer Call /
End Call
Cancel Call Tap & Hold Cancel Call
Siri / Voice
Command 3x Taps Siri / Voice
Command
Charging the Wireless Earbuds
The case carries enough power to charge the
earbuds up to 4 times.
1. Place the earbuds in the charging case. You’ll
feel them magnetically click into place.
2. A red light on the earbuds will indicate
charging. When the red light turns o, they are
fully charged.
Charging the Case
Your case comes charged and ready to go. You can
re-charge the case wirelessly using a wireless
charging pad, or charge the case manually using
the included USB-C cable.
Wireless Charging
1. Simply drop the charging case on a compatible
wireless charging pad.
2. The Battery Indicator light will flash according
to its current battery level. This indicates
your case is charging. When all 4 lights are
illuminated, your case is fully charged.
Manual Charging
1. Connect the included USB-C charging cable to
the port on the side of your case.
2. Connect the USB-A end of the cable to your
preferred 5V USB outlet.
3. The Battery Indicator light will flash according to
its current battery level. This indicates your case
is charging. When all lights are fully illuminated,
your case is fully charged. They will stay fully
illuminated until the case is disconnected from
the power source.
4. Disconnect the charging cable.
Quick Charge Feature
Get one more hour of playtime by nesting the
earbuds in the charging case for ten minutes.
Checking the Battery Level
Your case carries enough power to charge your
wireless earbuds 4 times for a total of 25 hours.
To check how much power your case still has, place
the earbuds in the case. The LED on the front of the
case will illuminate, indicating how much battery
remains in the case:
· If it lights up completely, 75% or
more remains
· If it lights up ¾ of the way, between
50-74% remains
· If it lights up ½ of the way, between
25-49% remains
· If it lights up ¼ of the way, less than
24% remains.
Factory Reset
If you have functionality issues, a factory reset
can help. Here’s how to perform one.
1. Place both buds in the case.
2. Reset the right bud.
a. Remove the right bud from
the case.
b. Tap and hold for 10 seconds
until light flashes red and
turns o.
c. Tap and hold for five seconds
until light turns on and flashes
red and white.
d. Quickly tap the bud six times,
the light will turn o.
e. Return the bud to the case.
3. Reset the left bud.
a. Remove left bud from the case.
b. Quickly tap the bud six times,
the light will turn o.
c. Return the bud to the case.
4. Connect left and right.
a. Remove both buds from the
case and allow them to connect
to each other for about five
seconds.
5. Connect as normal.
a. The buds are now reset to
factory settings. Remove
them from the case and pair
as normal.
