Igloo IWCBL5OSCLD1CHBKS Quick guide

All products are trademarks of Nostalgia Products LLC.
Worldwide design & utility patented or patents pending.
© 2020 Nostalgia Products LLC.
www.nostalgiaproducts.com
(rev. 05/14/20 SN)
All products are trademarks of Nostalgia Products LLC.
Worldwide design & utility patented or patents pending.
© 2020 Nostalgia Products LLC.
IGLOO® and the Igloo design are trademarks of Igloo Products Corp. All rights reserved.
www.nostalgiaproducts.com
(rev. 05/14/20 ET)

IWCBL5OSCLD1CHBKS
Hot & Cold Bottom Load Self-Cleaning Water Dispenser
Dispensador auto-limpiante de agua caliente y fría con carga inferior
Distributeur d'eau chaude et froide autonettoyant à chargement par le bas
Instructions and Recipes
Instrucciones y recetas
Instructions et recettes

ENGLISH
2
Make everyday a party!
Visit www.nostalgiaproducts.com for more fun products.
CONTENTS
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
ADDITIONAL IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . 4
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
PARTS & ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
HOW TO OPERATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
HELPFUL TIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CLEANING & MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . .10
RETURNS & WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SAFETY
Appliance Specications:
120 Volts, 60 Hz, 425 Watts
THIS PRODUCT IS FOR USE IN 120V AC OUTLET ONLY.
Refer to www.nostalgiaproducts.com/user-manuals/ for the most updated manual.
Your safety and the safety of others is very important.
We have provided many important safety messages in this manual and
on your appliance. Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can
cause serious injury to you and others.
All safety messages will follow the safety alert symbol.
All safety messages will tell you what the potential hazard is, tell you how to reduce the
chance of injury, and tell you what can happen if the instructions are not followed.

ENGLISH
3
IMPORTANT SAFEGUARDS
A person who has not read and understood all operating and safety instructions
is not qualied to operate this appliance. All users of this appliance must read and
understand this Instruction Manual before operating or cleaning this appliance.
When using electrical appliances, basic safety precautions
should always be followed, including:
1. Read all instructions before operating this appliance.
2. DO NOT TOUCH the hot surfaces. Use handles or knobs.
3. This appliance is NOT A TOY.
4. This appliance is not intended for use by persons (including children) with reduced physical,
sensory, or mental capabilities, or lack of experience and knowledge, unless they are closely
supervised and instructed concerning use of the appliance by a person responsible for
their safety. Close supervision is necessary when any appliance is used by or near children.
Children should be supervised to ensure that they do not play with the appliance.
5. Close supervision is necessary when any appliance is used by or near children.
6. Turn the appliance OFF, then unplug from the outlet when not in use, before
assembling or disassembling parts and before cleaning. To unplug, grasp
the plug and pull from the outlet. Never pull from the power cord.
7. Do not operate any appliance with a damaged cord or plug or after the appliance
malfunctions, or is dropped or damaged in any manner. Contact the manufacturer
at their customer service telephone number for information on examination,
repair, or adjustment. Customer service number is [phone].
8. Unplug from outlet when not in use, before removing parts and before cleaning.
Allow to cool before putting on or taking o any parts, and before cleaning.
9. DO NOT operate any appliance with a damaged cord or plug, or after the appliance
malfunctions, or if the appliance has been damaged in any manner. Return the
appliance to the nearest repair shop for examination, repair or adjustment.
10. The manufacturer does not recommend the use of accessory attachments other than
what is provided by the manufacturer. Use of attachments may cause injuries.
11. DO NOT use the appliance for other than its intended use.
12. DO NOT use outdoors. FOR HOUSEHOLD USE ONLY.
13. DO NOT place on or near a hot gas or electric burner, or in a heated oven.
14. DO NOT let cord hang over edge of table or counter, or touch hot surfaces.
15. NEVER leave unit unattended while in use or when plugged into an outlet.
16. Extreme caution must be used when moving an appliance containing hot food.
17. Always attach plug to appliance rst, then plug cord in the wall outlet. To
disconnect, turn any control to "o," then remove plug from wall outlet.

ENGLISH
4
ADDITIONAL IMPORTANT SAFEGUARDS
Operating Safety Precautions
1. Prior to use, this dispenser must be properly assembled
and installed in accordance with this manual.
2. This dispenser is intended only for water dispensing. Do NOT use other liquids.
Do NOT use for other purposes. Never use other liquids in the dispenser
other than known and microbiologically safe bottled water. Warranty is void
if used with any other liquids, such as coee, tea, juices, beer or wine.
1. Instructions for the Electrical Cord and Plug
1. ELECTRICAL SHOCK HAZARD: Failure to follow these instructions can result in death, re, or
electrical shock.
• Plug into a grounded 3 prong outlet.
• DO NOT remove ground prong.
• DO NOT use an adapter.
• DO NOT use an extension cord.
2. This unit MUST be grounded. In the event of an electrical short circuit, grounding reduces
the risk of electric shock by providing an escape wire for the electric current. This unit is
equipped with a cord having a grounding wire with a grounding plug. The plug must be
plugged into an outlet that is properly installed and grounded.
3. WARNING: Improper use of the grounding plug can result in a risk of electric shock. If the
plug does not t fully into the outlet, contact a qualied electrician. Do not attempt to
modify the plug in any way.
4. A short power supply cord is provided to reduce the risk resulting from becoming entangled
or tripping over a long cord.
The manufacturer does not recommend using this machine in countries that do
not support 120V AC even if a voltage adapter, transformer, or converter is in use.
SAVE THESE INSTRUCTIONS!

ENGLISH
5
INTRODUCTION
Thank you for purchasing the HOT & COLD WATER BOTTOM LOAD SELF-CLEANING WATER
COOLER from IGLOO! With the Igloo Hot & Cold Bottom Load Water Cooler, ease is at
your ngertips! This bottom-loader gives you ice-cold and hot water in just seconds!
This water cooler allows you to load 3 or 5 gallon bottles with no plumbing required!
There is a child safety lock for the hot button so there are no accidents. Satisfy your
thirst with cool water or relax with a hot beverage using the brand you can trust!
• Bottom loading cooler for hot & cold water
• No water LED indicator light with night light
• Ozone self-cleaning technology helps prevent formation of bacteria
• Uses standard 3 and 5 gallon bottles (not included)
• Direct water line hookup available
• Adjustable rear leveling legs
• Hot & cold push buttons & two separate spigots with child safety lock for hot button
• Over heating protection for hot tank
• Removable stainless steel drip tray for easy clean up
• Dispensing area suitable for up to 8”bottle
• Hot water tank capacity: 1.2L/ Cold water tank capacity: 4L
• Water temperature: Hot 200°F/ Cold 40°F
• Hot and Cold LED On/O switches
• Compressor cooling
• Retractable siphon works with 3 & 5 gallons

ENGLISH
6
PARTS & ASSEMBLY
PARTS
1, 2
3
4
7
5
1/2- Hot & Cold Water Spigot
3- Room Removable Drip Tray
4- Siphon pumps/Cover (Retractable)
5- Hot Water Push Button/Safety Lock
6- Cold Water Push Button
7- Hot Water On/O Switch
8- Cold Water On/O Switch
9- LED Light Switch
8
6
9

ENGLISH
7
ASSEMBLY
Use EXTREME CAUTION when handling the appliance. When taking out of
package, it is recommended to lay the box safely on its side. For the most part,
the HOT & COLD WATER BOTTOM LOAD WATER COOLER is assembled. Once
unpacked and standing up right, the drip tray will need to be inserted.
Location Requirements:
1. Install in the area where it is protected from the elements including direct sun.
2. Install and use only on a hard, at and level surface.
3. Do NOT place the dispenser inside an enclosed space or cabinet.
4. Position the dispenser no closer than 4 inches from the wall with at
least 4 inches clearance on the sides to permit free airow.
5. Service should only be performed by a certied technician.
WATER COOLERS
It is very easy to replace 3 or 5 gallon coolers (not included). NOTE:
Excessive weight hazard - It is recommended to use two or more people
to move and install bottles. Failure to do so can result in injury.
1. Open up the cabinet door on the bottom and take the water cap o the water cooler.
2. Place the siphon pump inside of the water jug so it's touching the bottom.
3. Make sure the siphon pump cover cap ts securely over
the water jug top, ensuring no leakage.
NOTE: The siphone pump is adjustable. Adjust the length by pulling the
portion of the tube to its maximum extension. Insert the probe into the bottle
and push it down. The probe will self-adjust to its appropriate length.
4. Close the door.
HOW TO OPERATE
WARNING: This unit is intended for water dispensing only. Do NOT use
other liquids. Do NOT use for other purposes. Warranty is void if used
with any other liquids such as coee, tea, juices, beer or wine.
This dispenser has been designed to use water bottles with a 3
or 5 gallon capacity. Do NOT use alternative bottles.
Initial Set Up
NOTE: Make sure that switches are ON. Both the Hot and Cold water, and
LED light switches are located in the back of the water cooler.
1. Remove the tamper seal from bottle cap and remove the cap.
2. Place the siphon pump inside the water cooler and make sure
cap is on securely and place inside water cooler door.
3. Plug the cord into a properly grounded wall outlet. WARNING:
Always make sure that the cord is away from a water source.
Dispensing Cold Water
After setup, it will take up to one hour to get the water to its maximum cold temperature.

ENGLISH
8
1. Place bottle, glass, or pitcher below the water tap.
2. Push the cold water button downward
to start dispensing water.
3. Release the button once the desired ll
level is achieved.
Dispensing Hot Water
After setup, it will not take long to reach maximum
hottest temperature. NOTE: For safety, there
is a lock on the dispensing button.
1. Place bottle, glass, pitcher, pot below the hot water tap.
2. Release child-safety lock by pushing inward
on the red button while pushing the hot
water button downward at the same time to start dispensing water.
3. Release the button once desired ll level is achieved.
WARNING: Be careful when dispensing hot water as temperature can reach 200 °F.
Self-Cleaning Mode
The unit's self-cleaning feature prevents the formation of Biolm. The
self-cleaning feature is not intended for water purication.
When the LED light is ashing it indicates that the self cleaning takes place. When
the LED light is constantly lit it indicates that the self clean protection is on.
NOTE: Self cleaning works every four hours for a short time.
The selfcleaning pump sound is normal.
Replacing An Empty Bottle/Low Water Indicator lights
When your water bottle is empty, the EMPTY BOTTLE lights will blink until a fresh bottle is
installed. You may also hear a sucking sound when the bottle is empty and needs changing. This
is normal and is another way to be alerted that your bottle is empty and needs to be replaced.
To install a new bottle:
1. Open the door and slide the bottle out.
2. Place the fresh bottle in front of the tray.
3. Clean the fresh bottle using a soft cloth and warm soapy water.
4. Remove the entire plastic cap from the top of the bottle.
5. Remove probe from old bottle and insert into the fresh bottle.
6. Push the probe down until it is seated.
7. Slide the bottle onto the tray and close the door completely.
HELPFUL TIPS
Do the LED lights use a lot of electricity?
No. LED lights are known for being energy ecient and consume very little energy.
I can’t nd the rectangular bottles? What other kind of bottles does the cooler take?
The cooler will accept any standard three or a ve gallon water bottle, circular or rectangular.

ENGLISH
9
How do I know when and if the Self Cleaning function is working?
The self cleaning function will run every four hours and the self clean LED light will ash.
Between self clean cycles, the LED light is glowing steady to
indicate that cooler is protected from contamination.
Can I use anything else other than bleach for cleaning the water cooler?
Bleach is safe to use to clean the machine. However, if you wish you can use a
vinegar based solution instead. Mix 16 oz of vinegar per every gallon of water.
There is no hot or cold water?
Ensure that both the hot and cold buttons on the back side of the cooler have been turned
on. The LED lights on the control panel will have a steady glow indicating the power has
been turned on. When lights are ashing, heating and cooling is currently taking place.
The water is not pumping water into the holding tank.
Ensure that the front door of the cooler is closed. In the event the cooler door is not closed
the pump will not be activated. If pump is still not being activated reset the power.
Where is the lter for the air intake?
The lter is located on the top of the probe. The lter resembles a black sponge.
Does the air lter need to be washed or changed?
No, the lter does not need to be washed or changed. If you desire, the lter can be cleaned
by unscrewing the cover on top of bottle cap the lter can then be removed for washing.
Hot water tap is dripping.
Perform de-scaling procedure outlined in cleaning section.
The buttons for dispensing water are slow-moving or jammed.
Ensure that buttons are clean and no dust or particles are causing buttons to move slowly.
Dispenser is not operating.
Make sure that the power cord is properly connected to a working outlet.
Water is leaking.
Replace water bottle. The most common cause of this issue is a cracked bottle.
If the leak remains, unplug unit and call customer service for assistance.
No water is coming from the taps.
Make sure the water bottle is not empty. If it is, replace it.
If not, adjust the probe to an appropriate length.
Water dispensed is not cold.
Please note that it takes a minimum of one hour after setup to dispense cold water. Make
sure that the back of the dispenser is at least 4 inches from a wall and that air is free to
ow on all 4 sides of the dispenser. Make sure that the cold-water switch is ON.
Water dispensed is not hot.
Please note that it takes approximately fteen to twenty
minutes after setup to dispense hot water.
Make sure that the power cord is properly connected to a working
outlet. Make sure that the hot-water switch is ON.

ENGLISH
10
Water tastes bad.
Drain the water from the reservoirs and replace the bottle with a fresh one.
Clean cooler as outlined in the PROPER CARE & DESCALING section.
CLEANING & MAINTENANCE
General Cleaning
General cleaning should be performed as needed and only takes ve minutes or less.
1. Clean the cabinet surfaces using a soft cloth and warm, soapy water. Rinse.
2. Wipe dust in the back of the water cooler to improve eciency.
3. Remove drip tray cover and hand wash. Take a cloth and warm,
soapy water to rinse the inside of the drip tray. Rinse.
4. Reattach drip tray.
Cleaning Water Lines & Reservoirs
Cleaning the water lines is recommended to happen once every three months.
NOTE: Recommended to do before loading a new 3 or 5 gallon jug.
1. Unplug power cord from outlet.
2. Remove water cooler bottle.
3. Remove the siphon pump and clean with warm, soapy water. Rinse.
4. Fill water cooler jug with a mixture of water and bleach and let it sit for 30 minutes.
5. Install the water bottle lled with cleaning solution and allow the reservoir to ll with
the solution. Let the mixture sit for ve to 10 minutes to disinfect the reservoir.
6. Drain the cleaning mixture by dispensing it from both taps into a bowl or pitcher.
7. Rell your empty water bottle with clean water and allow to ll the reservoir
again. Drain again through the spigots. If you detect a vinegar taste or
chlorine taste, add another two gallons of clean water, drain and retest.
8. Install a new bottle of water and plug in the power cord into grounded outlet.
Descaling
If you use spring (mineral) water you will need to de-scale your hot
water tank. Heated spring (mineral) water will cause minerals to fall
out. Eventually they will plug up your waterways, resulting in a gradual
slowdown of the ow rate, leaking faucets, and other problems.
Descaling Solutions
Cooking vinegar is proven to remove calcium deposits eciently.
Depending on the frequency of decalcication treatments, please
use the following proportions of White Vinegar.
• For descaling once every three months, use two cups (500
ml) of white vinegar with 2.5 liters of hot water.

ENGLISH
11
• For descaling once every six months, use a mixture of six cups
(1500 ml) of white vinegar with two liters of hot water.
• For descaling once every year, use 12 cups (3000 ml) of
white vinegar and one liter of hot water.
• For descaling less frequently than once a year, use undiluted white vinegar.
Descaling Procedure
1. Turn o hot & cold switches and unplug the cooler from the wall.
2. Using rear drain plug, drain the water from the cooler into a bucket and discard the water.
• Locate the white plastic cap at the back of the cooler.
• Remove the screw and remove the clear silicone drain plug and allow water to drain out.
• Re-attach the drain plug and plastic cap before proceeding.
3. Fill a bucket or empty 5-gallon water bottle with solution of white
vinegar. For proportions, refer to "Descaling Solutions" section. Choose
quantity in accordance with the frequency of your treatments.
4. Attach or insert the probe to the bucket/bottle.
5. Place the bucket/bottle into the cooler and close the door. The
water will be pumped up into the holding tanks.
6. Wait for 1 hour. Using rear drain plug, drain the water from
the cooler into a bucket and discard the water.
• Locate the white plastic cap at the back of the cooler.
• Remove the screw.
• Remove the clear silicone drain plug and allow water to drain out.
• Re-attach the drain plug and plastic cap before proceeding.
7. Fill the bucket/bottle with tap water and place into the machine.
8. Plug the cooler back into the wall, do not turn hot or cold
switches ON, close the door and wait for 10 minutes.
9. Dispense water from both cold and hot faucets until
smell from cleaning substances disappears.
10. Open drain plug and cap once again and drain all tap
water. Replace the drain plug and cap.
11. Place a fresh bottle of water into the machine and operate as usual.
12. This procedure must be repeated every 3 to 6 months, depending
on mineral content and usage of water cooler.

ENGLISH
12
RETURNS & WARRANTY
SHOULD YOUR UNIT NOT WORK OR IF DAMAGED WHEN YOU FIRST TAKE IT OUT OF
THE BOX, PLEASE RETURN IT TO THE PLACE OF PURCHASE IMMEDIATELY.
Dispensador auto-limpiante de agua caliente y fría con carga inferior / IWCBL5OSCLD1CHBKS
Should you have any questions, please contact us via email or at the customer service number listed
below between the hours of 8:00 AM and 5:00 PM, Monday through Friday, Central Standard Time.
Distributed by:
Nostalgia Products LLC
1471 Partnership Dr.
Green Bay, WI 54304-5685
Customer Service
Phone: [phone]
Web: www.nostalgiaproducts.com
Customer Service Inquiry
To submit a Customer Service inquiry, go to www.nostalgiaproducts.com and ll
out the Customer Service Inquiry form and click the Submit button.
A representative will contact you as soon as possible.
Product Warranty Terms
Nostalgia Products LLC (the“Company”) hereby warrants that for a period of one (1) year from the
date of original purchase, this product will be free of defects in material and workmanship under
normal home use, provided that the product is operated and maintained in accordance with the
operating instructions. As the sole and exclusive remedy under this warranty, the Company will
at its discretion either repair or replace the product found to be defective, or issue a refund on the
product during the warranty period. This warranty is only available to the original retail purchaser of
the product from the date of initial retail purchase, and is only valid with the original sales receipt, as
proof of purchase date is required to obtain warranty benets. All warranty claims must be brought
to the attention of the Company within the warranty period and no later than 30 days of the failure
to perform. This warranty does not cover normal wear or damage caused by shipping, mishandling,
misuse, accident, alteration, improper replacement parts, or other than ordinary household use.
You may be required to return the product (with shipping prepaid by you) for inspection and
evaluation. Return shipping costs are not refundable. The Company is not responsible for returns
damaged or lost in transit. Unless otherwise specically permitted by the operating instructions, this
warranty applies to indoor household use only. In order to obtain service under this warranty, please
contact the Company at the telephone number listed above or by lling out the Customer Service
Inquiry Form located at www.nostalgiaproducts.com. Warranty valid only in USA and Canada.
This warranty is in lieu of all other warranties, expressed or implied, including warranties of
merchantability and tness for a particular purpose, which are hereby excluded to the extent
permitted by law. In no event shall the Company be liable for any indirect, incidental, consequential,
or special damages arising out of or in connection with this product or the use thereof. Some
states, provinces or jurisdictions do not permit the exclusion or limitation of incidental or
consequential damages, so the foregoing exclusion or limitation may not apply to you.
This warranty does not apply to re-manufactured merchandise.
Please read the operating instructions carefully. Failure to comply
with the operating instructions will void this warranty.
For more information, visit us online at www.nostalgiaproducts.com.
Like us on Facebook at www.facebook.com/NostalgiaElectrics.
Follow our boards on Pinterest at www.pinterest.com/nostalgiaelctrx.
Tweet along with us on Twitter at www.twitter.com/NostalgiaElctrx.

13
ESPAÑOL
13
¡Convierta todos los días en una etsa!
Visite www.nostalgiaproducts.com para
ver más productos divertidos.
CONTENIDO
SEGURIDAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
PROTECCIONES IMPORTANTES . . . . . . . . . . . . . . . . . . . . . . . . . .14
PROTECCIONES IMPORTANTES ADICIONALES . . . . . . . . . . . . . . . . . 15
INTRODUCCIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
PARTES Y ENSAMBLAJE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
CÓMO FUNCIONA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
CONSEJOS ÚTILES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
LIMPIEZA Y MANTENIMIENTO . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
DEVOLUCIONES Y GARANTÍA . . . . . . . . . . . . . . . . . . . . . . . . . . .24
SEGURIDAD
Especicaciones del electrodoméstico:
120 Volts, 60 Hertz, 425 Watts
ESTE PRODUCTO ES PARA USO EN SALIDA 120V AC SOLAMENTE.
Visite www.nostalgiaproducts.com/user-manuals/ para ver el manual más actualizado.
Su seguridad y la de otras personas es muy importante.
Hemos proporcionado numerosos mensajes de seguridad importantes en este manual
y en su electrodoméstico. Siempre lea y obedezca todos los mensajes de seguridad.
Este es el símbolo de alerta de seguridad.
Este símbolo le avisa de los peligros potenciales
que pueden matar o herir a otros.
Todos los mensajes de seguridad estarán antecedidos por el símbolo de alerta.
Todos los mensajes de seguridad le dirán de qué peligro potencial se trata, cómo reducir
la posibilidad de lesiones y qué puede ocurrir si no se obedecen las instrucciones.

14
ESPAÑOL
14
PROTECCIONES IMPORTANTES
Una persona que no haya leído y comprendido todas las instrucciones
de uso y seguridad no está calicada para utilizar este aparato. Todos
los usuarios de este dispositivo deben leer y comprender este Manual
de instrucciones antes de utilizar o limpiar este aparato.
Cuando se utiliza aparatos eléctricos, siempre se deben seguir algunas
medidas básicas de seguridad que incluyen las siguientes:
1. Lea todas las instrucciones antes de utilizar este aparato.
2. NO TOQUE las supercies calientes. Use agarraderas o mangos.
3. Este aparato NO ES UN JUGUETE.
4. Este electrodoméstico no está diseñado para ser utilizado por personas (incluidos niños)
con capacidades físicas, sensoriales o mentales reducidas, o con falta de experiencia
y conocimiento, a menos que estén supervisados e instruidos sobre el uso del
electrodoméstico por una persona responsable de su seguridad. Es necesaria una estrecha
supervisión cuando cualquier electrodoméstico es utilizado por niños o cerca de ellos.
Los niños deben ser supervisados para asegurarse de que no jueguen con el aparato.
5. Una supervisión estricta se requiere cuando un aparato se use por niños o cerca de ellos.
6. Apague el aparato, luego desenchúfelo de la toma de corriente cuando no esté en
uso, antes de armar o desarmar piezas y antes de limpiarlo. Para desconectar, tome
el enchufe y tire de la toma de corriente. Nunca tire del cable de alimentación.
7. No opere ningún electrodoméstico con un cable o enchufe dañado o después
de un mal funcionamiento del electrodoméstico, o si se cae o se daña de
alguna manera. Póngase en contacto con el fabricante en su número de
teléfono de servicio al cliente para obtener información sobre el examen,
reparación o ajuste. El número de servicio al cliente es [phone].
8. Como medida de protección contra el riesgo de descarga eléctrica, no sumerja el
cable, los enchufes ni ninguna otra parte de la unidad en agua ni en otros líquidos.
9. Desconéctelo del tomacorriente cuando no esté en uso, antes de
retirar piezas y antes de la limpieza. Déjelo enfriar antes de colocar
o retirar cualquiera de las piezas, y antes de la limpieza.
10. NO utilice ningún aparato con el cable o el enchufe dañados, ni después de que el
aparato funcione mal o SI el aparato se ha dañado de cualquier manera. Devuelva
el aparato al taller de reparación más cercano para su reparación o ajuste.
11. El fabricante no recomienda el uso de aditamentos accesorios diferentes de los
proporcionados por el fabricante. El uso de accesorios puede provocar lesiones.
12. NO utilice el aparato para usos no previstos.
13. NO utilice el aparato al aire libre. SÓLO PARA USO DOMÉSTICO.
14. NO lo coloque sobre una hornilla caliente, ni eléctrica ni de gas,
ni en un horno caliente ni cerca de ninguno de estos.
15. NO permita que el cable cuelgue sobre el borde de la mesa o
del mostrador, ni que toque supercies calientes.
16. NUNCA deje la unidad desatendida mientras esté en uso ni
cuando esté enchufada a una toma de corriente.
17. Siempre conecte primero el enchufe al aparato, luego enchufe el cable
a la toma de corriente. Para desconectar, mueva todos los controles
a“apagado”, luego retire el enchufe del tomacorriente.

15
ESPAÑOL
15
PROTECCIONES IMPORTANTES ADICIONALES
Precauciones de seguridad operativa
1. Antes del uso, este dispensador debe ensamblarse correctamente
e instalarse de acuerdo con este manual.
2. Este dispensador se destina solamente para dispensar agua. NO USE otros líquidos. NO
USE para otros propósitos. Nunca use otros líquidos en el dispensador que no sean agua
embotellada conocida y segura según criterios microbiológicos. La garantía quedará
invalidada si se usa con cualquier otro líquido, tal como café, té, jugos, cerveza o vino.
Instrucciones para el cable eléctrico y el enchufe
1. El aparato tiene un enchufe polarizado (una patita más ancha). Se diseñó para
reducir el riesgo de descarga eléctrica, dado que entra en un tomacorriente
polarizado solo en una posición. Si el enchufe no entra completo en el
tomacorriente, inviértalo. Si aún así no entra, comuníquese con un
electricista calicado. No modique el enchufe de ninguna manera.
2. Se provee un cable de alimentación corto para reducir el riesgo
resultante de enredarse o tropezar con un cable largo.
3. Si se utiliza un cable alargador o un cable de alimentación más largo:
• Unos cables de extensión se pueden utilizar si se tiene cuidado con su uso.
• Las características nominales del grupo de cables o del cable de
extensión deben ser al menos iguales a las del aparato.
• Cuando se utiliza un cable largo o cable de extensión, asegúrese de
que el cable no sobresalga de la encimera ni una mesa ya que se
puede halar o tropezarse con el cable involuntariamente.
4. El fabricante no recomienda el uso de esta máquina en países que no admiten 120 V
CA incluso si se está usando un adaptador, transformador o convertidor de voltaje.
¡GUARDE ESTAS INSTRUCCIONES!

16
ESPAÑOL
16
INTRODUCCIÓN
¡Gracias por comprar el REFRIGERADOR DE AGUA AUTOLIMPIABLE DE CARGA INFERIOR
DE AGUA CALIENTE Y FRÍA de IGLOO! ¡Con el enfriador de agua de carga inferior fría y
caliente Igloo, la facilidad está al alcance de tu mano! ¡Este cargador inferior le brinda
agua helada y caliente en solo segundos! ¡Este enfriador de agua le permite cargar
botellas de 3 o 5 galones sin necesidad de plomería! Hay un bloqueo de seguridad para
niños para el botón de acceso rápido para que no haya accidentes. ¡Satisface tu sed con
agua fría o relájate con una bebida caliente con la marca en la que puedes conar!
• Enfriador de carga inferior para agua fría y caliente.
• Luz indicadora LED sin agua con luz nocturna
• La tecnología de autolimpieza con ozono ayuda a prevenir la formación de bacterias
• Utiliza botellas estándar de 3 y 5 galones (no incluidas)
• Conexión directa a la línea de agua disponible
• Patas niveladoras traseras ajustables
• Pulsadores de calor y frío y dos espigas separadas con bloqueo
de seguridad para niños para botón de acceso
• Protección contra sobrecalentamiento para tanque caliente
• Bandeja de goteo de acero inoxidable extraíble para una fácil limpieza.
• Área de dispensación adecuada para botellas de hasta 8 "
• Capacidad del tanque de agua caliente: 1.2L / Capacidad del tanque de agua fría: 4L
• Temperatura del agua: Caliente 200 ° F / Frío 40 ° F
• Interruptores de encendido / apagado de LED caliente y frío
• Enfriamiento del compresor

17
ESPAÑOL
17
PIEZAS Y ENSAMBLAJE
PIEZAS
1, 2
3
4
7
5
1 / 2- Espita de agua fría y caliente
3- Bandeja de goteo extraíble de la habitación
4- Bombas de sifón / cubierta (retráctil)
5- Botón de agua caliente / bloqueo de seguridad
6- Botón de agua fría
7- Interruptor de encendido / apagado de agua
caliente
8- Interruptor de encendido / apagado de agua fria
9- Interruptor de luz LED
6
8
9

18
ESPAÑOL
18
CÓMO FUNCIONA
ADVERTENCIA: Esta unidad está diseñada para la dispensación de agua solamente.
NO utilice otros líquidos. NO la use para otros nes. La garantía será anulada si
se usa con cualquier otro líquido como café, té, jugos, cerveza o vino.
Este dispensador ha sido diseñado para usar botellas de agua con una
capacidad de 3 o 5 galones. NO use botellas alternativas.
Conguración inicial
NOTA: Asegúrese de que los interruptores estén ENCENDIDOS. Ambos el de agua caliente y
fría, y los interruptores de luz LED se localizan en la parte posterior del enfriador de agua.
1. Retire el sello de manipulación de la tapa de la botella y retire la tapa.
2. Coloque la bomba de sifón dentro del enfriador de agua y asegúrese de que la
tapa esté bien colocada y póngala dentro de la puerta del enfriador de agua.
3. Enchufe el cable a un toma-corriente de pared con conexión a tierra adecuada.
ADVERTENCIA: Asegúrese siempre de que el cable esté lejos de una fuente de agua.
ENSAMBLE
Tenga SUMO CUIDADO cuando manipule el aparato. Cuando se saca del empaque,
se recomienda colocar la caja con cuidado sobre su lado. En su mayor parte, el
DISPENSADOR DE AGUA CALIENTE Y FRÍA DE CARGA SUPERIOR está ensamblado.
Una vez desempacado y en posición vertical, se deberá insertar la bandeja de goteo.
Requisitos de ubicación:
1. Instálelo en un área donde esté protegido de los
elementos, incluso de la luz solar directa.
2. Instálelo y úselo solamente sobre una supercie dura, plana y nivelada.
3. NO coloque el dispensador dentro de un espacio encerrado o gabinete.
4. Ubique el dispensador no más cerca de 10 centímetros de la pared con al menos
10 centímetros de holgura en los lados para permitir el libre ujo del aire.
5. El mantenimiento debe realizarlo solamente un técnico certicado.
ENFRIADORES DE AGUA
Es muy fácil reemplazar los enfriadores de 3 o 5 galones (no incluidos). NOTA:
Peligro de peso excesivo - es recomendable utilizar dos o más personas
para mover e instalar botellas. De lo contrario, puede provocar lesiones.
1. Abre la puerta del gabinete en la parte inferior y retira la tapa del enfriador de agua.
2. Coloca la bomba de sifón dentro de la botella de agua para que toque la parte inferior.
3. Asegúrate de que la tapa de la bomba de sifón se ajuste rmemente sobre
la parte superior de la botella de agua, asegurando que no haya fugas.
NOTA: La bomba de sifón es ajustable. Ajusta la longitud tirando de la porción del tubo
a su extensión máxima. Inserta la sonda dentro de la botella y empújala hacia abajo.
4. La sonda se auto-ajustará a su longitud adecuada.