IGMI GRC Series User manual

GRC Series Storage Rack
TOOLS REQUIRED FOR ASSEMBLY
Electric Hand Drill, Phillips Head Bit, 3/8" Magnetic Hex
Driver Bit. 3/8” Open end wrench.
BEFORE ASSEMBLING THE WORKBENCH
Read through the assembly instructions to familiarize
yourself with the order in which the parts are
assembled.
We suggest that you clear & vacuum the area where
the bench is to be assembled.
It is important that the bench is assembled in the
same sequence as instructed.
HARDWARE
All assembly hardware is provided.
Universal
Top/Bottom Pan
Back Panel
End Panel
Universal
Top/Bottom Pan
Upright Frame
Upright Frame
Shelf
GR Shelf Clip

Add-On
Upright Frame
STEP 1
STEP 2
Continue the installation by attaching each
add-on section. Using (4) 1/4-20 1/2” bolts
attach top and bottom pans to the add-on
right hand side upright frame. Ensure upright
is positioned correctly by top indicator. Using
(4) 1/4-20 1/2“ bolts attach left side of add-on
to right side of starter unit. Repeat these
steps for each remaining add-on unit.
Begin by choosing your assembly location
carefully. As the entire rack will be quite
cumbersome to move once partially
assembled. You will be required to access
the back of the rack sections to install the
back panels. Keep this in mind when
choosing where to begin your assembly.
Begin by attaching the universal
top/bottom pans to your first set of
uprights. The top of the upright is
identified by the small hole on the face of
the upright (as indicated on illustration).
Bolt (4) 1/4-20 1/2” Flange head bolts into
the pre installed nuts on ends of the
univeral top/bottom pans as shown.
Repeat for oposite side upright.
1/4-20 x 1/2”
Flange Head Bolt
Upright Frame
Upright Frame
Universal
top/bottom
Universal
top/bottom
x8
Upright Top
Indication Punch
1/4-20 x 1/2”
Flange Head Bolt
x8 (per add-on unit)
Continue the installation by attaching each
add-on section. Using (4) 1/4-20 1/2” bolts
attach top and bottom pans to the add-on
right hand side upright. Using (4) 1/4-20 1/2“
bolts attach left side of add-on to right side of
starter unit. Repeat these steps for each
remaining add-on unit.
Install the end panels by positioning the
panel as shown and resting the weight of the
panel on the ground. With 2 people, lift the
panel slightly off the ground to catch the
formed steel hook into the square holes in
the upright. This may take a couple attempts
to ensure all hooks are engaged. Secure the
end panels through the attachment holes
using the provided (6) #8 x 5/8” Machine
screws and lock nuts.
Starter Unit Universal
top/bottom

STEP 3STEP 4
Install the back panel with one person in the front
and one in the back. Position the back panel with the
top indication hole up. If using Add-On units the
back panels will overlap as indicated in the lower
illustration. Attach the back panels as shown using
six 5/16”-18 x 3/4” Hex Head Bolts and 5/16” Lock
nuts per upright. Bolt through the back panel(s) and
through the provided holes in the rear of the upright.
Attach with lock nut to the inside of the rack.
Once all back panels are installed it is time to
position the rack in its final destination. Take great
care in this step. Depending on the length of your
rack system this may require more than 2 people.
When you have the rack in its desired final location,
anchor the rack to the floor using appropriate
fasteners for your particular flooring.
Overlapping Back
Panels
Top View
Top Side
Indicator
5/16-18 x 3/4”
Hex Head Bolt
Nylock Nut
Optional End Panels.
Install the end panels by positioning the panel as
shown and resting the weight of the panel on the
ground. With 2 people, lift the panel slightly off
the ground to catch the formed steel hooks into
the square holes in the upright. This may take a
couple attempts to ensure all hooks are engaged.
Secure the end panels through the attachment
holes using the provided (6) #8 x 5/8” Machine
screws and lock nuts.
#8 x 5/8”
Machine Screw
Nylock Nut
Attachment
hole

STEP 5
Install the shelf clips (16 per unit) into the upright slots as shown
in the illustration. Lower the shelf onto the GR shelf clips.
Continue by positioning the remaining shelf clips at the desired
height for your remaining shelves. Lower the remaining shelves
onto the clips. Continue this procedure for the remaining rack
sections.
Shelf
GR Shelf Clip