Ignition LED Cobalt Plus User manual

LED Cobalt Plus Spot 12
MANUAL
LED Cobalt Plus Spot 12
LED Cobalt Plus Spot 12
0W

1. Safety instructions
................................
1.1.
FOR SAFE AND EFFICIENT OPERATION
1.2.
Further safety instructions
1.3. Mounting
................................
2. Introduction
................................
2.1. Product overview
................................
2.2. Dimensions
................................
3. Connections
................................
3.1. Electrical connections
................................
3.2. DMX connections
................................
3.3. Pin allocation
................................
3.4.
DMX terminator diagram
4. Control................................
................................
4.1. Structure of the menu
................................
5. DMX chart
................................
6. Technical data
................................
6.1. Lux
................................
6.2. Color wheel
................................
6.3. Gobo wheels
................................
2 / 24
LED COBALT PLUS SPOT
Table of contents
................................
................................
................................
FOR SAFE AND EFFICIENT OPERATION
................................
................................
Further safety instructions
................................................................
................................
................................
................................................................
................................
................................
................................................................
................................
................................
................................
................................
................................
................................
................................
................................
................................................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
DMX terminator diagram
................................................................
................................
................................
................................
................................
................................
................................
................................
................................
................................................................
................................
................................
................................................................
................................
................................
................................................................
................................
................................
................................
................................
................................
................................
................................
LED COBALT PLUS SPOT
120W
................................
............................ 3
................................
............ 3
................................
....... 4
................................
.. 8
................................
..... 10
................................
................... 10
................................
............................ 10
................................
... 11
................................
............ 11
................................
.................. 11
................................
......................... 12
................................
....... 12
................................
............ 13
................................
............ 13
................................
...... 15
................................
19
................................
......... 19
................................
............................ 19
................................
.......................... 20

1. Safety instructions
•This
device is suitable for indoor use (not outdoors) only.
•
All modifications to the device will void the warranty.
•
Repairs are to carry out by skilled
•
Use only fuses of the same type and original parts as spare parts.
•
Protect the unit from rain and humidity to avoid fire and electric shocks.
•
Make sure to unplug the power supply before opening the housing.
1.1.
FOR SAFE AND EFFICIENT OPERATION
Be careful with heat and extreme temperature
Avoid exposing it to direct rays of the sun or near a heating appliance.
Not put it in a temperature bellow 32
Keep away from humidity, water and dust
Do not place the set in a location with high humidity or lots of dust.
Containers with water should not be placed on the set.
Keep away from sources of hum and noise
Such as transformer motor, tuner, TV set and amplifier.
To avoid placing on un-
stable l
Select a level and stable location to avoid vibration.
Do not use chemicals or volatile liquids for cleaning
Use a clean dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt.
If out of work, contact sales agency immediately
Any t
roubles arose, remove the power plug soon, and contact with an engineer for repairing,
do not open the cabinet by yourself, it might result a danger of electric shock.
Take care with the power cable
Never pull the power cable to remove the plug from the r
When not using the device for an extended period of time, be sure to disconnect the plug
from the receptacle .
3 / 24
LED COBALT PLUS SPOT
device is suitable for indoor use (not outdoors) only.
All modifications to the device will void the warranty.
Repairs are to carry out by skilled
personnel only.
Use only fuses of the same type and original parts as spare parts.
Protect the unit from rain and humidity to avoid fire and electric shocks.
Make sure to unplug the power supply before opening the housing.
FOR SAFE AND EFFICIENT OPERATION
Be careful with heat and extreme temperature
Avoid exposing it to direct rays of the sun or near a heating appliance.
Not put it in a temperature bellow 32
°F /0°C, or exceeding 104°F /40°C.
Keep away from humidity, water and dust
Do not place the set in a location with high humidity or lots of dust.
Containers with water should not be placed on the set.
Keep away from sources of hum and noise
Such as transformer motor, tuner, TV set and amplifier.
stable l
ocation
Select a level and stable location to avoid vibration.
Do not use chemicals or volatile liquids for cleaning
Use a clean dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt.
If out of work, contact sales agency immediately
roubles arose, remove the power plug soon, and contact with an engineer for repairing,
do not open the cabinet by yourself, it might result a danger of electric shock.
Take care with the power cable
Never pull the power cable to remove the plug from the r
eceptacle, be sure to hold the plug.
When not using the device for an extended period of time, be sure to disconnect the plug
LED COBALT PLUS SPOT
120W
Use only fuses of the same type and original parts as spare parts.
Protect the unit from rain and humidity to avoid fire and electric shocks.
Make sure to unplug the power supply before opening the housing.
Use a clean dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt.
roubles arose, remove the power plug soon, and contact with an engineer for repairing,
do not open the cabinet by yourself, it might result a danger of electric shock.
eceptacle, be sure to hold the plug.
When not using the device for an extended period of time, be sure to disconnect the plug

Important:
Damages caused by the disregard of this user manual are not subject to
warranty. The dealer will
not accept liability for any resulting defects or problems. Make sure
the electrical connection is carried out by qualified personnel. All electrical and mechanical
connections have to be carried out according to the European safety standards.
1.2.Further saf
ety instructions
IMPORTANT
Keep away from water and humidity!
Make sure to unplug the power supply before opening the housing!
Please read careful through this manual before the first start
All persons which are entrusted with installation,
device have to:
•
Show a corresponding competence.
•
Follow the lines of this manual.
•
Face this manual as part of the product.
•
Keep this manual over the lifetime of the product.
•
Pass this manual to new owner
•
Download the latest version of the manual.
Safety-related red flags
IMPORTANT!
Handle with the dangerous electric voltages carefully.
With this voltage there is the danger to get a life
Always observe
After taken the device from a cold room to a warm room, it is not allowed to activate the device.
It is possible that thereby emerged condensed water damages the device. Activate the device not until
it reached ambient temperature.
Prevent that the power
cable has contact with other cables. Handle carefully with power cables and
power connections. Don’t touch them with clammy hands.
4 / 24
LED COBALT PLUS SPOT
Damages caused by the disregard of this user manual are not subject to
not accept liability for any resulting defects or problems. Make sure
the electrical connection is carried out by qualified personnel. All electrical and mechanical
connections have to be carried out according to the European safety standards.
ety instructions
Keep away from water and humidity!
Make sure to unplug the power supply before opening the housing!
Please read careful through this manual before the first start
-up.
All persons which are entrusted with installation,
start-
up, operation, maintenance and repair of this
Show a corresponding competence.
Follow the lines of this manual.
Face this manual as part of the product.
Keep this manual over the lifetime of the product.
Pass this manual to new owner
s of the device.
Download the latest version of the manual.
Handle with the dangerous electric voltages carefully.
With this voltage there is the danger to get a life
-
threatening electric shock.
After taken the device from a cold room to a warm room, it is not allowed to activate the device.
It is possible that thereby emerged condensed water damages the device. Activate the device not until
cable has contact with other cables. Handle carefully with power cables and
power connections. Don’t touch them with clammy hands.
LED COBALT PLUS SPOT
120W
Damages caused by the disregard of this user manual are not subject to
not accept liability for any resulting defects or problems. Make sure
the electrical connection is carried out by qualified personnel. All electrical and mechanical
connections have to be carried out according to the European safety standards.
Make sure to unplug the power supply before opening the housing!
up, operation, maintenance and repair of this
threatening electric shock.
After taken the device from a cold room to a warm room, it is not allowed to activate the device.
It is possible that thereby emerged condensed water damages the device. Activate the device not until
cable has contact with other cables. Handle carefully with power cables and

Make sure that the voltage which is to connect not exceeds the specified values.
Make sure that it isn’t possible to squ
yourself with regular checks that there are no damages to the power cable or the device.
Don’t switch the device in short time intervals (e.g. in second cycle) on or off.
Keep away children and laymen off the device.
Health risk!
Don’t look directly into the light source. At certain circumstances it is
possible that some people get epileptic seizures. This is especially true for
individuals whose epilepsy was determined
Designated use
This device was developed for professional use on stages, in discos, theatres etc. The device is only
approved for a connection up to 230V 50/60 Hz AC voltage and only for indoor use.
Regular breaks during operation increas
Avoid convulsions or any form of forceful impact during the installation or the start
Make sure that the device is not exposed excessive heat, humidity or dust at the place of installation.
Take care that
no cables are lying around. You would endanger your own safety and also the safety of
a third party.
It is not allowed to operate or store the device in an environment in which spray water, rain, humidity
or fog is expected. Humidity or very high atmosph
and could cause deathly electric shocks. If you use fog devices the device has not be exposed to a
direct smoke jet. There has to be a safety distance of at least 0.5m between this device and the fog
m
achine. Make sure that the saturation of the fog has to enable a visibility of at least 10m.
The ambient temperature has to be between 0°C and +40°C. Avoid direct sunlight and close proximity
to heaters. You have also to attend it during the transport in closed motor vehicles.
You have to attend that with an ambient temperature von 40°C it is no
humidity exceeds 50%.
5 / 24
LED COBALT PLUS SPOT
Make sure that the voltage which is to connect not exceeds the specified values.
Make sure that it isn’t possible to squ
eeze or damage the power cable with sharp edges. Assure
yourself with regular checks that there are no damages to the power cable or the device.
Don’t switch the device in short time intervals (e.g. in second cycle) on or off.
Keep away children and laymen off the device.
Don’t look directly into the light source. At certain circumstances it is
possible that some people get epileptic seizures. This is especially true for
individuals whose epilepsy was determined
by a doctor.
This device was developed for professional use on stages, in discos, theatres etc. The device is only
approved for a connection up to 230V 50/60 Hz AC voltage and only for indoor use.
Regular breaks during operation increas
e the lifetime of your device.
Avoid convulsions or any form of forceful impact during the installation or the start
Make sure that the device is not exposed excessive heat, humidity or dust at the place of installation.
no cables are lying around. You would endanger your own safety and also the safety of
It is not allowed to operate or store the device in an environment in which spray water, rain, humidity
or fog is expected. Humidity or very high atmosph
eric humidity could reduce the isolation of the device
and could cause deathly electric shocks. If you use fog devices the device has not be exposed to a
direct smoke jet. There has to be a safety distance of at least 0.5m between this device and the fog
achine. Make sure that the saturation of the fog has to enable a visibility of at least 10m.
The ambient temperature has to be between 0°C and +40°C. Avoid direct sunlight and close proximity
to heaters. You have also to attend it during the transport in closed motor vehicles.
You have to attend that with an ambient temperature von 40°C it is no
t allowed that the relative
LED COBALT PLUS SPOT
120W
eeze or damage the power cable with sharp edges. Assure
yourself with regular checks that there are no damages to the power cable or the device.
Don’t look directly into the light source. At certain circumstances it is
possible that some people get epileptic seizures. This is especially true for
This device was developed for professional use on stages, in discos, theatres etc. The device is only
approved for a connection up to 230V 50/60 Hz AC voltage and only for indoor use.
Avoid convulsions or any form of forceful impact during the installation or the start
-up of the device.
Make sure that the device is not exposed excessive heat, humidity or dust at the place of installation.
no cables are lying around. You would endanger your own safety and also the safety of
It is not allowed to operate or store the device in an environment in which spray water, rain, humidity
eric humidity could reduce the isolation of the device
and could cause deathly electric shocks. If you use fog devices the device has not be exposed to a
direct smoke jet. There has to be a safety distance of at least 0.5m between this device and the fog
achine. Make sure that the saturation of the fog has to enable a visibility of at least 10m.
The ambient temperature has to be between 0°C and +40°C. Avoid direct sunlight and close proximity
to heaters. You have also to attend it during the transport in closed motor vehicles.
t allowed that the relative

Operate the device not during thunderstorms. Surge voltages could destroy the device. Unplug the
power supply during thunderstorms.
During the installation the use of the mounting bracket is obligatory.
Surrounding objects or surfaces should not be in contact with the device.
Make sure that during the installation and removal of the device the area below the place of
installation i
s basically cordoned off. This also applies to implementation of service.
The device has basically been protected by a suitable safety.
Make familiar yourself with the functions of the device before start
should not h
andle with the device. The most cause of functional disorder is inappropriate handling.
Do not use chemicals or volatile liquids for cleaning. Use a clean dry cloth to wipe off the dust, or a
wet soft cloth for stubborn dirt.
For transport use the origi
nal packing or designated accessory to avoid damages during the transport.
For reasons of safety unauthorized changes are forbidden.
A
usage of the device which differs from usages which are described in this manual can cause
damages of the device. In t
hat case the warranty expires. Additional you should notice that every
differed usage is related with dangers and can cause e.g. an electrical short, fire, electric shock or
crash.
Overhead installation
Danger of life!
You have to observe the
EN60598-2-
17
The suspension devices have to be build and measured so they can withstand for an hour the tenfold
of the payload without suffering a perma
6 / 24
LED COBALT PLUS SPOT
Operate the device not during thunderstorms. Surge voltages could destroy the device. Unplug the
power supply during thunderstorms.
During the installation the use of the mounting bracket is obligatory.
Surrounding objects or surfaces should not be in contact with the device.
Make sure that during the installation and removal of the device the area below the place of
s basically cordoned off. This also applies to implementation of service.
The device has basically been protected by a suitable safety.
Make familiar yourself with the functions of the device before start
-
up. People without the experience
andle with the device. The most cause of functional disorder is inappropriate handling.
Do not use chemicals or volatile liquids for cleaning. Use a clean dry cloth to wipe off the dust, or a
nal packing or designated accessory to avoid damages during the transport.
For reasons of safety unauthorized changes are forbidden.
usage of the device which differs from usages which are described in this manual can cause
hat case the warranty expires. Additional you should notice that every
differed usage is related with dangers and can cause e.g. an electrical short, fire, electric shock or
Danger of life!
You have to observe the
regulations of BGV C1 (f
ormerly VBG 70) and
17
Installations are to carry out by skilled personnel only.
The suspension devices have to be build and measured so they can withstand for an hour the tenfold
of the payload without suffering a perma
nent detrimental deformation.
LED COBALT PLUS SPOT
120W
Operate the device not during thunderstorms. Surge voltages could destroy the device. Unplug the
Make sure that during the installation and removal of the device the area below the place of
s basically cordoned off. This also applies to implementation of service.
up. People without the experience
andle with the device. The most cause of functional disorder is inappropriate handling.
Do not use chemicals or volatile liquids for cleaning. Use a clean dry cloth to wipe off the dust, or a
nal packing or designated accessory to avoid damages during the transport.
usage of the device which differs from usages which are described in this manual can cause
hat case the warranty expires. Additional you should notice that every
differed usage is related with dangers and can cause e.g. an electrical short, fire, electric shock or
ormerly VBG 70) and
Installations are to carry out by skilled personnel only.
The suspension devices have to be build and measured so they can withstand for an hour the tenfold

Basically installation has to be made by using a second separate suspension. This can be e.g. a
suitable net. The second suspension must be designed and attached so no part of the installation can
fall down in case of failure.
During construction, reconstruction and deconstruction unnecessary stay in the range of moving
areas, on lightning bridges, under elevated work stations or any other danger zones is forbidden.
The operator is obliged to following safety
- Before the first start-
up or after critical changes before restarting it has to be checked by an
expert.
-
Review in the frame of the inspection test at least all four years by an expert. .
-
Review by a qualified person at least once a year.
How to carry out the overhead installation:
In tidal fall you should install the device out of the lounge area of people
IMPORTANT!
Overhead installation requires a high level of experience. This inclu
calculating the payload, used installation material and safety inspections of the used material and the
projector whereas the required experience is not limited to this. Do not try to carry out installation
yourself under any circumstances
inappropriate installation can lead to injuries and/or damaged properties.
It is not allowed to install the device in the grip area of people.
If the device may hang from the ceiling or fro
The device may not be installed so it can swing freely in the room.
Please note: Crashing down items can cause serious injuries! Do not install the projector, if you doubt
the safety of a possible inst
allation form!
Before installation make sure that the mounting surface has the ability to carry the tenfold point load of
the own weight of the device.
Mount the device with the mounting
During
overhead installation the device must be always secured by a safety rope which is designed to
hold the twelvefold weight of device. Only safety ropes with quick
may be used. Hang up the safety rope in the hole of the mount
truss or an appropriate fastening point. Hang up the end in the fastening element and tie up the
locking nut. A safety rope once exposed to failing load or damaged may not be used furthermore.
7 / 24
LED COBALT PLUS SPOT
Basically installation has to be made by using a second separate suspension. This can be e.g. a
suitable net. The second suspension must be designed and attached so no part of the installation can
During construction, reconstruction and deconstruction unnecessary stay in the range of moving
areas, on lightning bridges, under elevated work stations or any other danger zones is forbidden.
The operator is obliged to following safety
-related and mechanical facilities:
up or after critical changes before restarting it has to be checked by an
Review in the frame of the inspection test at least all four years by an expert. .
Review by a qualified person at least once a year.
How to carry out the overhead installation:
In tidal fall you should install the device out of the lounge area of people
.
Overhead installation requires a high level of experience. This inclu
calculating the payload, used installation material and safety inspections of the used material and the
projector whereas the required experience is not limited to this. Do not try to carry out installation
yourself under any circumstances
if you are not qualified. Contact a professional installer. An
inappropriate installation can lead to injuries and/or damaged properties.
It is not allowed to install the device in the grip area of people.
If the device may hang from the ceiling or fro
m high beams, the use of truss systems is mandatory.
The device may not be installed so it can swing freely in the room.
Please note: Crashing down items can cause serious injuries! Do not install the projector, if you doubt
allation form!
Before installation make sure that the mounting surface has the ability to carry the tenfold point load of
Mount the device with the mounting
-
bracket to your trussing system using an appropriate clamp.
overhead installation the device must be always secured by a safety rope which is designed to
hold the twelvefold weight of device. Only safety ropes with quick
-
release safety fastener elements
may be used. Hang up the safety rope in the hole of the mount
ing bracket. Direct the rope over the
truss or an appropriate fastening point. Hang up the end in the fastening element and tie up the
locking nut. A safety rope once exposed to failing load or damaged may not be used furthermore.
LED COBALT PLUS SPOT
120W
Basically installation has to be made by using a second separate suspension. This can be e.g. a
suitable net. The second suspension must be designed and attached so no part of the installation can
During construction, reconstruction and deconstruction unnecessary stay in the range of moving
areas, on lightning bridges, under elevated work stations or any other danger zones is forbidden.
up or after critical changes before restarting it has to be checked by an
Review in the frame of the inspection test at least all four years by an expert. .
Overhead installation requires a high level of experience. This inclu
des knowledge of
calculating the payload, used installation material and safety inspections of the used material and the
projector whereas the required experience is not limited to this. Do not try to carry out installation
if you are not qualified. Contact a professional installer. An
m high beams, the use of truss systems is mandatory.
Please note: Crashing down items can cause serious injuries! Do not install the projector, if you doubt
Before installation make sure that the mounting surface has the ability to carry the tenfold point load of
bracket to your trussing system using an appropriate clamp.
overhead installation the device must be always secured by a safety rope which is designed to
release safety fastener elements
ing bracket. Direct the rope over the
truss or an appropriate fastening point. Hang up the end in the fastening element and tie up the
locking nut. A safety rope once exposed to failing load or damaged may not be used furthermore.

The maximum drop exceed
must not exceed 20cm.
A safety rope once exposed to failing load or damaged may not be used furthermore.
Adjust the desired inclination angle via the mounting bracket and tighten the screw.
The lamp which is used in this device is a gas discharge lamp.
at least 15 minutes before turn it on again. Fast on and off of the lamp reduces the lifetime drastic.
Breaks increase the lifetime.
1.3.Mounting
Basically you can operate the device in every position
Take care of the CE regulations! The installation should be made by professionals.
8 / 24
LED COBALT PLUS SPOT
must not exceed 20cm.
A safety rope once exposed to failing load or damaged may not be used furthermore.
Adjust the desired inclination angle via the mounting bracket and tighten the screw.
The lamp which is used in this device is a gas discharge lamp.
If you turn off the lamp you have to wait
at least 15 minutes before turn it on again. Fast on and off of the lamp reduces the lifetime drastic.
Basically you can operate the device in every position
Take care of the CE regulations! The installation should be made by professionals.
LED COBALT PLUS SPOT
120W
A safety rope once exposed to failing load or damaged may not be used furthermore.
Adjust the desired inclination angle via the mounting bracket and tighten the screw.
If you turn off the lamp you have to wait
at least 15 minutes before turn it on again. Fast on and off of the lamp reduces the lifetime drastic.
Take care of the CE regulations! The installation should be made by professionals.

9 / 24
LED COBALT PLUS SPOT
LED COBALT PLUS SPOT
120W

2. Introduction
Thank you for buying the
LED Cobalt
For a successful installation
and operation, please
2.1.Product overview
1. Head
2. Arm
3. Base
4. 3-Pin XLR female
5. 5-Pin XLR female
2.2.Dimensions
10 / 24
LED COBALT PLUS SPOT
LED Cobalt
Plus Spot 120W. It is a powerful device.
and operation, please
read this manual carefully.
6. Power switch
7. Power socket
8. Fuse
9. 3-Pin XLR male
10. 5-Pin XLR male
LED COBALT PLUS SPOT
120W

3. Connections
3.1.Electrical
connections
If you wish to change the power supply settings, see the chapter Appendix. Connect the fixture to the
mains with the enclosed power cable and plug. The earth has to be connected.
Cable (EU)
Cable (US)
Brown Black
Light blue White
Yellow/Green Green
3.2.DMX connections
To make a DMX512 connection go ahead like it is described in the picture. Make sure that you use
shielded cable. 3pole or 5pole XLR cables are suitable.
Important!
After the last device the line has to be terminated. In order to do this you have to solder a
120Ω
resistor between the pins Data + and Data
XLR: Plug this adapter into the DMX output of the device.
11 / 24
LED COBALT PLUS SPOT
connections
If you wish to change the power supply settings, see the chapter Appendix. Connect the fixture to the
mains with the enclosed power cable and plug. The earth has to be connected.
Cable (US)
Pin
International
Live L
Neutral N
Earth
To make a DMX512 connection go ahead like it is described in the picture. Make sure that you use
shielded cable. 3pole or 5pole XLR cables are suitable.
After the last device the line has to be terminated. In order to do this you have to solder a
resistor between the pins Data + and Data
-
. You can solder this end resistor on a 3pin or 5pin
XLR: Plug this adapter into the DMX output of the device.
LED COBALT PLUS SPOT
120W
If you wish to change the power supply settings, see the chapter Appendix. Connect the fixture to the
International
To make a DMX512 connection go ahead like it is described in the picture. Make sure that you use
After the last device the line has to be terminated. In order to do this you have to solder a
. You can solder this end resistor on a 3pin or 5pin

3.3.Pin allocation
3.4.DMX
terminator diagram
12 / 24
LED COBALT PLUS SPOT
terminator diagram
At installation where the cable has to span long
distances, or can be disturbed by other cables, it is
useful to use end resistors. The DMX terminator is a
XLR plug which has a 120Ω
resistor between pin2 and
pi
n3. This is plugged in the last device of a DMX
chain.
LED COBALT PLUS SPOT
120W
At installation where the cable has to span long
distances, or can be disturbed by other cables, it is
useful to use end resistors. The DMX terminator is a
resistor between pin2 and
n3. This is plugged in the last device of a DMX

4. Control
Using touch control switch and LCD display, and this can be simply and easily set the address code
and functions code.
If you view or modify the lighting feature set, then press MODE
menu interface. Both there is a sub menu corresponding to the functional operation of the main menu.
Each of the menus is representative of the specific features of the lamp. The specific content shows
as the table me
nu below. Set or browse lighting function, press UP or DOWN button.
Press ENTER to save your changes or enter the submenu. Press the UP or DOWN can change the
numerical (increase or decrease in value).
Press the MODE button to return to menu.
4.1.Structure of the
menu
Function
Addr
Value
Auto
Music
Info
Time
Temp
Product
Personal Status
13 / 24
LED COBALT PLUS SPOT
Using touch control switch and LCD display, and this can be simply and easily set the address code
If you view or modify the lighting feature set, then press MODE
button, the LCD display will enter the
menu interface. Both there is a sub menu corresponding to the functional operation of the main menu.
Each of the menus is representative of the specific features of the lamp. The specific content shows
nu below. Set or browse lighting function, press UP or DOWN button.
Press ENTER to save your changes or enter the submenu. Press the UP or DOWN can change the
numerical (increase or decrease in value).
Press the MODE button to return to menu.
menu
001-xxx
Free Ch
Alone
Master
OFF
Alone
Master
Off
Current
xxxx
Total
xxxx
Clear
ON/OFF
Head T
xxxx
Product
Vxx
Addr DMX
ON/OFF
No DMX
Clos
Hold
Auto
Musi
Pan R
ON/OFF
Tilt R
ON/OFF
DMX Mod
Mod1/Mod2
Feed
ON/OFF
Mic
70, 0
LED COBALT PLUS SPOT
120W
Using touch control switch and LCD display, and this can be simply and easily set the address code
button, the LCD display will enter the
menu interface. Both there is a sub menu corresponding to the functional operation of the main menu.
Each of the menus is representative of the specific features of the lamp. The specific content shows
nu below. Set or browse lighting function, press UP or DOWN button.
Press ENTER to save your changes or enter the submenu. Press the UP or DOWN can change the
xxxx
xxxx
ON/OFF
xxxx
ON/OFF
Clos
Hold
Auto
Musi
ON/OFF
ON/OFF
Mod1/Mod2
ON/OFF
70, 0
-99

Display
Default
Reset
All
Pan/Tilt
Col
Gobo
Else
Adjust
Test
Regulate
14 / 24
LED COBALT PLUS SPOT
Display
Close T
05, 02
Rev
ON/OFF
Default
Pan/Tilt
Pan…….xxx
xxx
Regulate
Sn
xxx
Pan
xxx
LED COBALT PLUS SPOT
120W
05, 02
-59
ON/OFF
xxx
xxx
xxx

5. DMX chart
Mode 1 Mode 2
Value
from
1 1 0
2 0
3 2 0
4 0
5 3
0
226
236
246
6 4
0
15
30
45
60
75
95
105
120
128
188
194
7 5
0
10
20
30
40
50
60
70
80
15 / 24
LED COBALT PLUS SPOT
Value to Function
255 Pan
255 Pan fine
255 Tilt
255 Tilt fine
Speed Pan/Tilt
225 Speed Pan/Tilt fast-slow
235 Blackout by movement
245 Blackout by all wheel changing
255 No function
Color wheel
14 White
29 Color 1
44 Color 2
59 Color 3
74 Color 4
94 Color 5
104 Color 6
119 Color 7
127 Color 8
187 Rainbow effect forwards fast-
slow
193 No rotation
255 Rainbow effect backwards slow-
fast
Gobo wheel 1
9 Open
19 Gobo 1
29 Gobo 2
39 Gobo 3
49 Gobo 4
59 Gobo 5
69 Gobo 6
79 Gobo 7
99 Shake Gobo 1 slow-fast
LED COBALT PLUS SPOT
120W
slow
fast

100
120
140
160
180
200
220
8 6
0
9
128
136
9 7
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
10 8 0
4
16 / 24
LED COBALT PLUS SPOT
119 Shake Gobo 2 slow-fast
139 Shake Gobo 3 slow-fast
159 Shake Gobo 4 slow-fast
179 Shake Gobo 5 slow-fast
199 Shake Gobo 6 slow-fast
219 Shake Gobo 7 slow-fast
255 Gobo rotation slow-fast
Gobo rotation
8 No rotation
127 Gobo rotation forwards fast-slow
135 No rotation
255 Gobo rotation backwards slow-
fast
Gobo wheel 2
9 Open
19 Gobo 1
29 Gobo 2
39 Gobo 3
49 Gobo 4
59 Gobo 5
69 Gobo 6
79 Gobo 7
89 Gobo 8
99 Gobo 9
109 Shake Gobo 1 slow-fast
119 Shake Gobo 2 slow-fast
129 Shake Gobo 3 slow-fast
139 Shake Gobo 4 slow-fast
149 Shake Gobo 5 slow-fast
159 Shake Gobo 6 slow-fast
169 Shake Gobo 7 slow-fast
179 Shake Gobo 8 slow-fast
189 Shake Gobo 9 slow-fast
255 Gobo rotation slow-fast
3-way prism
3 No function
63 Rotation forwards fast-slow
LED COBALT PLUS SPOT
120W
fast

64
68
128
136
144
152
160
168
176
184
192
200
208
216
224
232
240
11 9 0
12 10
0
1
96
128
160
192
224
13 11 0
14 12
0
20
40
80
85
88
91
94
97
17 / 24
LED COBALT PLUS SPOT
67 No rotation
127 Rotation backwards slow-fast
135 Macro 1
143 Macro 2
151 Macro 3
159 Macro 4
167 Macro 5
175 Macro 6
183 Macro 7
191 Macro 8
199 Macro 9
207 Macro 10
215 Macro 11
223 Macro 12
231 Macro 13
239 Macro 14
255 Macro 15
255 Focus
Shutter
No function
95 Strobe slow-fast
127 Open
159 Pulse effect
191 Open
223 Random strobe slow-fast
255 Open
255 Dimmer 0-100%
19 Color change normal
39 Color change to any position
79 No function
84 Motor reset (all)
87 No function
90 Motor reset (Color)
93 Motor reset (Gobo)
96 No function
99 Motor reset (other)
LED COBALT PLUS SPOT
120W

100
120
140
160
180
200
220
240
18 / 24
LED COBALT PLUS SPOT
119 Internal program 1
139 Internal program 2
159 Internal program 3
179 Internal program 4
199 Internal program 5
219 Internal program 6
239 Internal program 7
255 Internal program 8
LED COBALT PLUS SPOT
120W

6. Technical data
Voltage
Power consumption
Light source
Weight
6.1.Lux
6.2.Color wheel
19 / 24
LED COBALT PLUS SPOT
AC100-250V 50/60 Hz
212W
High Power 120W LED
18,5kg
LED COBALT PLUS SPOT
120W

6.3.Gobo wheels
20 / 24
LED COBALT PLUS SPOT
LED COBALT PLUS SPOT
120W