Ihome Ib85 User manual

Model: iB85 English I/B (Front)

Print color : Black text on white paper

Size of manual: 180W x 270H (mm)

Date: Aug 29, 2013

Wearing Your Headphones

Your iHome iB85 Bluetooth headphones are supplied with padded ear cushions for long

wearing comfort. The headband can be extended to accommodate almost any head

size. There are ‘L’ and ‘R’ markings on the inside of the headband. When the headphones

are worn properly the controls will be on your left ear.

Using Your Headphones

Note: Some of the functions described below may not be supported on your speciﬁc

smartphone. Check with your smartphone owner’s manual to conﬁrm the features

supported by your phone.

Your headphones must be paired with your phone and turned on to perform any of the

following operations.

Receiving/Ending A Call

When you receive an incoming call, press the Multi-function button once to answer the

call through the headphones. When you are ﬁnished speaking press the Multi-function

button once more to end/disconnect the call.

To transfer a call between the headphones and the smartphone quickly press the

Multi-function button twice.

Making A Call

When you make a call on your smartphone the call may be automatically transferred to

the headphones if your smartphone supports this automatic transfer function. If not,

quickly press the Multi-function button twice to transfer the call to the headphones.

Voice Activated Calling

If your smartphone supports this feature with the headphones, press and hold the

Multi-function button for about 2 seconds to initiate the voice activated calling function,

then follow the instructions supplied with your phone.

Last Number Redial

If your phone supports this feature, quickly press the Multi-function button twice to redial

the last number you called.

Declining A Call

If you receive a call that you would rather not accept (indicated by the caller ID on your

phone) quickly press the Multi-function button twice to decline the call.

Volume Control

Press the Volume “ +” or “ –” to adjust the volume of the incoming calls or the music

volume level.

Introduction

Your new iHome Bluetooth stereo headphones are designed to link with your Bluetooth

enabled device to allow you to wirelessly listen to music and answer phone calls within

the normal 10 meter (30 feet) Bluetooth operating range. Your headphones also feature

DSP (Digital Signal Processing) for enhanced audio plus noise reduction and echo

cancellation circuitry.

What’s Included

• Bluetooth Stereo Headphones with Folding Headband

• USB Charging Cable

• Travel Pouch

Speciﬁcations

Bluetooth speciﬁcation: Supports V2.1+ EDR with Handsfree Proﬁle 1.0,

Headset Proﬁle 1.1 and A2DP proﬁle 1.2 (Class ll)

and Audio/Video Remote Control Proﬁle AVRP

Standby time: up to 360 hours (with fully charged battery)

Talk time: up to 12 hours (with fully charged battery)

Music Playing time: up to 12 hours (with fully charged battery)

Operating Distance: up to 10 meters / 30 feet

Certiﬁcations: CE, FCC, RoHS, BQB

Pairing With a Bluetooth Enabled Device For The First Time

If your smartphone, laptop, or music player, such as the iPod touch, is Bluetooth enabled

(supports the A2DP Bluetooth Proﬁle) you may pair these iHome headphones with your

device to listen to music and make or receive calls as long as the two devices are within

the Bluetooth operating range of approximately 30 feet of each other.

1. Make sure that your Bluetooth enabled device is ‘On’.

2. Press and hold the Multi-function button on your iB85 headphone for about 7 seconds

until the blue LED ﬂashes rapidly. This indicates that the iB85 has entered the 'pairing

mode'. (NOTE: If no device is paired within 3 minutes, the iB85 will exit the pairing

mode.)

3. Turn on the Bluetooth function of your device so that it begins searching for a

compatible device.

4. “iHome iB85” should appear on your laptop, phone or music player’s compatible

devices list. You may also see a message such as “Not Paired”. Tap on that message

to complete the pairing process. If your device asks for a ‘password’ to complete the

pairing process, enter ‘0000’ on the keypad of your device.

5. When pairing is successful the screen on your device should show “iHome iB85

Connected” or similar message and the blue LED indicator on the iB85 headphones

will remain ‘On’. Your headphones are now ready for use.

Auto-Linking With A Previously Paired Device

If your iB85 headphones were previously paired with a Bluetooth enabled device, your

headphones will attempt to auto-link with that device again whenever that device is within

the Bluetooth operating range.

1. Press and hold the Multi-function button on your iB85 headphones for about 4

seconds until the blue LED indicator slowly ﬂashes to indicate the headphones are in

the ‘Standby’ mode and searching for a previously paired device.

2. Make sure that the Bluetooth function of the previously paired device is ‘On’.

Note: If no previously paired device is found after 5 minutes the auto-linking function

stops and your iB85 headphones shut off automatically to preserve the battery life.

Switching the Power On and Off

1. Press and hold the Multi-function button for approximately 4 seconds until you hear

the power up tone. The LED indicator turns solid blue if linked or blinking blue if not

linked. This indicates that the power is ‘On’.

2. When the power is ‘On’ press and hold the Multi-function button for approximately 3

seconds until you hear the power down tone. The LED indicator brieﬂy turns red and

then shuts off. This indicates that the power is ‘Off’.

Model: iB85

Bluetooth wireless

headphones with mic

+ remote and pouch

Controls and Indicators

1. Multi-function button: Power On/Off,

Answer/End, Play/Pause, Pair

2. Power/Charging/Pairing Indicator

3. Volume +button

4. Volume

button

5. Microphone

6. Forward button

7. Back button

8. Micro USB Charging Port

(located under moisture resistant cover)

Charging Your Headphones

IMPORTANT: Your headphones operate on a built-in rechargeable lithium-ion battery. You

should charge the battery for a full 4 hours before ﬁrst time use.

1. Lift up the moisture resistant cover to expose the micro USB charging port.

2. Connect the micro USB plug on the charging cable to the micro USB port on the

headphones.

3. Connect the standard USB plug on the charging cable to any standard USB power

port such as found on a notebook computer, or the charging adapter for an iPod,

iPhone, etc.

4. The headphone will be automatically powered off once USB cable is connected.

Throughout the charging process, headphone remains off.

5. The Power/Charging/Pairing indicator will slowly ﬂash while the headphone is

charging. The indicator will turn Off when the battery is fully charged. It is

recommended not to leave the headphones charging for more than 5 hours

unattended.

Reminder: Allow the battery to charge for 4 hours before ﬁrst time use. Normal recharge

time after ﬁrst use should take about 3 hours. When fully charged the battery will provide

up to 12 hours of working time, or 360 hours of standby time.

Model: iB85 English I/B (Front)

Print color : Black text on white paper

Size of manual: 180W x 270H (mm)

Date: Aug 29, 2013

Wearing Your Headphones

Your iHome iB85 Bluetooth headphones are supplied with padded ear cushions for long

wearing comfort. The headband can be extended to accommodate almost any head

size. There are ‘L’ and ‘R’ markings on the inside of the headband. When the headphones

are worn properly the controls will be on your left ear.

Using Your Headphones

Note: Some of the functions described below may not be supported on your speciﬁc

smartphone. Check with your smartphone owner’s manual to conﬁrm the features

supported by your phone.

Your headphones must be paired with your phone and turned on to perform any of the

following operations.

Receiving/Ending A Call

When you receive an incoming call, press the Multi-function button once to answer the

call through the headphones. When you are ﬁnished speaking press the Multi-function

button once more to end/disconnect the call.

To transfer a call between the headphones and the smartphone quickly press the

Multi-function button twice.

Making A Call

When you make a call on your smartphone the call may be automatically transferred to

the headphones if your smartphone supports this automatic transfer function. If not,

quickly press the Multi-function button twice to transfer the call to the headphones.

Voice Activated Calling

If your smartphone supports this feature with the headphones, press and hold the

Multi-function button for about 2 seconds to initiate the voice activated calling function,

then follow the instructions supplied with your phone.

Last Number Redial

If your phone supports this feature, quickly press the Multi-function button twice to redial

the last number you called.

Declining A Call

If you receive a call that you would rather not accept (indicated by the caller ID on your

phone) quickly press the Multi-function button twice to decline the call.

Volume Control

Press the Volume “ +” or “ –” to adjust the volume of the incoming calls or the music

volume level.

Introduction

Your new iHome Bluetooth stereo headphones are designed to link with your Bluetooth

enabled device to allow you to wirelessly listen to music and answer phone calls within

the normal 10 meter (30 feet) Bluetooth operating range. Your headphones also feature

DSP (Digital Signal Processing) for enhanced audio plus noise reduction and echo

cancellation circuitry.

What’s Included

• Bluetooth Stereo Headphones with Folding Headband

• USB Charging Cable

• Travel Pouch

Speciﬁcations

Bluetooth speciﬁcation: Supports V2.1+ EDR with Handsfree Proﬁle 1.0,

Headset Proﬁle 1.1 and A2DP proﬁle 1.2 (Class ll)

and Audio/Video Remote Control Proﬁle AVRP

Standby time: up to 360 hours (with fully charged battery)

Talk time: up to 12 hours (with fully charged battery)

Music Playing time: up to 12 hours (with fully charged battery)

Operating Distance: up to 10 meters / 30 feet

Certiﬁcations: CE, FCC, RoHS, BQB

Pairing With a Bluetooth Enabled Device For The First Time

If your smartphone, laptop, or music player, such as the iPod touch, is Bluetooth enabled

(supports the A2DP Bluetooth Proﬁle) you may pair these iHome headphones with your

device to listen to music and make or receive calls as long as the two devices are within

the Bluetooth operating range of approximately 30 feet of each other.

1. Make sure that your Bluetooth enabled device is ‘On’.

2. Press and hold the Multi-function button on your iB85 headphone for about 7 seconds

until the blue LED ﬂashes rapidly. This indicates that the iB85 has entered the 'pairing

mode'. (NOTE: If no device is paired within 3 minutes, the iB85 will exit the pairing

mode.)

3. Turn on the Bluetooth function of your device so that it begins searching for a

compatible device.

4. “iHome iB85” should appear on your laptop, phone or music player’s compatible

devices list. You may also see a message such as “Not Paired”. Tap on that message

to complete the pairing process. If your device asks for a ‘password’ to complete the

pairing process, enter ‘0000’ on the keypad of your device.

5. When pairing is successful the screen on your device should show “iHome iB85

Connected” or similar message and the blue LED indicator on the iB85 headphones

will remain ‘On’. Your headphones are now ready for use.

Auto-Linking With A Previously Paired Device

If your iB85 headphones were previously paired with a Bluetooth enabled device, your

headphones will attempt to auto-link with that device again whenever that device is within

the Bluetooth operating range.

1. Press and hold the Multi-function button on your iB85 headphones for about 4

seconds until the blue LED indicator slowly ﬂashes to indicate the headphones are in

the ‘Standby’ mode and searching for a previously paired device.

2. Make sure that the Bluetooth function of the previously paired device is ‘On’.

Note: If no previously paired device is found after 5 minutes the auto-linking function

stops and your iB85 headphones shut off automatically to preserve the battery life.

Switching the Power On and Off

1. Press and hold the Multi-function button for approximately 4 seconds until you hear

the power up tone. The LED indicator turns solid blue if linked or blinking blue if not

linked. This indicates that the power is ‘On’.

2. When the power is ‘On’ press and hold the Multi-function button for approximately 3

seconds until you hear the power down tone. The LED indicator brieﬂy turns red and

then shuts off. This indicates that the power is ‘Off’.

Model: iB85

Bluetooth wireless

headphones with mic

+ remote and pouch

Controls and Indicators

1. Multi-function button: Power On/Off,

Answer/End, Play/Pause, Pair

2. Power/Charging/Pairing Indicator

3. Volume +button

4. Volume

button

5. Microphone

6. Forward button

7. Back button

8. Micro USB Charging Port

(located under moisture resistant cover)

Charging Your Headphones

IMPORTANT: Your headphones operate on a built-in rechargeable lithium-ion battery. You

should charge the battery for a full 4 hours before ﬁrst time use.

1. Lift up the moisture resistant cover to expose the micro USB charging port.

2. Connect the micro USB plug on the charging cable to the micro USB port on the

headphones.

3. Connect the standard USB plug on the charging cable to any standard USB power

port such as found on a notebook computer, or the charging adapter for an iPod,

iPhone, etc.

4. The headphone will be automatically powered off once USB cable is connected.

Throughout the charging process, headphone remains off.

5. The Power/Charging/Pairing indicator will slowly ﬂash while the headphone is

charging. The indicator will turn Off when the battery is fully charged. It is

recommended not to leave the headphones charging for more than 5 hours

unattended.

Reminder: Allow the battery to charge for 4 hours before ﬁrst time use. Normal recharge

time after ﬁrst use should take about 3 hours. When fully charged the battery will provide

up to 12 hours of working time, or 360 hours of standby time.

Model: iB85 English I/B (Front)

Print color : Black text on white paper

Size of manual: 180W x 270H (mm)

Date: Aug 29, 2013

Wearing Your Headphones

Your iHome iB85 Bluetooth headphones are supplied with padded ear cushions for long

wearing comfort. The headband can be extended to accommodate almost any head

size. There are ‘L’ and ‘R’ markings on the inside of the headband. When the headphones

are worn properly the controls will be on your left ear.

Using Your Headphones

Note: Some of the functions described below may not be supported on your speciﬁc

smartphone. Check with your smartphone owner’s manual to conﬁrm the features

supported by your phone.

Your headphones must be paired with your phone and turned on to perform any of the

following operations.

Receiving/Ending A Call

When you receive an incoming call, press the Multi-function button once to answer the

call through the headphones. When you are ﬁnished speaking press the Multi-function

button once more to end/disconnect the call.

To transfer a call between the headphones and the smartphone quickly press the

Multi-function button twice.

Making A Call

When you make a call on your smartphone the call may be automatically transferred to

the headphones if your smartphone supports this automatic transfer function. If not,

quickly press the Multi-function button twice to transfer the call to the headphones.

Voice Activated Calling

If your smartphone supports this feature with the headphones, press and hold the

Multi-function button for about 2 seconds to initiate the voice activated calling function,

then follow the instructions supplied with your phone.

Last Number Redial

If your phone supports this feature, quickly press the Multi-function button twice to redial

the last number you called.

Declining A Call

If you receive a call that you would rather not accept (indicated by the caller ID on your

phone) quickly press the Multi-function button twice to decline the call.

Volume Control

Press the Volume “ +” or “ –” to adjust the volume of the incoming calls or the music

volume level.

Introduction

Your new iHome Bluetooth stereo headphones are designed to link with your Bluetooth

enabled device to allow you to wirelessly listen to music and answer phone calls within

the normal 10 meter (30 feet) Bluetooth operating range. Your headphones also feature

DSP (Digital Signal Processing) for enhanced audio plus noise reduction and echo

cancellation circuitry.

What’s Included

• Bluetooth Stereo Headphones with Folding Headband

• USB Charging Cable

• Travel Pouch

Speciﬁcations

Bluetooth speciﬁcation: Supports V2.1+ EDR with Handsfree Proﬁle 1.0,

Headset Proﬁle 1.1 and A2DP proﬁle 1.2 (Class ll)

and Audio/Video Remote Control Proﬁle AVRP

Standby time: up to 360 hours (with fully charged battery)

Talk time: up to 12 hours (with fully charged battery)

Music Playing time: up to 12 hours (with fully charged battery)

Operating Distance: up to 10 meters / 30 feet

Certiﬁcations: CE, FCC, RoHS, BQB

Pairing With a Bluetooth Enabled Device For The First Time

If your smartphone, laptop, or music player, such as the iPod touch, is Bluetooth enabled

(supports the A2DP Bluetooth Proﬁle) you may pair these iHome headphones with your

device to listen to music and make or receive calls as long as the two devices are within

the Bluetooth operating range of approximately 30 feet of each other.

1. Make sure that your Bluetooth enabled device is ‘On’.

2. Press and hold the Multi-function button on your iB85 headphone for about 7 seconds

until the blue LED ﬂashes rapidly. This indicates that the iB85 has entered the 'pairing

mode'. (NOTE: If no device is paired within 3 minutes, the iB85 will exit the pairing

mode.)

3. Turn on the Bluetooth function of your device so that it begins searching for a

compatible device.

4. “iHome iB85” should appear on your laptop, phone or music player’s compatible

devices list. You may also see a message such as “Not Paired”. Tap on that message

to complete the pairing process. If your device asks for a ‘password’ to complete the

pairing process, enter ‘0000’ on the keypad of your device.

5. When pairing is successful the screen on your device should show “iHome iB85

Connected” or similar message and the blue LED indicator on the iB85 headphones

will remain ‘On’. Your headphones are now ready for use.

Auto-Linking With A Previously Paired Device

If your iB85 headphones were previously paired with a Bluetooth enabled device, your

headphones will attempt to auto-link with that device again whenever that device is within

the Bluetooth operating range.

1. Press and hold the Multi-function button on your iB85 headphones for about 4

seconds until the blue LED indicator slowly ﬂashes to indicate the headphones are in

the ‘Standby’ mode and searching for a previously paired device.

2. Make sure that the Bluetooth function of the previously paired device is ‘On’.

Note: If no previously paired device is found after 5 minutes the auto-linking function

stops and your iB85 headphones shut off automatically to preserve the battery life.

Switching the Power On and Off

1. Press and hold the Multi-function button for approximately 4 seconds until you hear

the power up tone. The LED indicator turns solid blue if linked or blinking blue if not

linked. This indicates that the power is ‘On’.

2. When the power is ‘On’ press and hold the Multi-function button for approximately 3

seconds until you hear the power down tone. The LED indicator brieﬂy turns red and

then shuts off. This indicates that the power is ‘Off’.

Model: iB85

Bluetooth wireless

headphones with mic

+ remote and pouch

Controls and Indicators

1. Multi-function button: Power On/Off,

Answer/End, Play/Pause, Pair

2. Power/Charging/Pairing Indicator

3. Volume +button

4. Volume

button

5. Microphone

6. Forward button

7. Back button

8. Micro USB Charging Port

(located under moisture resistant cover)

Charging Your Headphones

IMPORTANT: Your headphones operate on a built-in rechargeable lithium-ion battery. You

should charge the battery for a full 4 hours before ﬁrst time use.

1. Lift up the moisture resistant cover to expose the micro USB charging port.

2. Connect the micro USB plug on the charging cable to the micro USB port on the

headphones.

3. Connect the standard USB plug on the charging cable to any standard USB power

port such as found on a notebook computer, or the charging adapter for an iPod,

iPhone, etc.

4. The headphone will be automatically powered off once USB cable is connected.

Throughout the charging process, headphone remains off.

5. The Power/Charging/Pairing indicator will slowly ﬂash while the headphone is

charging. The indicator will turn Off when the battery is fully charged. It is

recommended not to leave the headphones charging for more than 5 hours

unattended.

Reminder: Allow the battery to charge for 4 hours before ﬁrst time use. Normal recharge

time after ﬁrst use should take about 3 hours. When fully charged the battery will provide

up to 12 hours of working time, or 360 hours of standby time.

Model: iB85 English I/B (Front)

Print color : Black text on white paper

Size of manual: 180W x 270H (mm)

Date: Aug 29, 2013

Wearing Your Headphones

Your iHome iB85 Bluetooth headphones are supplied with padded ear cushions for long

wearing comfort. The headband can be extended to accommodate almost any head

size. There are ‘L’ and ‘R’ markings on the inside of the headband. When the headphones

are worn properly the controls will be on your left ear.

Using Your Headphones

Note: Some of the functions described below may not be supported on your speciﬁc

smartphone. Check with your smartphone owner’s manual to conﬁrm the features

supported by your phone.

Your headphones must be paired with your phone and turned on to perform any of the

following operations.

Receiving/Ending A Call

When you receive an incoming call, press the Multi-function button once to answer the

call through the headphones. When you are ﬁnished speaking press the Multi-function

button once more to end/disconnect the call.

To transfer a call between the headphones and the smartphone quickly press the

Multi-function button twice.

Making A Call

When you make a call on your smartphone the call may be automatically transferred to

the headphones if your smartphone supports this automatic transfer function. If not,

quickly press the Multi-function button twice to transfer the call to the headphones.

Voice Activated Calling

If your smartphone supports this feature with the headphones, press and hold the

Multi-function button for about 2 seconds to initiate the voice activated calling function,

then follow the instructions supplied with your phone.

Last Number Redial

If your phone supports this feature, quickly press the Multi-function button twice to redial

the last number you called.

Declining A Call

If you receive a call that you would rather not accept (indicated by the caller ID on your

phone) quickly press the Multi-function button twice to decline the call.

Volume Control

Press the Volume “ +” or “ –” to adjust the volume of the incoming calls or the music

volume level.

Introduction

Your new iHome Bluetooth stereo headphones are designed to link with your Bluetooth

enabled device to allow you to wirelessly listen to music and answer phone calls within

the normal 10 meter (30 feet) Bluetooth operating range. Your headphones also feature

DSP (Digital Signal Processing) for enhanced audio plus noise reduction and echo

cancellation circuitry.

What’s Included

• Bluetooth Stereo Headphones with Folding Headband

• USB Charging Cable

• Travel Pouch

Speciﬁcations

Bluetooth speciﬁcation: Supports V2.1+ EDR with Handsfree Proﬁle 1.0,

Headset Proﬁle 1.1 and A2DP proﬁle 1.2 (Class ll)

and Audio/Video Remote Control Proﬁle AVRP

Standby time: up to 360 hours (with fully charged battery)

Talk time: up to 12 hours (with fully charged battery)

Music Playing time: up to 12 hours (with fully charged battery)

Operating Distance: up to 10 meters / 30 feet

Certiﬁcations: CE, FCC, RoHS, BQB

Pairing With a Bluetooth Enabled Device For The First Time

If your smartphone, laptop, or music player, such as the iPod touch, is Bluetooth enabled

(supports the A2DP Bluetooth Proﬁle) you may pair these iHome headphones with your

device to listen to music and make or receive calls as long as the two devices are within

the Bluetooth operating range of approximately 30 feet of each other.

1. Make sure that your Bluetooth enabled device is ‘On’.

2. Press and hold the Multi-function button on your iB85 headphone for about 7 seconds

until the blue LED ﬂashes rapidly. This indicates that the iB85 has entered the 'pairing

mode'. (NOTE: If no device is paired within 3 minutes, the iB85 will exit the pairing

mode.)

3. Turn on the Bluetooth function of your device so that it begins searching for a

compatible device.

4. “iHome iB85” should appear on your laptop, phone or music player’s compatible

devices list. You may also see a message such as “Not Paired”. Tap on that message

to complete the pairing process. If your device asks for a ‘password’ to complete the

pairing process, enter ‘0000’ on the keypad of your device.

5. When pairing is successful the screen on your device should show “iHome iB85

Connected” or similar message and the blue LED indicator on the iB85 headphones

will remain ‘On’. Your headphones are now ready for use.

Auto-Linking With A Previously Paired Device

If your iB85 headphones were previously paired with a Bluetooth enabled device, your

headphones will attempt to auto-link with that device again whenever that device is within

the Bluetooth operating range.

1. Press and hold the Multi-function button on your iB85 headphones for about 4

seconds until the blue LED indicator slowly ﬂashes to indicate the headphones are in

the ‘Standby’ mode and searching for a previously paired device.

2. Make sure that the Bluetooth function of the previously paired device is ‘On’.

Note: If no previously paired device is found after 5 minutes the auto-linking function

stops and your iB85 headphones shut off automatically to preserve the battery life.

Switching the Power On and Off

1. Press and hold the Multi-function button for approximately 4 seconds until you hear

the power up tone. The LED indicator turns solid blue if linked or blinking blue if not

linked. This indicates that the power is ‘On’.

2. When the power is ‘On’ press and hold the Multi-function button for approximately 3

seconds until you hear the power down tone. The LED indicator brieﬂy turns red and

then shuts off. This indicates that the power is ‘Off’.

Model: iB85

Bluetooth wireless

headphones with mic

+ remote and pouch

Controls and Indicators

1. Multi-function button: Power On/Off,

Answer/End, Play/Pause, Pair

2. Power/Charging/Pairing Indicator

3. Volume +button

4. Volume

button

5. Microphone

6. Forward button

7. Back button

8. Micro USB Charging Port

(located under moisture resistant cover)

Charging Your Headphones

IMPORTANT: Your headphones operate on a built-in rechargeable lithium-ion battery. You

should charge the battery for a full 4 hours before ﬁrst time use.

1. Lift up the moisture resistant cover to expose the micro USB charging port.

2. Connect the micro USB plug on the charging cable to the micro USB port on the

headphones.

3. Connect the standard USB plug on the charging cable to any standard USB power

port such as found on a notebook computer, or the charging adapter for an iPod,

iPhone, etc.

4. The headphone will be automatically powered off once USB cable is connected.

Throughout the charging process, headphone remains off.

5. The Power/Charging/Pairing indicator will slowly ﬂash while the headphone is

charging. The indicator will turn Off when the battery is fully charged. It is

recommended not to leave the headphones charging for more than 5 hours

unattended.

Reminder: Allow the battery to charge for 4 hours before ﬁrst time use. Normal recharge

time after ﬁrst use should take about 3 hours. When fully charged the battery will provide

up to 12 hours of working time, or 360 hours of standby time.

Model: iB85 English I/B (Back)

Print color : Black text on white paper

Size of manual: 180W x 270H (mm)

Date: Aug 29, 2013

Listening to Music

To listen to music your headphones must be paired and connected to a laptop,

smartphone or music player that supports the A2DP Bluetooth proﬁle (see “Pairing With

a Bluetooth Enabled Smartphone or Music Player” above). To play music, use the

playback controls on the connected device. If you answer or make a call while listening to

music, the music will pause automatically until you end the call.

You may also use the buttons on the ‘L’ earpiece to control the music as follows:

Play or Pause – Press the Multi-function button once to start playback; press again to

pause; press once more to resume playback.

Track Controls – Press the button during playback to go to previous track. Press the

button during playback to go to next track.

Volume Controls – Press the “ +” or “ –” buttons to control the music playback volume.

Troubleshooting

Make sure that the headphones and the paired device are

within the Bluetooth operating range of approximately

30-feet.

Make sure that your headphones are properly paired and

connected with your Bluetooth enabled smartphone or

music player. Refer to the “Pairing” instructions in this

manual and in the manual supplied with device if

necessary.

The rechargeable battery in your headphones may be

exhausted and need to be recharged. Refer to the

“Charging Your Headphones” instructions in this manual.

The pairing settings between the headphones and your

smartphone or music player may have been erased or

deleted. Follow the “Pairing” instructions in this manual to

repair and reconnect the devices.

Turn off any other Bluetooth devices that are not being

used to reduce external interference.

Your speciﬁc model of smartphone may not support some

of the functions described in this manual. Refer to the

manual supplied with your phone for further information.

Care and Maintenance

Always remember to turn your headphones off if they will not be used for a long period of

time. Do not expose your headphones to extremely hot or cold temperatures for

extended periods. Do not expose them to direct sunlight or leave them in places such as

the dashboard of your car on a hot day. Prevent water or any other liquids from entering

the cabinets of your headphones.

Protect Your Hearing

Using these, or any headphones at high volume levels for long periods can result in

permanent hearing damage. Always start listening with volume controls on your

headphones and your paired device at a low level and then gradually increase the volume

controls to a comfortable listening level.

Important Notes

It is dangerous and illegal (in some jurisdictions) to use headphones when you are driving

a car, riding a bike or motorcycle, or operating a watercraft. Be aware of local laws and

regulations.

Do not use these headphones in situations where they might cause distractions or

prevent you from hearing warning sounds.

There are no user serviceable parts in these headphones. Do not attempt any service or

repairs on your own. Refer to the warranty for service, repair or replacement information.

Limited One-Year Warranty Information

iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI), warrants this

product to be free from defects in workmanship and materials, under normal use and conditions,

for one year of the product from the date of original purchase.

Should this product fail to function in a satisfactory manner, it is best to ﬁrst return it to the store

where it was originally purchased. Should this fail to resolve the matter and service still be required

by reason of any defect or malfunction during the warranty period, SDI will repair or, at its

discretion, replace this product without charge. This decision is subject to veriﬁcation of the

defect or malfunction upon delivery of this product to the Factory Service Center authorized by

SDI Customer Service. The product must include proof of purchase, including date of purchase.

An out-of-warranty fee for service will be charged for units that are received without proof of

purchase.

Before returning this product for service, please ﬁrst replace the batteries (if applicable) with fresh

ones, as exhausted or defective batteries are the most common cause of problems encountered.

If service is still required:

1. Call SDI Customer Service at 1-800-288-2792 for Return Authorization and for the address of

the Factory Service Center.

2. Remove the batteries (if applicable) and pack the unit in a well padded, heavy corrugated box.

SDI is not responsible for damage that occurs during shipping to the Factory Service Center.

3. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date of

purchase, if within the warranty period. Also include your name and address information, a

brief description for why the unit is being returned, and the return authorization number. No

unit can be processed without a return authorization number.

4. Write the return authorization number on the side of the shipping package and send the unit

prepaid and insured to the Factory Service Center address authorized by SDI Customer

Service.

Disclaimer of Warranty

NOTE: This warranty is valid only if the product is used for the purpose for which it was designed.

It does not cover (i) products which have been damaged by negligence or willful actions, misuse

or accident, or which have been modiﬁed or repaired by unauthorized persons; (ii) cracked or

broken cabinets, or units damaged by excessive heat; (iii) damage to digital media players, CD’s

or tape cassettes (if applicable); (iv) the cost of shipping this product to the Factory Service Center

and its return to the owner.

This warranty is valid only in the United States of America and does not extend to owners of the

product other than to the original purchaser. In no event will SDI or any of its afﬁliates, contractors,

resellers, their ofﬁcers, directors, shareholders, members or agents be liable to you or any third

party for any consequential or incidental damages, any lost proﬁts, actual, exemplary or punitive

damages. (Some states do not allow limitations on implied warranties or exclusion of

consequential damages, so these restrictions may not apply to you.) This warranty gives you

speciﬁc legal rights, and you may also have other rights which vary from state to state.

Your acknowledgement and agreement to fully and completely abide by the above mentioned

disclaimer of warranty is contractually binding to you upon your transfer of currency (money order,

cashier's check, or credit card) for purchase of your SDI product.

Questions? Visit www.ihome.com or call 1-800-288-2792 Toll Free.

B85-08292013-1(ENG) Printed in China

No Sound

Unable to Pair/Connect

Some Functions

Do Not Work

Reception is noisy

or intermittent

FCC Information

FCC Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an

uncontrolled environment.

This Device complies with RSS-210 of the IC Rules; Operation is subject to the following

two conditions:

(1) This device may not cause interference and

(2) This device must accept any interference received, including interference that may

cause undesired operation

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS

102 and compliance with RSS-102 RF exposure, users can obtain Canadian information

on RF exposure and compliance.

• Warning: Changes or modiﬁcations to this unit not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

• NOTE: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du

Canada.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils

radio RSS-210. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil

ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout

brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre

le fonctionnement.

This device complies with Part 15 of the FCC Rules, operation is subject to

the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

FCC ID: Z5YHS-BT04