Maintenance
The Air Cooler PLUS is made of sturdy ABS material. Always unplug the power
cord from the wall socket first if any malfunction should occur.
• Drain the water re ervoir if cooler i not being u ed,
and dry the unit in a well-ventilated place. To drain
the unit, remove the plug at the bottom of the unit
in bathroom or water-friendly place.
• After draining, plea e make ure the in ide i
completely dried. To peed up drying, you may
turn on the Air Cooler and pre “HIGH” peed
witch. It take about an hour for the unit to completely dry.
• Offen ive odor or weak air flow:
The HEPA filter may be full. If not changing filter,
remove filter and hake over new paper to remove
du t or u e weeper attachment to uction out du t.
• External maintenance:
Plea e wipe with oft cloth and a non-abra ive detergent.
• If the power cord i damaged, or the unit doe n’t work properly, it mu t be fixed
by an authorized agent or a imilarly qualified per on in order to avoid a hazard.
Do not immer e whole unit in water. It might cau e the breakdown or
electrical hock if the PC board or other electrical component get wet.
The u age of a chemical olution, uch a a volatile oil or bleaching,
may re ult in damage to the ABS ca ing.
If the unit i not completely dried before torage, the humidity
enclo ure of the unit provide a living environment for bacteria.
Questions & Answers
Q. Why i my Air Cooler i not blowing out cool air?
A. Plea e fill water re ervoir with very cold water. If the water you fill i the
ame temperature a the out ide air, you may place ice cube in the re ervoir.
Q. The airflow i weak, what can I do?
A. Plea e check to ee if the HEPA filter i full. For cleaning or changing the filter
you may read the maintenance ection for reference.
Q. Nothing i happening - why i my unit not turning on?
A. Plea e check to make ure the plug i connected to the wall ocket. If the power i
off via Timer, plea e turn on the power witch for normal operation.
8.
READ THIS ENTIRE MANUAL
BEFORE USING
ANY OF THE FUNCTIONS.
1. To u e a a fan and air filter: Simply pre power button ON and adju t
SPEED and SWING control to your requirement . The HEPA filter i in place
to remove 99.97% of particle from the air.
2. To u e a a waterle air cooler and air filter. Thi involve the exclu ive
Cooling Chamber and Gel Pack , found on no other air cooler . The two (2)
rectangular Gel Pack mu t go in the freezer for approximately 2 hour . When
the Gel Pack are frozen, place them in the cooling chamber ( ee diagram on
pg. 3). (Keeping a pare et of Gel Pack in the freezer will guarantee you will
alway have a cold Gel Pack to wap out when nece ary. To order additional
Gel Pack , refer to your place of purcha e or call 1-800-839-0966.) Then
pre the power ON button and adju t the SPEED and SWING control . The
HEPA filter i in place to remove 99.97% of particle from the air and the cool-
ing chamber will lower the temperature without increa ing humidity.
3. To u e the air cooler with water and air filter. Add water to the water inlet ( ee
diagram on pg. 3). U e very cold water. There are two (2) mall pla tic Ice
Pod that can be placed in your freezer for a few hour , then added to the water
in the water re ervoir. The e Ice Pod will keep the water cold much longer.
The colder the water, the cooler the air will be. Once the water and optional
Ice Pod are added, ju t pre the power ON button, and then the COOL but-
ton. Adju t the SPEED and SWING control .
The HEPA filter i in place to remove 99.97% of particle in the air.
4. To u e the air cooler a humidifier and air filter. Add water to the water re er-
voir through the water inlet ( ee diagram on pg. 3), pre Power ON button,
then COOL button. The Air Cooler PLUS will add humidity to dry air during
winter month or in low humidity area . In thi ca e, the water doe not need
to be cold.
The HEPA filter i in place to remove 99.97% of particle from the air.
Again, plea e read thi complete manual carefully before u ing any of the
above function to get maximum ervice life from your Air Cooler PLUS.
1.
!
!
!
➟
Lift up