Ikan OTT-CONTROLLER User manual

- 1 -
OTT-CONTROLLER
Manual
OTTICA IP PTZ Camera Controller VISCA, ONVIF, PELCO
www.ikancorp.com [email protected]

- 2 -
1. What is the function of CAM NUM when adding a network device?
CAM NUM will be associated and bound with the currently entered IP and port information.
It will quickly switch to the CAM NUM bound device when adding a device with the “CAM”
button.
2. How do I enter an IP address?
The camera controller doesn’t have a “.” button, so please enter the IP address with four
segments.
Take the IP address 192.168.0.1 for example. It will automatically jump to next segment when
finished inputting a segment with three numbers, 192 and 168; but after inputting a segment
with only one number, 0, you must move the joystick rightward to switch over to the next
segment to continue inputting.
3. How do I clear while in input mode?
Move the joystick leftward to clear the input information.
4. The home page of each mode refers to the displayed page when the controller
initialization is complete.
In IP VISCA and ONVIF Mode, if you see the prompts of “Visca!” and “Onvif!”, the IP
address displayed on the screen is local IP address of the controller. While the prompts of
“Visca:” and “Onvif:” are shown on the page, the IP address displayed on-screen belongs to
the connected device.
Precautions

- 3 -
Precautions 2
1. Product Overview 4
1.1 Product Features 4
1.2 Wiring Diagram 4
1.3 Technical Specifications 5
2. Function Description 5
2.1 Button Description 5
2.2 Rocker Switch and Knob 7
2.3 Joystick Control 7
2.4 Terminal Description of Back Panel Interfaces 8
3. Local Settings (SETUP) 8
3.1 Basic Settings 8
3.2 VISCA & IP VISCA Mode Shared Setting 9
3.3 IP VISCA Mode Setting 9
3.4 VISCA Mode Setting 9
3.5 PELCO Mode Setting 9
3.6 ONVIF Mode Setting 10
4. Connection and Control 10
4.1 Connection and Control in ONVIF Mode 10
4.2 Connection and Control in IP VISCA Mode 11
4.3 Control in VISCA & PELCO Mode 11
5. Web Page Configuration 11
5.1 Home Page 11
5.2 LAN Settings 12
5.3 Upgrade 13
5.4 Restore Factory 13
5.5 Reboot 13
Support, Warranty, Copyright 14
Table of Contents

- 4 -
1. Product Overview
1.1 Product Features
1.2 Wiring Diagram
Two IP control modes: IP VISCA & ONVIF
Two analog control modes: RS422 & RS232
Three Control Protocols: VISCA, ONVIF and PELCO
Both the Controller and PTZ camera must be connected to the same LAN. The IP addresses of
both the PTZ Camera and Controller must operate within the same network segment.
For example:
192.168.1.123 is within the same segment as 192.168.1.111
192.168.1.123 is not within the same segment as 192.168.0.125

- 5 -
1.3 Technical Specifications
Ethernet 1 x Ethernet Port
Joystick Four-dimensional joystick control (up, down, left, right)
Rotatable for zooming Tele/Wide
Connection Lead
Display LCD
Prompt Tone Button Sound Prompts On/Off
Power Supply DC 12V1A±10%
Power Consumption 0.6 W Max
Operating Temperature 32°F-122°F
Storage Temperature -4°F-158°F
Dimensions 320 x 180 x 100mm
2. Function Description
2.1 Buntton Description

- 6 -
[AUTO FOCUS] Sets the camera in auto focus mode with this button. It will light up when the
camera is in manual focus mode.
[AE AUTO] (Auto Aperture) Set the camera in automatic aperture mode with this button. It will
light up when camera is in manual aperture mode.
[CAMERA OSD] Call/Close the camera OSD
[HOME] Returns the camera back to home position if camera OSD is off. When the camera
OSD is on, the home button confirms the function of camera OSD.
[F1]~[F2] Custom function buttons. In VISCA and IP VISCA modes.
[SETUP] Local settings button, modifies & views local settings. Navigate menus using Joystick.
[SEARCH] Search for all available devices with ONVIF protocol in the LAN (only in ONVIF Mode).
[INQUIRE] Check added devices.
[WBC MODE] (Auto White Balance) Sets the camera in auto white balance mode. Button will
light up when camera is in manual white balance mode.
[CAM1]~[CAM4] Quickly switch device button: Quickly switch to CAM NUM 1-4 devices
(ONVIF, IP VISCA), or to address code 1-4 devices (VISCA, PELCO).
[PRESE] Short presses will enable you to set presets; long presses will enable you to delete
presets. Use the number keys and the “ENTER” button, when setting or deleting presets.
[CALL] Use the number keys and “ENTER” button to move the camera to a preset.
[IP] Manually adds network devices (only in ONVIF and IP VISCA modes). Use the “ENTER”
button to confirm each step of the setup.
[CAM] In IP VISCA and ONVIF modes, it will quickly switch to the CAM NUM bound device when
adding a device via CAM.
In VISCA and PELCO modes, it will switch to the address code when entering a certain address.
Use the “”ENTER” button to confirm each step of the setup.
[1]~[9] Number keys of 0,1,2,3,4,5,6,7,8,9.
2,4,6,8 also serve as directional keys, which can control pan and tilt rotation, and camera OSD.
[ESC] Return
[ENTER] Confirm Button. Be sure to press this button to confirm any/all settings.

- 7 -
2.2 Rocker Switch and Knob
2.3 Joystick Control
[NEAR] [FAR] Manually adjust the focal length.
[OPEN] [CLOSE] Manually adjust the aperture, OPEN(Aperture Plus)/CLOSE(Aperture minus)
[R-] [R+] Manually adjust the Red Gain
[B-] [B+] Manually adjust the Blue Gain
[PTZ SPEED-] [PTZ SPEED+] Adjust PTZ Speed 1-8: “-” = Slow. “+” = Fast.
[T-ZOOM-W] Zoom Tele and Zoom Wide

- 8 -
2.4 Terminal Description of Back Panel Interfaces
Back Panel Details: RS422, RS232, DC-12V, Ethernet, Power Switch
Move the joystick up and down to switch between basic settings. Move the joystick left or right
to alter settings. Confirm settings with “ENTER” button.
1. Delete Device
2. Network Type: Dynamic and Static
3. Button Sound Prompt: On and Off
4. Language Setting: English and Chinese
5. Mode: VISCA, IP VISCA, ONVIF, PELCO
Number Label Physical Interface Description
1 RS422 Control Output
(TA, TB, TA, TB)
Connect to RS422 bus of the camera:
TA to camera RA
TB to camera RB
RA to camera TA
RB to camera TB
2 Ground Control line ground (G) Control signal Line ground
3 ETHERNET Ethernet Port Network Connection
4 DC-12V Power Input DV 12V Power Input
5 POWER Power Switch Power ON / OFF
3. Local Settings (SETUP)
3.1 Basic Settings
6. Local IP
7. Version Information
8. Restore Factory Settings
9. Function Button 1 (“F1”) Setup
10. Function Button 2 (“F2”) Setup

- 9 -
3.2 VISCA & IP VISCA Mode Shared Setting
3.3 IP VISCA Mode Setting
3.4 VISCA Mode Setting
3.5 PELCO Mode Setting
1. F1: Custom function for F1 button (VISCA command)
2. F2: Custom function for F2 button (VISCA command)
Input custom name > ENTER > Input VISCA command
For example: If the command is 8101040702FF, then input 01040702 (0 can’t be omitted)
Delete the saved device:
Move the joystick up and down to view devices; Move the joystick rightward to view the
device’s port information; Move the joystick leftward to view the IP, CAM NUM information;
ENTER to delete the selected device.
Control Settings (set the baud rate for a certain address code):
Move the joystick up, down, left and right to switch addresses (1-7) > ENTER > Move the
joystick left and right to switch baud rate > ENTER
EX: Select the address: 1 > ENTER > Select the baud rate: 9600 > ENTER
When the controller is switched to address 1, the control baud rate is 9600
Control Settings (set the baud rate for a certain address code):
Move the joystick up, down, left and right to switch addresses (1-255) > ENTER > Move the
joystick left and right to choose protocols > ENTER > Move the joystick left and right to switch
baud rate > ENTER

- 10 -
3.6 ONVIF Mode Setting
Delete Saved Device:
Move the joystick up and down to view devices. Move the joystick rightward to view the
device’s port information. Move the joystick leftward to view the IP, CAM NUM information.
Press “ENTER” to delete the selected device.
EX: Select the address: 1 > ENTER > Select the protocol: PELCO-D > ENTER > Select the baud
rate: 9600 > ENTER
When the controller is switched to address 1, the control baud rate is 9600, protocol is
PELCO-D
Search and Add
In ONVIF mode, follow the steps below to add a LAN device to the PTZ controller:
4. Connection and Control
4.1 Connection and Control in ONVIF Mode
1. After the controller has obtained IP address, simply press the SEARCH button.
2. All available devices with the ONVIF protocol in the LAN will be displayed on the controller
when search process is complete.
3. Move the joystick up/down to select the device. Press the “ENTER” button to confirm.
4.It’s required to enter the device’s username, password and CAM NUM information when
adding a device.
5. Press the “ENTER” button to save.
6. Alternatively, use the [IP] button to add a device manually.
7. Press the “INQUIRE” button to view the added device. Move the joystick up/down to view the
saved device (move the joystick rightward to view the port). Press the “ENTER” button to select
a camera to control, or use the CAM button to connect and control.