Ikelite 9523.61 User manual

Tray with Handle(s)
Instruction Manual
9523.61 Tray with Single Handle
9523.62 Tray with Dual Handles
Thank you for choosing Ikelite equipment. Please read this instruction
manual completely before attempting to operate or dive with this product.
Package Contents
12-24 houlder Washer (Qty. 2)
1/4” Nut (Qty. 2 with Dual Tray)
12-24 x 1/2” crew (Qty. 2)
Flat Washer (Qty. 2 with Dual Tray)
plit Lock Washer
1/4-20 x 1/2” crew
(Qty. 2)
3/8-16 Nut
(Qty. 2)
1/4-20 houlder Washer (Qty. 2)
Quick Release Handle
(Qty. 2 with Dual Tray)
OLYMPUS
CANON A
CANON B
CANON C
SONY B
SONY A
Panasonic
Tray Inserts
Front o Tray
mall Flat Washer
(Qty. 2 with Dual Tray)

2
Insert handle into the tray as shown below. Attach and tighten to tray
using flat washer and 1/4” nut. The handle is removable in the event that
replacement is necessary. The handle is not intended to be removed for
travel. The completed assembly may be removed and replaced easily for
travel.
Attaching Handle to the Tray
1/4” Nut
Threaded Handle tem
Flat Washer
Handle
Guide
Pin
Quick
Release
Handle
tem Hole
mall Hole
mall Flat Washer

3
Match your housing
to the correct tray
insert as shown.
The insert cut-out
should match the
bottom of the
housing tripod mount base plate,
diagram A. Remove protective backing to expose adhesive and attach
insert to recess in the center of the tray, diagram B. Attach tray to
housing through Center Hole using 1/4-20 x 1/2” crew and plit Lock
Washer, diagram C.
Canon, Olympus, Panasonic, and Sony Housings
OLYMPUS
CANON A
CANON B
CANON C
SONY B
SONY A
Panasonic
SONY B
SONY A
Panasonic
Diagram A Diagram B
SONY B
SONY A
Panasonic
Protective
Backing
Diagram C
plit Lock Washer
1/4-20 x 1/2” crew
Front o Tray
Tray Inserts
Center
Hole
1/4-20
Threaded
Mounting
Hole

Attach tray to Ikelite housing using two 12-24 x 1/2” crews and
houlder Washers for housings with female-threaded mounting systems.
For male-threaded mounting systems with a housing serial number
less than 37,101, order spacer 9523.09. Tighten tray with spacer using
the two 3/8-16 nuts. 12-24 x 1/2” crew
houlder Washer
Housing Mount
This product is warranted against any manufacturing defects for a period
of one (1) year from the original date of purchase. Defective products
should be returned to Ikelite postage paid. Ikelite will, at its sole
discretion, repair or replace such products, and will return to customer
postage paid. All other claims of any nature are not covered. Except as
mentioned above, no other warranty expressed or implied applies to this
Ikelite product.
Ikelite Underwater Systems
50 West 33rd Street
Indianapolis, IN 46208 USA
9523.61.62_Tray_Handle(s)_4-0113
Limited Warranty
Accessory Mounting Points
The bottom of the tray features two 1/4-20 threaded mounting holes for
attachment of a Pro-Video battery pack, diagram B, page 3.
Ikelite Housings