iKey SL-75-OEM Operating and safety instructions

Part Number: SL-75-OEM
Drawing Title: DIMENSIONS/ FEATURES Date:
Sheet:
JAE
Drawing Number:
Revision: 1.0
MKT0043 1OF 2
2.21.05
SL-75-OEM
Voice: [phone]

Fax: [phone]
©2005 IKEY,LP
IKEY, LTD

2621 Ridgepoint Dr. Suite 235

Austin, Texas 78754
Esc
QWE RT Y U I OP
ASDFGHJKL
ZXCVBNM
!
1
@
2
#
3
$
4
%
5
^
6
&
7*
8
(
9
)
0
_
-
+
=
{
[
}
]\
<
,>
.?
/Shift
:
;"
'
Backspace
Pg Up
Pg Dn
Home End
Caps
Lock
~
`
Shift
Fn Ctrl
Del
Ins
Alt
F3 F4 F5 F6 F7
F1 F2
F11 F12
F8 F9 F10
Scroll
Lock Print
Screen
Pause
POWER
KEY SWITCH TEMPERATURE
FLAMMABILITY
HUMIDITY
SHOCK
VIBRATION
MATERIAL: industrial Silicone Rubber
LIFE: Greater than 10 million cycles
TRAVEL: 0.055 in.
ACTUATION FORCE: 5 oz. (130g)
FEEDBACK: Tactile with Mechanical Snap
100% Humidity Resistant
KEYBOARD: 5V@20ma (from CPU port)
5V @200ma (with backlight on)
PRINTED CIRCUIT BOARD: 94VO
SILICONE OVERLAY: 94HB 
INTERFACE CABLE: 94VO
Storage: -40 F to +194 F (-40 C to +90 C)
Operating: -40 F to +140 F (-40 C to +60 C)
3 X 11 ms pulses of 50g on each of 3 axis
POWER SPECTRAL DENSITY: .04g/HZ
FREQUENCY RANGE: 20Hz-2Khz
DURATION OF TEST PER AXIS: 3 hours
3.850"
7.850"
0.518"
0.063"
0.123"
0.193"
0.318"
PCB
IC on 
board

MOUNTING: HORIZONTAL 7.85"
VERTICAL 3.5"
DEPTH 0.39"

PANEL THICKNESS: 0.06" TO 0.08"
KEY HEIGHT ABOVE PANEL: 0.165"
KEY TRAVEL: 0.055"
POWER: 5 Vdc @ 20 mA, PROVIDED
BY HOST CPU
TEMPERATURE: OPERATING FROM 
0 F TO 140 F (-20 C TO 60 C)
Mounting Instructions:

1. Turn panel face-down.
2. Seat keypad into the panel with back facing up. Seat the
keypad in the mounting cutout one edge at a time.
3. Apply silicone adhesive [IKEY recommends SuperFlex by Loctite]
to back side of silicone overlay (keypad)
-a small amount should be applied to the the ridges 
between every other key and on each row. 
-be sure not to drop silicone on any key contacts
Date:
Sheet:
Drawing Number:



Part Number: SL-75-OEM
Drawing Title: MOUNTING CUTOUT JAE
Revision: 1.0
MKT0043 2 OF 2
2.21.05
Voice: [phone]

Fax: [phone]
©2005 IKEY,LP
IKEY, LTD

2621 Ridgepoint Dr. Suite 235

Austin, Texas 78754
.178"
1.914"
3.828"
5.742"
7.655"
.177"
1.218"
2.436"
3.654"
7.300"
3.300"
CUTOUT
5. Place the PCB (circut board) onto the panel studs , ensuring 
that no adhesive is misplaced on a key switch.
7. When the board is in place, allow it to fall onto the keypad.
8. Spread the keypad to be sure it is well seated on all four sides.
You may need to look at other side of panel to assure there
are no gaps in the corners.
9. Tighten hex nuts until keypad is just SLIGHTLY compressed 
between panel and PCB.