iKeyless MTHKL-G000 User manual

MTHKL-G000
User’s Guide
1
iKeyless LLC Confidential

Button Functions
2
iKeyless LLC Confidential
LOCK: Used for hundred’s selection
PANIC: Used for ten’s selection
UNLOCK: Used for one’s selection
TRUNK: Not used for programming

Programming Procedure
To enter programming mode, press and hold LOCK and PANIC simultaneously.
- LED will illuminate steadily
Enter activation code. For example, code 242 would be entered by;
-242, pressing LOCK twice
- 242, pressing PANIC four times
- 242, pressing UNLOCK twice
- LED will blink with each button press
To exit programming mode, again press and hold LOCK and PANIC simultaneously.
- If a valid code was entered, LED will blink once.
- If an invalid code was entered, LED will blink three times.
If no code is entered after a time, LED will blink and key will exit programming mode
automatically.
3
iKeyless LLC Confidential

Battery Replacement
4
iKeyless LLC Confidential
Using a small screwdriver,
pry open outer shell
Remove inner shell
Using small screwdriver, pry open inner
shell
Replace CR1620 battery with positive
terminal down
Press inner shell together, replace in
outer shell, then press outer shell together
Inner Shell
CR1620

Using the Remote
5

FCC Regulatory Statement
Model: MTHKL-G000
FCC ID: X32-MTHKG000
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this device not expressly approved by iKeyless, LLC could void the user’s authority to operate the equipment.
6

IC Regulatory Statement
Model: MTHKL-G000
IC: 8797A-MTHKG000
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum
(or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication. This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne
d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les
risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte
que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une
communication satisfaisante. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
7